Hi Jean-Michel,
Some minor comments below.
On 02/08/2016 12:20 PM, Jean-Michel Hautbois wrote:
> This device is a SPI based device from TI.
> It is a 3 Gbps HD/SD SDI Dual Output Low Power
> Extended Reach Adaptive Cable Equalizer.
>
> LMH0395 enables the use of up to two outputs.
> These can be configured using DT.
> The name gives the spi bus, and the CS associated.
> Example : lmh0395-1@spi2
> LMH0395 is on bus SPI2 with CS number 1.
>
> Controls should be accessible from userspace too.
> This will have to be done later.
>
> Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxxx>
> ---
> v2: Add DT support
> v3: Change the bit set/clear in output_type as disabled means 'set the bit'
> v4: Clearer description of endpoints usage in Doc, and some init changes.
> Add a dependency on OF and don't test CONFIG_OF anymore.
> v5: Change port description in Documentation
> Multiple ports : required #address-cells and #size-cells
> Alphabetical order for include files
> Simplify register set/clear
> Check device ID
> Implement log_status handler
> v6: Take Laurent Pinchart remarks into account
> Correct register settings
> Use next generation MC
>
> .../devicetree/bindings/media/spi/lmh0395.txt | 51 +++
> MAINTAINERS | 6 +
> drivers/media/Kconfig | 1 +
> drivers/media/Makefile | 2 +-
> drivers/media/spi/Kconfig | 15 +
> drivers/media/spi/Makefile | 1 +
> drivers/media/spi/lmh0395.c | 477 +++++++++++++++++++++
> drivers/media/spi/lmh039x.h | 55 +++
> 8 files changed, 607 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/devicetree/bindings/media/spi/lmh0395.txt
> create mode 100644 drivers/media/spi/Kconfig
> create mode 100644 drivers/media/spi/Makefile
> create mode 100644 drivers/media/spi/lmh0395.c
> create mode 100644 drivers/media/spi/lmh039x.h
>
> diff --git a/Documentation/devicetree/bindings/media/spi/lmh0395.txt b/Documentation/devicetree/bindings/media/spi/lmh0395.txt
> new file mode 100644
> index 0000000..5c6ab4a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/spi/lmh0395.txt
> @@ -0,0 +1,51 @@
> +* Texas Instruments lmh0395 3G HD/SD SDI equalizer
> +
> +"The LMH0395 is an SDI equalizer designed to extend the reach of SDI signals
> +transmitted over cable by equalizing the input signal and generating clean
> +outputs. It has one differential input and two differential output that can be
> +independently controlled."
> +
> +Required Properties :
> +- compatible: Must be "ti,lmh0395"
> +
> +The device node must contain one 'port' child node per device input and output
> +port, in accordance with the video interface bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +The LMH0395 has three ports numbered as follows.
> +
> + Port LMH0395
> +------------------------------------------------------------
> + SDI (SDI input) 0
> + SDO0 (SDI output 0) 1
> + SDO1 (SDI output 1) 2
> +
> +Example:
> +
> +ecspi@02010000 {
> + ...
> + ...
> +
> + lmh0395@1 {
> + compatible = "ti,lmh0395";
> + reg = <1>;
> + spi-max-frequency = <20000000>;
> + ports {
> + port@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + sdi0_in: endpoint {};
> + };
> + port@1 {
> + reg = <1>;
> + sdi0_out0: endpoint {};
> + };
> + port@2 {
> + reg = <2>;
> + /* endpoint not specified, disable output */
> + };
> + };
> + };
> + ...
