Add pinctrl and gpio DT bindings for Oxford Semiconductor OXNAS SoC Family.
This version supports the ARM926EJ-S based OX810SE SoC with 34 IO pins.
Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
---
.../devicetree/bindings/gpio/gpio_oxnas.txt | 43 ++++++++++++++++
.../devicetree/bindings/pinctrl/oxnas,pinctrl.txt | 57 ++++++++++++++++++++++
2 files changed, 100 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt
diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
new file mode 100644
index 0000000..ddd3de9
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
@@ -0,0 +1,43 @@
+* Oxford Semiconductor OXNAS SoC GPIO Controller
+
+Required properties:
+ - compatible: "oxsemi,ox810se-gpio"
+ - reg: Base address and length for the device.
+ - interrupts: The port interrupt shared by all pins.
+ - gpio-controller: Marks the port as GPIO controller.
+ - #gpio-cells: Two. The first cell is the pin number and
+ the second cell is used to specify the gpio polarity as defined in
+ defined in <dt-bindings/gpio/gpio.h>:
+ 0 = GPIO_ACTIVE_HIGH
+ 1 = GPIO_ACTIVE_LOW
+ - interrupt-controller: Marks the device node as an interrupt controller.
+ - #interrupt-cells: Two. The first cell is the GPIO number and second cell
+ is used to specify the trigger type as defined in
+ <dt-bindings/interrupt-controller/irq.h>:
+ IRQ_TYPE_EDGE_RISING
+ IRQ_TYPE_EDGE_FALLING
+ IRQ_TYPE_EDGE_BOTH
+ - gpio-ranges: Interaction with the PINCTRL subsystem.
+
+Example:
+
+gpio0: gpio@0 {
+ compatible = "oxsemi,ox810se-gpio";
+ reg = <0x000000 0x100000>;
+ interrupts = <21>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&pinctrl 0 0 32>;
+};
+
+keys {
+ ...
+
+ button@sw1 {
+ label = "ESC";
+ linux,code = <1>;
+ gpios = <&gpio0 12 0>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt
new file mode 100644
index 0000000..d607432
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt
@@ -0,0 +1,57 @@
+* Oxford Semiconductor OXNAS SoC Family Pin Controller
+
+Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and
+../interrupt-controller/interrupts.txt for generic information regarding
+pin controller, GPIO, and interrupt bindings.
+
+OXNAS 'pin configuration node' is a node of a group of pins which can be
+used for a specific device or function. This node represents configurations of
+pins, optional function, and optional mux related configuration.
+
+Required properties for pin controller node:
+ - compatible: "oxsemi,ox810se-pinctrl"
+ - oxsemi,sys-ctrl: a phandle to the system controller syscon node
+
+Required properties for pin configuration sub-nodes:
+ - pins: List of pins to which the configuration applies.
+
+Optional properties for pin configuration sub-nodes:
+----------------------------------------------------
+ - function: Mux function for the specified pins.
+ - bias-pull-up: Enable weak pull-up.
+
+Example:
+
+pinctrl: pinctrl {
+ compatible = "oxsemi,ox810se-pinctrl";
+
+ /* Regmap for sys registers */
+ oxsemi,sys-ctrl = <&sys>;
+
+ pinctrl_uart2: pinctrl_uart2 {
+ uart2a {
+ pins = "gpio31";
+ function = "fct3";
+ };
+ uart2b {
+ pins = "gpio32";
+ function = "fct3";
+ };
+ };
+};
+
+uart2: serial@900000 {
+ compatible = "ns16550a";
+ reg = <0x900000 0x100000>;
+ clocks = <&sysclk>;
+ interrupts = <29>;
+ reg-shift = <0>;
+ fifo-size = <16>;
+ reg-io-width = <1>;
+ current-speed = <115200>;
+ no-loopback-test;
+ status = "disabled";
+ resets = <&reset 22>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
