On Wed, Jun 1, 2016 at 9:49 AM, Laxman Dewangan <ldewangan@xxxxxxxxxx> wrote: > > On Tuesday 31 May 2016 09:18 PM, Rob Herring wrote: >> >> On Tue, May 31, 2016 at 8:44 AM, Laxman Dewangan <ldewangan@xxxxxxxxxx> >> wrote: >>> >>> Hi Rob, >>> >>> On Tuesday 31 May 2016 07:05 PM, Rob Herring wrote: >>>> >>>> On Tue, May 31, 2016 at 2:35 AM, Chanwoo Choi <cw00.choi@xxxxxxxxxxx> >>>> wrote: >>>>> >>>>> The extcon-gpio.c driver can separate the kind of external connector >>>>> by using the 'extcon-id' property. >>>> >>>> This use of DT is just broken. Come up with another way. >>>> >>>> >>> >>> Can we have the DT binding very similar to IIO, clock, reset etc? >> >> In what way? I'm guessing you mean to describe what controller a >> connector is associated with. Certainly, some sort of phandle >> reference will be needed. However. the node it points to is what needs >> a lot of work first. > > > Here, we just need to define that controller support how many different > cable? It does not say anything that which cable is what and all its on > platform dependent. > > So for gpio-extcon, it will just say 1 cable. the name is not decided by > driver but it is by platform. Why the fascination with cables? You need to describe the connector and circuitry between the connector and phy/controller, and its capabilities. Maybe those properties are implied or explicit. If you have some USB chip for Vbus control and charger detect, then it's all going to be implied by that chip's compatible. If you have gpio lines then the properties and capabilities are explicit. >>> Here is details for extcon-jack DT binding and its client: >>> >>> The client can get the cable information through its node or extcon name >>> and once cable information is available, it can register for notification >>> when state gets changed. >>> >>> The typical dt nodes are: >>> >>> Extcon-driver node: >>> >>> extcon: arizona-extcon { >>> compatible = "wlf,arizona-extcon"; >>> #extcon-cells = <1>; >>> }; >>> >>> >>> >>> Driver need to specify the cable ID as >> >> Unless you have cables hardwired to a board, please stop describing >> cables in DT. Connectors! > > > If some controller only support cable with names then we need to do it. Like > palmas extcon, it detect VBUS, ID_GND, RIDA, RIDB, RIDC. So for these cases, > driver need to define cables. The only thing the DT should have is the palmas chip and any connections to it like regulators or interrupts. What the chip can control/detect doesn't belong in DT. > Driver can specify that cable index 0 is for VBUS, 1 is for ID-GND etc. You are still just making up indexes. >>> Cable ID >>> ---------------------------- >>> Mechanical 0 >>> Microphone 1 >>> Headphone 2 >>> Line-out 3 >> >> No, please don't create some made up some number space. I don't see >> why you need this. You should just need the phandle to "the microphone >> jack" node. > > > I am thinking that I will need the phandle of extcon nodes with index for > cable ID. > > >>> Here #extcon-cells is must and specifies the size of extcon cells. >>> The >>> client need to provide the driver specific information as argument along >>> with handle. >>> >>> >>> Extcon Client node: >>> >>> audio-controller@b0000 { >>> :::: >>> extcon-cables = <&extcon 1>, <&extcon 3>; >>> extcon-cable-names = "Microphone", "Line-out"; >>> }; >>> >>> and client driver can register the cable by passing the cable name >>> as above along with its node. >>> >>> struct extcon_cable { >>> struct extcon_dev *edev, >>> int cable_id; >>> }; >> >> If you are showing driver details to explain the binding, something is >> wrong. > > > > I have USB OTG driver which need the notification when VBUS or ID detected. That's a kernel architectural detail. > For this, it can get the phandle of extcon and cable ID from that driver for > "id" and "vbus". You only need to describe the connection of the connector to the controller. These details don't need to be in DT. > I have platform like follows: > I have 2 gpios which detect the ID and VBUS. > Both are independent. My USB driver get the extcon handle from the DT: > > extcon_vbus: extcon@0 { > comptaible = "extcon-gpio"; > gpio = <&gpio JETSON_VBUS_GPIO 0>; > #extcon-cells = <1>; > }; > > > > extcon_id: extcon@1 { > comptaible = "extcon-gpio"; > gpio = <&gpio JETSON_ID_GPIO 0>; > #extcon-cells = <1>; > }; Sigh. These are all properties of one entity: a connector. > > usb-otg { > :: > extcon-cable = <&extcon_vbus 0 &extcon_d 0>; > extcon-cable-names = "id", "vbus"; > :: > }; Rob -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html