> +};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 30aca4a..d155df5 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -10889,6 +10889,12 @@ S: Maintained
> F: sound/soc/codecs/lm49453*
> F: sound/soc/codecs/isabelle*
>
> +TI LMH0395 DRIVER
> +M: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxxx>
> +L: linux-media@xxxxxxxxxxxxxxx
> +S: Maintained
> +F: drivers/media/spi/lmh039*
> +
> TI LP855x BACKLIGHT DRIVER
> M: Milo Kim <milo.kim@xxxxxx>
> S: Maintained
> diff --git a/drivers/media/Kconfig b/drivers/media/Kconfig
> index a8518fb..4b38792 100644
> --- a/drivers/media/Kconfig
> +++ b/drivers/media/Kconfig
> @@ -213,6 +213,7 @@ config MEDIA_ATTACH
> default MODULES
>
> source "drivers/media/i2c/Kconfig"
> +source "drivers/media/spi/Kconfig"
> source "drivers/media/tuners/Kconfig"
> source "drivers/media/dvb-frontends/Kconfig"
>
> diff --git a/drivers/media/Makefile b/drivers/media/Makefile
> index e608bbc..6a64e96 100644
> --- a/drivers/media/Makefile
> +++ b/drivers/media/Makefile
> @@ -8,7 +8,7 @@ media-objs := media-device.o media-devnode.o media-entity.o
> # I2C drivers should come before other drivers, otherwise they'll fail
> # when compiled as builtin drivers
> #
> -obj-y += i2c/ tuners/
> +obj-y += i2c/ tuners/ spi/
> obj-$(CONFIG_DVB_CORE) += dvb-frontends/
>
> #
> diff --git a/drivers/media/spi/Kconfig b/drivers/media/spi/Kconfig
> new file mode 100644
> index 0000000..a9d06cb
> --- /dev/null
> +++ b/drivers/media/spi/Kconfig
> @@ -0,0 +1,15 @@
> +if VIDEO_V4L2
> +
> +config VIDEO_LMH0395
> + tristate "LMH0395 equalizer"
> + depends on VIDEO_V4L2 && SPI && VIDEO_V4L2_SUBDEV_API
> + depends on MEDIA_CONTROLLER && OF
> + ---help---
> + Support for TI LMH0395 3G HD/SD SDI Dual Output Low Power
> + Extended Reach Adaptive Cable Equalizer.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called lmh0395.
> +
> +
> +endif
> diff --git a/drivers/media/spi/Makefile b/drivers/media/spi/Makefile
> new file mode 100644
> index 0000000..6c587e5
> --- /dev/null
> +++ b/drivers/media/spi/Makefile
> @@ -0,0 +1 @@
> +obj-$(CONFIG_VIDEO_LMH0395) += lmh0395.o
> diff --git a/drivers/media/spi/lmh0395.c b/drivers/media/spi/lmh0395.c
> new file mode 100644
> index 0000000..bf6b52c
> --- /dev/null
> +++ b/drivers/media/spi/lmh0395.c
> @@ -0,0 +1,477 @@
> +/*
> + * LMH0395 SPI driver.
> + * Copyright (C) 2016 Jean-Michel Hautbois
> + *
> + * 3G HD/SD SDI Dual Output Low Power Extended Reach Adaptive Cable Equalizer
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/ioctl.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/types.h>
> +#include <linux/slab.h>
> +#include <linux/spi/spi.h>
> +#include <linux/uaccess.h>
> +#include <linux/videodev2.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-of.h>
> +#include "lmh039x.h"
> +
> +static const char * const lmh039x_output_strs[] = {
> + "No Output Driver",
> + "Output Driver 0",
> + "Output Driver 1",
> + "Output Driver 0+1",
> +};
> +
> +/* spi implementation */
> +
> +static int lmh0395_spi_write(struct spi_device *spi, u8 reg, u8 data)
> +{
> + int err;
> + u8 cmd[2];
> +
> + cmd[0] = LMH0395_SPI_CMD_WRITE | reg;
