re-format and re-word the device tree binding documentation for MPC8xxx
and compatibles, reference the common document for interrupt controllers
and remove outdated duplicate SoC specific information
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Rob Herring@ <rob.herring@xxxxxxxxxxx>
Cc: Pawel Moll <Pawel.Moll@xxxxxxx>
Cc: Arnd Bergmann <arnd@xxxxxxxx>
Cc: <devicetree@xxxxxxxxxxxxxxx>
Acked-by: Arnd Bergmann <arnd@xxxxxxxx>
Signed-off-by: Gerhard Sittig <gsi@xxxxxxx>
---
changes in v2:
- s/CHIP/chip/ in 'compatible', s/and/or/ for the
list of strings to use in 'compatible'
- "should be two" and "s/specific/available/ set of
trigger conditions" in '#interrupt-cells'
- IRQ controller properties added to the 'gpio1' example node
as it is referenced as one from 'funkyfpga'
---
.../devicetree/bindings/gpio/8xxx_gpio.txt | 66 ++++++++++++--------
1 file changed, 40 insertions(+), 26 deletions(-)
diff --git a/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt
index b0019eb5330e..798cfc9d3839 100644
--- a/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt
@@ -5,16 +5,42 @@ This is for the non-QE/CPM/GUTs GPIO controllers as found on
Every GPIO controller node must have #gpio-cells property defined,
this information will be used to translate gpio-specifiers.
+See bindings/gpio/gpio.txt for details of how to specify GPIO
+information for devices.
+
+The GPIO module usually is connected to the SoC's internal interrupt
+controller, see bindings/interrupt-controller/interrupts.txt (the
+interrupt client nodes section) for details how to specify this GPIO
+module's interrupt.
+
+The GPIO module may serve as another interrupt controller (cascaded to
+the SoC's internal interrupt controller). See the interrupt controller
+nodes section in bindings/interrupt-controller/interrupts.txt for
+details.
Required properties:
-- compatible : "fsl,<CHIP>-gpio" followed by "fsl,mpc8349-gpio" for
- 83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx.
-- #gpio-cells : Should be two. The first cell is the pin number and the
- second cell is used to specify optional parameters (currently unused).
- - interrupts : Interrupt mapping for GPIO IRQ.
- - interrupt-parent : Phandle for the interrupt controller that
- services interrupts for this device.
-- gpio-controller : Marks the port as GPIO controller.
+- compatible: "fsl,<chip>-gpio" followed by "fsl,mpc8349-gpio"
+ for 83xx, "fsl,mpc8572-gpio" for 85xx, or
+ "fsl,mpc8610-gpio" for 86xx.
+- #gpio-cells: Should be two. The first cell is the pin number
+ and the second cell is used to specify optional
+ parameters (currently unused).
+- interrupt-parent: Phandle for the interrupt controller that
+ services interrupts for this device.
+- interrupts: Interrupt mapping for GPIO IRQ.
+- gpio-controller: Marks the port as GPIO controller.
+
+Optional properties:
+- interrupt-controller: Empty boolean property which marks the GPIO
+ module as an IRQ controller.
+- #interrupt-cells: Should be two. Defines the number of integer
+ cells required to specify an interrupt within
+ this interrupt controller. The first cell
+ defines the pin number, the second cell
+ defines additional flags (trigger type,
+ trigger polarity). Note that the available
+ set of trigger conditions supported by the
+ GPIO module depends on the actual SoC.
Example of gpio-controller nodes for a MPC8347 SoC:
@@ -22,39 +48,27 @@ Example of gpio-controller nodes for a MPC8347 SoC:
#gpio-cells = <2>;
compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
reg = <0xc00 0x100>;
- interrupts = <74 0x8>;
interrupt-parent = <&ipic>;
+ interrupts = <74 0x8>;
gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
};
gpio2: gpio-controller@d00 {
#gpio-cells = <2>;
compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
reg = <0xd00 0x100>;
- interrupts = <75 0x8>;
interrupt-parent = <&ipic>;
+ interrupts = <75 0x8>;
gpio-controller;
};
-See booting-without-of.txt for details of how to specify GPIO
-information for devices.
-
-To use GPIO pins as interrupt sources for peripherals, specify the
-GPIO controller as the interrupt parent and define GPIO number +
-trigger mode using the interrupts property, which is defined like
-this:
-
-interrupts = <number trigger>, where:
- - number: GPIO pin (0..31)
- - trigger: trigger mode:
- 2 = trigger on falling edge
- 3 = trigger on both edges
-
-Example of device using this is:
+Example of a peripheral using the GPIO module as an IRQ controller:
funkyfpga@0 {
compatible = "funky-fpga";
...
- interrupts = <4 3>;
interrupt-parent = <&gpio1>;
+ interrupts = <4 3>;
};
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
