On Wed, May 25, 2016 at 05:43:03AM +0000, Rich Felker wrote: > Signed-off-by: Rich Felker <dalias@xxxxxxxx> > --- > arch/sh/boot/dts/j2_mimas_v2.dts | 87 ++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 87 insertions(+) > create mode 100755 arch/sh/boot/dts/j2_mimas_v2.dts > > diff --git a/arch/sh/boot/dts/j2_mimas_v2.dts b/arch/sh/boot/dts/j2_mimas_v2.dts > new file mode 100755 > index 0000000..4a66cda > --- /dev/null > +++ b/arch/sh/boot/dts/j2_mimas_v2.dts > @@ -0,0 +1,87 @@ > +/dts-v1/; > + > +/ { > + compatible = "jcore,j2-soc"; > + model = "J2 FPGA SoC on Mimas v2 board"; > + > + #address-cells = <1>; > + #size-cells = <1>; > + > + interrupt-parent = <&aic>; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + > + cpu@0 { > + device_type = "cpu"; > + compatible = "jcore,j2"; > + reg = < 0 >; > + clock-frequency = < 50000000 >; Nit: please remove the spacing around the '<' and '>' here. If nothing else, it's inconsistent with the rest of this file. > + }; > + }; > + > + memory@10000000 { > + device_type = "memory"; > + reg = < 0x10000000 0x4000000 >; > + }; Likewise. > + > + chosen { > + stdout-path = "/soc@abcd0000/serial@100"; > + }; Please use a label for the serial node, have an alias, and describe the pre-configured rate per the stdout-path binding, e.g. aliases { serial0 = &uart0; }; chosen { stdout-path = "serial0:19200n8"; }; ... soc@abcd0000 { ... uart0: serial@100 { ... }; }; Note that using stdout-path is preferable to current-speed or other UART-specific bindings. Thanks, Mark. > + > + soc@abcd0000 { > + compatible = "simple-bus"; > + ranges = <0 0xabcd0000 0x100000>; > + > + #address-cells = <1>; > + #size-cells = <1>; > + > + aic: interrupt-controller@200 { > + compatible = "jcore,aic1"; > + reg = < 0x200 0x10 >; > + interrupt-controller; > + #interrupt-cells = <1>; > + }; > + > + cache-controller@c0 { > + compatible = "jcore,cache"; > + reg = < 0xc0 4 >; > + }; > + > + timer@200 { > + compatible = "jcore,pit"; > + reg = < 0x200 0x30 >; > + interrupts = < 0x48 >; > + }; > + > + spi@40 { > + compatible = "jcore,spi2"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + spi-max-frequency = <12500000>; > + > + reg = < 0x40 0x8 >; > + > + sdcard@0 { > + compatible = "mmc-spi-slot"; > + reg = <0>; > + spi-max-frequency = <12500000>; > + voltage-ranges = <3200 3400>; > + mode = <0>; > + }; > + }; > + > + serial@100 { > + clock-frequency = <125000000>; > + compatible = "xlnx,xps-uartlite-1.00.a"; > + current-speed = <19200>; > + device_type = "serial"; > + interrupts = < 0x12 >; > + port-number = <0>; > + reg = < 0x100 0x10 >; > + }; > + }; > +}; > -- > 2.8.1 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html