> + cmd[1] = data;
> +
> + err = spi_write(spi, cmd, 2);
> + if (err < 0) {
> + dev_err(&spi->dev, "SPI write failed : %d\n", err);
> + return err;
> + }
> +
> + return err;
> +}
> +
> +static int lmh0395_spi_read(struct spi_device *spi, u8 reg, unsigned long *data)
> +{
> + int err;
> + u8 cmd[2];
> + u8 read_data[2];
> +
> + cmd[0] = LMH0395_SPI_CMD_READ | reg;
> + cmd[1] = 0xff;
> +
> + err = spi_write(spi, cmd, 2);
> + if (err < 0) {
> + dev_err(&spi->dev, "SPI failed to select reg : %d\n", err);
> + return err;
> + }
> +
> + err = spi_read(spi, read_data, 2);
> + if (err < 0) {
> + dev_err(&spi->dev, "SPI failed to read reg : %d\n", err);
> + return err;
> + }
> + /* The first 8 bits is the address used, drop it */
> + *data = read_data[1];
> +
> + return err;
> +}
> +
> +struct lmh0395_state {
> + struct v4l2_subdev sd;
> + struct media_pad pads[LMH0395_PADS_NUM];
> + enum lmh0395_output_type output_type;
> +};
> +
> +static inline struct lmh0395_state *to_state(struct v4l2_subdev *sd)
> +{
> + return container_of(sd, struct lmh0395_state, sd);
> +}
> +
> +static bool lmh0395_carrier_detect(struct v4l2_subdev *sd)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + unsigned long reg;
> +
> + lmh0395_spi_read(spi, LMH0395_GENERAL_CTRL, ®);
> +
> + if (reg & 0x80)
> + return true;
> + else
> + return false;
Just do:
return (reg & 0x80) ? true : false;
> +}
> +
> +static int lmh0395_get_rate(struct v4l2_subdev *sd, u8 *rate)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + int err;
> + unsigned long ctrl;
> +
> + if (!lmh0395_carrier_detect(sd))
> + return 0;
> +
> + err = lmh0395_spi_read(spi, LMH0395_RATE_INDICATOR, &ctrl);
> + if (err < 0)
> + return err;
> +
> + *rate = ctrl & 0x20;
> + dev_dbg(&spi->dev, "Rate : %s\n", (ctrl & 0x20) ? "3G/HD" : "SD");
> + return 0;
> +}
> +
> +static int lmh0395_get_launch_amp(struct v4l2_subdev *sd)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + unsigned long reg;
> + int launch_amp;
> + int err;
> +
> + err = lmh0395_spi_read(spi, LMH0395_LAUNCH_AMP_INDICATION, ®);
> + if (err < 0)
> + return err;
> +
> + launch_amp = ((reg & 0xfc) >> 2);
No need for the outer parenthesis.
> + launch_amp = launch_amp - 32;
> +
> + dev_dbg(&spi->dev, "Launch amplitude : %d\n", launch_amp);
> +
> + return launch_amp;
> +}
> +
> +static int lmh0395_get_cable_length(struct v4l2_subdev *sd, u8 rate)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + u8 length;
> + unsigned long cli;
> + int err;
> +
> + err = lmh0395_spi_read(spi, LMH0395_CABLE_LENGTH_INDICATOR, &cli);
> + if (err < 0)
> + return err;
> +
> + /* The cable length indicator (CLI) provides an indication of the
> + * length of the cable attached to input. CLI is accessible via bits
> + * [7:0] of SPI register 06h.
> + * The 8-bit setting ranges in decimal value from 0 to 247
> + * ("00000000" to "11110111" binary), corresponding to 0 to 400m of
> + * Belden 1694A cable.
> + * For 3G and HD input, CLI is 1.25m per step.
> + * For SD input, CLI is 1.25m per step, less 20m, from 0 to 191 decimal
> + * and 3.5m per step from 192 to 247 decimal.
