Re: [PATCH 10/12] ARM: dts: dragonboard-600c: Add on board leds support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Thanks Bjorn,

On 27/03/16 06:50, Bjorn Andersson wrote:
On Wed 23 Mar 12:48 PDT 2016, Srinivas Kandagatla wrote:

This patch adds support to 4 user leds, wlan and bt led on board.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>

I'm not fond of the overly complicated names; and I think it should at
least be shortened to "db600c:...".

I agree, I will fix this in next version.


Tested this on my DB600c, seems to work, except the WiFi/BT triggers,
see comments below.

+		leds {
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_leds>, <&mpp_leds>;
+
+			compatible = "gpio-leds";
+
+			led@1 {
+				label = "dragonboard-600c:green:user1";
+				gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "heartbeat";
+				default-state = "off";
+			};
+
+			led@2 {
+				label = "dragonboard-600c:green:user2";
+				gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "mmc0";
+				default-state = "off";
+			};
+
+			led@3 {
+				label = "dragonboard-600c:green:user3";
+				gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "mmc1";
+				default-state = "off";
+			};
+
+			led@4 {
+				label = "apq8016-sbc:green:user4";
+				gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "none";
+				default-state = "off";
+			};
+
+			led@5 {
+				label = "dragonboard-600c:yellow:wlan";
+				gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "wlan";

This should either be "phy0rx", "phy0tx", "phy0assoc" or "phy0radio". TX
does not seem to work, so this should be debugged; "assoc" is probably
the one that makes most sense.


Am ok, to change, did you get activity leds works with any of these strings with WLAN or BT?

phy0rx/tx seems to be bit more generic and atleast the name looks bit non-specific to wlan.

These names should be documented somewhere, Its very difficult to find which names to use unless you read the code.

It would be nice to just provide a phandle to the device which led-trigger should use, which makes it clear and explicit.




+				default-state = "off";
+			};
+
+			led@6 {
+				label = "dragonboard-600c:blue:bt";
+				gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "bt";

This should be "hci0-power".

Does this trigger work for you?
Name is bit misleading though.

Thanks,
srini

+				default-state = "off";
+			};
+		};
+

Regards,
Bjorn

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux