Hi Marek,
I encountered a issue with this driver while testing.
On 1/11/2016 10:04 AM, Marek Vasut wrote:
> From: Graham Moore <grmoore@xxxxxxxxxxxxxxxxxxxxx>
>
> Add support for the Cadence QSPI controller. This controller is
> present in the Altera SoCFPGA SoCs and this driver has been tested
> on the Cyclone V SoC.
> +static void cqspi_switch_cs(struct spi_nor *nor)
> +{
> + struct cqspi_flash_pdata *f_pdata = nor->priv;
> + struct cqspi_st *cqspi = f_pdata->cqspi;
> + void __iomem *iobase = cqspi->iobase;
> + unsigned int reg;
> +
> + cqspi_controller_enable(cqspi, 0);
> +
> + /* configure page size and block size. */
> + reg = readl(iobase + CQSPI_REG_SIZE);
> + reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
> + reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
> + reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
> + reg |= (nor->page_size << CQSPI_REG_SIZE_PAGE_LSB);
> + reg |= (ilog2(nor->mtd.erasesize) << CQSPI_REG_SIZE_BLOCK_LSB);
> + reg |= (nor->addr_width - 1);
> + writel(reg, iobase + CQSPI_REG_SIZE);
> +
Page size and block size are configured here...
> + /* configure the chip select */
> + cqspi_chipselect(nor);
> +
> + cqspi_controller_enable(cqspi, 1);
> +}
> +
> +static int cqspi_prep(struct spi_nor *nor, enum spi_nor_ops ops)
> +{
> + struct cqspi_flash_pdata *f_pdata = nor->priv;
> + struct cqspi_st *cqspi = f_pdata->cqspi;
> + const unsigned int sclk = f_pdata->clk_rate;
> +
> + /* Switch chip select. */
> + if (cqspi->current_cs != f_pdata->cs) {
> + cqspi->current_cs = f_pdata->cs;
> + cqspi_switch_cs(nor);
cqspi_switch_cs(nor) is called from cqspi_prep(). And is called only
once for a given slave (assuming only one slave on the QSPI bus)
> + }
> +
> + /* Setup baudrate divisor and delays */
> + if (cqspi->sclk != sclk) {
> + cqspi->sclk = sclk;
> + cqspi_controller_enable(cqspi, 0);
> + cqspi_config_baudrate_div(cqspi, sclk);
> + cqspi_delay(nor, sclk);
> + cqspi_readdata_capture(cqspi, 1, f_pdata->read_delay);
> + cqspi_controller_enable(cqspi, 1);
> + }
> +
> + return 0;
> +}
> +
> +static int cqspi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
> +{
> + int ret;
> +
> + ret = cqspi_set_protocol(nor, nor->reg_proto);
> + if (ret)
> + return ret;
> +
> + cqspi_prep(nor, SPI_NOR_OPS_READ);
cqspi_read_reg() is first called to read JEDEC ID, this calls
cqspi_prep() for first time. But nor->page_size, nor->mtd.erasesize are
not yet populated. Therefore cqspi_switch_cs() will not populate
CQSPI_REG_SIZE with correct values.
I think its better to configure this register each time during
read/write ops.
Regards
Vignesh
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