> + */
> +
> + length = cli*5/4;
> + if (rate == 0) {
> + if (cli <= 191)
> + length -= 20;
> + else
> + length = ((191*5/4)-20) + ((cli-191)*7/2);
> +
> + }
> + dev_dbg(&spi->dev, "Length estimated (BELDEN 1694A cables) : %dm\n",
> + length);
> + return length;
> +}
> +
> +static int lmh0395_set_output_type(struct v4l2_subdev *sd, unsigned long output)
> +{
> + struct lmh0395_state *state = to_state(sd);
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + unsigned long muteref_reg;
> +
> + /* Get the current register status */
> + lmh0395_spi_read(spi, LMH0395_MUTE_REF, &muteref_reg);
> + switch (output) {
> + case LMH0395_OUTPUT_TYPE_SDO0:
> + clear_bit(6, &muteref_reg);
> + break;
> + case LMH0395_OUTPUT_TYPE_SDO1:
> + clear_bit(7, &muteref_reg);
> + break;
> + case LMH0395_OUTPUT_TYPE_BOTH:
> + clear_bit(6, &muteref_reg);
> + clear_bit(7, &muteref_reg);
> + break;
> + case LMH0395_OUTPUT_TYPE_NONE:
> + set_bit(6, &muteref_reg);
> + set_bit(7, &muteref_reg);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + state->output_type = output;
> + return 0;
> +
> +}
> +
> +static int lmh0395_get_control(struct v4l2_subdev *sd)
> +{
> + int err;
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + unsigned long ctrl;
> + u8 rate = 0;
> +
> + err = lmh0395_spi_read(spi, LMH0395_GENERAL_CTRL, &ctrl);
> + if (err < 0)
> + return err;
> +
> + if (ctrl & 0x80) {
> + dev_dbg(&spi->dev, "Carrier detected\n");
> + lmh0395_get_rate(sd, &rate);
> + lmh0395_get_cable_length(sd, rate);
> + lmh0395_get_launch_amp(sd);
> + }
> + return 0;
> +}
> +
> +static int lmh0395_get_output_status(struct v4l2_subdev *sd)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + unsigned long muteref_reg;
> +
> + /* Get the current register status */
> + lmh0395_spi_read(spi, LMH0395_MUTE_REF, &muteref_reg);
> + dev_dbg(&spi->dev, "Output 0 is %s\n",
> + test_bit(7, &muteref_reg) ? "enabled" : "disabled");
> + dev_dbg(&spi->dev, "Output 1 is %s\n",
> + test_bit(6, &muteref_reg) ? "enabled" : "disabled");
> + return 0;
> +}
> +
> +static int lmh0395_log_status(struct v4l2_subdev *sd)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> +
> + dev_dbg(&spi->dev, "-----Chip status-----\n");
> + lmh0395_get_output_status(sd);
> + lmh0395_get_control(sd);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_VIDEO_ADV_DEBUG
> +static int lmh0395_g_register(struct v4l2_subdev *sd,
> + struct v4l2_dbg_register *reg)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + int err = 0;
> + unsigned long val;
> +
> + reg->size = 1;
> + reg->val = 0;
> +
> + /* Don't try to access over last register */
> + if (reg->reg > LMH0395_LAUNCH_AMP_INDICATION)
> + return 0;
> +
> + err = lmh0395_spi_read(spi, reg->reg, &val);
> + if (!err)
> + reg->val = val;
> +
> + return err;
> +}
> +static int lmh0395_s_register(struct v4l2_subdev *sd,
> + const struct v4l2_dbg_register *reg)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> + int err = 0;
> +
> + /* Don't try to access over last register */
> + if (reg->reg > LMH0395_LAUNCH_AMP_INDICATION)
> + return -EINVAL;
> +
> + err = lmh0395_spi_write(spi, reg->reg, reg->val);
Just do return lmh0395_spi_write and you can drop the 'err' variable.
