This patch adds support for the mcp23s18 which is very similar to
the mcp23s17. A couple of control bits are not the same.
Notable IOCON_HAEN (s17 only) & IOCON_INTCC. Which can be ignored.
Patch changes the following:
- Add mcp23s18 types.
- Always set mirror bit if the dts defines mcp23s18. regardless of type.
Mirror bit is ignored on 8 bit devices anyway.
- In mcp23s08_probe use chip.ngpio instead of logic based on type
to determine number of gpio lins to increment by. This is set
appropiately by the call to mcp23s08_probe_one.
- Add mcp23s18 to device tree documentation.
- Remove statement that irqs don't work for spi. They do.
Tested with mcp23s18.
Signed-off-by: Phil Reid <preid@xxxxxxxxxxxxxxxxx>
---
.../devicetree/bindings/gpio/gpio-mcp23s08.txt | 4 +---
drivers/gpio/gpio-mcp23s08.c | 19 +++++++++++++++----
2 files changed, 16 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
index f3332b9..c934106 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
@@ -10,6 +10,7 @@ Required properties:
- "microchip,mcp23s08" for 8 GPIO SPI version
- "microchip,mcp23s17" for 16 GPIO SPI version
+ - "microchip,mcp23s18" for 16 GPIO SPI version
- "microchip,mcp23008" for 8 GPIO I2C version or
- "microchip,mcp23017" for 16 GPIO I2C version of the chip
NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
@@ -43,9 +44,6 @@ Optional properties:
- first cell is the pin number
- second cell is used to specify flags.
- interrupt-controller: Marks the device node as a interrupt controller.
-NOTE: The interrupt functionality is only supported for i2c versions of the
-chips. The spi chips can also do the interrupts, but this is not supported by
-the linux driver yet.
Optional device specific properties:
- microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices
diff --git a/drivers/gpio/gpio-mcp23s08.c b/drivers/gpio/gpio-mcp23s08.c
index c767879..72521d9 100644
--- a/drivers/gpio/gpio-mcp23s08.c
+++ b/drivers/gpio/gpio-mcp23s08.c
@@ -31,6 +31,7 @@
#define MCP_TYPE_S17 1
#define MCP_TYPE_008 2
#define MCP_TYPE_017 3
+#define MCP_TYPE_S18 4
/* Registers are all 8 bits wide.
*
@@ -617,6 +618,12 @@ static int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev,
mcp->chip.ngpio = 16;
mcp->chip.label = "mcp23s17";
break;
+
+ case MCP_TYPE_S18:
+ mcp->ops = &mcp23s17_ops;
+ mcp->chip.ngpio = 16;
+ mcp->chip.label = "mcp23s18";
+ break;
#endif /* CONFIG_SPI_MASTER */
#if IS_ENABLED(CONFIG_I2C)
@@ -657,8 +664,7 @@ static int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev,
of_property_read_bool(mcp->chip.parent->of_node,
"microchip,irq-active-high");
- if (type == MCP_TYPE_017)
- mirror = pdata->mirror;
+ mirror = pdata->mirror;
}
if ((status & IOCON_SEQOP) || !(status & IOCON_HAEN) || mirror ||
@@ -735,6 +741,10 @@ static const struct of_device_id mcp23s08_spi_of_match[] = {
.compatible = "microchip,mcp23s17",
.data = (void *) MCP_TYPE_S17,
},
+ {
+ .compatible = "microchip,mcp23s18",
+ .data = (void *) MCP_TYPE_S18,
+ },
/* NOTE: The use of the mcp prefix is deprecated and will be removed. */
{
.compatible = "mcp,mcp23s08",
@@ -969,8 +979,8 @@ static int mcp23s08_probe(struct spi_device *spi)
goto fail;
if (pdata->base != -1)
- pdata->base += (type == MCP_TYPE_S17) ? 16 : 8;
- ngpio += (type == MCP_TYPE_S17) ? 16 : 8;
+ pdata->base += data->mcp[addr]->chip.ngpio;
+ ngpio += data->mcp[addr]->chip.ngpio;
}
data->ngpio = ngpio;
@@ -1012,6 +1022,7 @@ static int mcp23s08_remove(struct spi_device *spi)
static const struct spi_device_id mcp23s08_ids[] = {
{ "mcp23s08", MCP_TYPE_S08 },
{ "mcp23s17", MCP_TYPE_S17 },
+ { "mcp23s18", MCP_TYPE_S18 },
{ },
};
MODULE_DEVICE_TABLE(spi, mcp23s08_ids);
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
