Add support to enable/disable active discharge of regulator via machine constraints. This configuration is done when setting machine constraint during regulator register and if regulator driver implemented the callback ops. Signed-off-by: Laxman Dewangan <ldewangan@xxxxxxxxxx> --- drivers/regulator/core.c | 10 ++++++++++ drivers/regulator/of_regulator.c | 5 +++++ include/linux/regulator/driver.h | 3 +++ include/linux/regulator/machine.h | 4 ++++ 4 files changed, 22 insertions(+) diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c index 055f8c1..3e865b0 100644 --- a/drivers/regulator/core.c +++ b/drivers/regulator/core.c @@ -1139,6 +1139,16 @@ static int set_machine_constraints(struct regulator_dev *rdev, } } + if ((rdev->constraints->active_discharge >= 0) + && ops->set_active_discharge) { + ret = ops->set_active_discharge(rdev, + rdev->constraints->active_discharge); + if (ret < 0) { + rdev_err(rdev, "failed to set active discharge\n"); + return ret; + } + } + print_constraints(rdev); return 0; } diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c index 499e437..d1e0c03 100644 --- a/drivers/regulator/of_regulator.c +++ b/drivers/regulator/of_regulator.c @@ -93,6 +93,11 @@ static void of_get_regulation_constraints(struct device_node *np, constraints->soft_start = of_property_read_bool(np, "regulator-soft-start"); + ret = of_property_read_u32(np, "regulator-active-discharge", &pval); + if (!ret) + constraints->active_discharge = pval; + else + constraints->active_discharge = -1; if (!of_property_read_u32(np, "regulator-initial-mode", &pval)) { if (desc && desc->of_map_mode) { diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 16ac9e1..59dbaf7 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -93,6 +93,8 @@ struct regulator_linear_range { * @get_current_limit: Get the configured limit for a current-limited regulator. * @set_input_current_limit: Configure an input limit. * + * @set_active_discharge: Set active discharge enable/disable of regulators. + * * @set_mode: Set the configured operating mode for the regulator. * @get_mode: Get the configured operating mode for the regulator. * @get_status: Return actual (not as-configured) status of regulator, as a @@ -149,6 +151,7 @@ struct regulator_ops { int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); int (*set_over_current_protection) (struct regulator_dev *); + int (*set_active_discharge) (struct regulator_dev *, bool enable); /* enable/disable regulator */ int (*enable) (struct regulator_dev *); diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h index a1067d0..408cde7 100644 --- a/include/linux/regulator/machine.h +++ b/include/linux/regulator/machine.h @@ -100,6 +100,8 @@ struct regulator_state { * @initial_state: Suspend state to set by default. * @initial_mode: Mode to set at startup. * @ramp_delay: Time to settle down after voltage change (unit: uV/us) + * @active_discharge: Enable/disable active discharge. The values are: + * -1: Default, 0: Disable, 1: Enable. * @enable_time: Turn-on time of the rails (unit: microseconds) */ struct regulation_constraints { @@ -140,6 +142,8 @@ struct regulation_constraints { unsigned int ramp_delay; unsigned int enable_time; + int active_discharge; + /* constraint flags */ unsigned always_on:1; /* regulator never off when system is on */ unsigned boot_on:1; /* bootloader/firmware enabled regulator */ -- 2.1.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html