> +
> + return err;
> +}
> +#endif
> +
> +static int lmh0395_s_routing(struct v4l2_subdev *sd, u32 input, u32 output,
> + u32 config)
> +{
> + struct lmh0395_state *state = to_state(sd);
> +
> + if (state->output_type == output)
> + return 0;
> +
> + return lmh0395_set_output_type(sd, output);
> +}
> +
> +static int lmh0395_registered(struct v4l2_subdev *sd)
> +{
> + struct spi_device *spi = v4l2_get_subdevdata(sd);
> +
> + dev_dbg(&spi->dev, "subdev registered\n");
> + lmh0395_set_output_type(sd, LMH0395_OUTPUT_TYPE_BOTH);
> +
> + return 0;
> +}
> +
> +static const struct v4l2_subdev_internal_ops lmh0395_internal_ops = {
> + .registered = lmh0395_registered,
> +};
> +
> +static const struct v4l2_subdev_video_ops lmh0395_video_ops = {
> + .s_routing = lmh0395_s_routing,
> +};
> +
> +static const struct v4l2_subdev_core_ops lmh0395_core_ops = {
> + .log_status = lmh0395_log_status,
> +#ifdef CONFIG_VIDEO_ADV_DEBUG
> + .g_register = lmh0395_g_register,
> + .s_register = lmh0395_s_register,
> +#endif
> +};
> +
> +static const struct v4l2_subdev_ops lmh0395_ops = {
> + .core = &lmh0395_core_ops,
> + .video = &lmh0395_video_ops,
> +};
> +
> +struct lmh0395_dev {
> + unsigned long dev_id;
> + char *name;
> +};
> +
> +static const struct lmh0395_dev lmh0395_dev[] = {
> + {
> + .dev_id = ID_LMH0384,
> + .name = "LMH0384",
> + },
> + {
> + .dev_id = ID_LMH0394,
> + .name = "LMH0394",
> + },
> + {
> + .dev_id = ID_LMH0395,
> + .name = "LMH0395",
> + },
> + { /* sentinel */ },
> +};
> +
> +static const struct spi_device_id lmh0395_id[] = {
> + { "lmh0395", 0 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(spi, lmh0395_id);
> +
> +static const struct of_device_id lmh0395_of_match[] = {
> + {.compatible = "ti,lmh0395", },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, lmh0395_of_match);
> +
> +static int lmh0395_probe(struct spi_device *spi)
> +{
> + unsigned long device_id;
> + struct lmh0395_state *state;
> + struct v4l2_subdev *sd;
> + int err, i;
> + struct device_node *n = NULL;
> + struct of_endpoint ep;
> +
> + err = lmh0395_spi_read(spi, LMH0395_DEVICE_ID, &device_id);
> + if (err < 0)
> + return err;
> +
> + for (i = 0 ; i < ARRAY_SIZE(lmh0395_dev) ; i++) {
No space before ';'.
> + if (device_id == lmh0395_dev[i].dev_id)
> + break;
> + }
> + if (i == ARRAY_SIZE(lmh0395_dev)) {
> + dev_err(&spi->dev, "Device not supported (id = %08lx)\n",
> + device_id);
> + return -ENODEV;
> + }
> + dev_dbg(&spi->dev, "%s detected\n", lmh0395_dev[i].name);
> +
> + /* Now that the device is here, let's init V4L2 */
> + state = devm_kzalloc(&spi->dev, sizeof(*state), GFP_KERNEL);
> + if (!state)
> + return -ENOMEM;
> +
> + sd = &state->sd;
> +
> + if (spi->dev.of_node) {
> + dev_dbg(&spi->dev, "Parsing DT configuration\n");
> + while ((n = of_graph_get_next_endpoint(spi->dev.of_node, n))
> + != NULL) {
> + err = of_graph_parse_endpoint(n, &ep);
> + if (err < 0) {
> + dev_err(&spi->dev, "Could not parse endpoint: %d\n", err);
> + of_node_put(n);
> + return err;
> + }
> + dev_dbg(&spi->dev, "endpoint %d on port %d\n",
> + ep.id, ep.port);
> + of_node_put(n);
> + }
> + } else {
> + dev_dbg(&spi->dev, "No DT configuration\n");
> + }
> +
> + v4l2_spi_subdev_init(sd, spi, &lmh0395_ops);
> + sd->internal_ops = &lmh0395_internal_ops;
> +
> + snprintf(sd->name, sizeof(sd->name), "%s-%d@spi%d",
> + spi->dev.driver->name,
> + spi->chip_select,
> + spi->master->bus_num);
> + dev_dbg(&spi->dev, "%s named %s\n", lmh0395_dev[i].name, sd->name);
> +
> + state->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> + state->pads[LMH0395_SDI_INPUT].flags = MEDIA_PAD_FL_SINK;
> + state->pads[LMH0395_SDI_OUT0].flags = MEDIA_PAD_FL_SOURCE;
> + state->pads[LMH0395_SDI_OUT1].flags = MEDIA_PAD_FL_SOURCE;
> +
> + err = media_entity_pads_init(&sd->entity,
> + LMH0395_PADS_NUM, state->pads);
> + if (err) {
> + dev_err(&spi->dev, "entity init failed\n");
> + spi_unregister_device(spi);
> + return err;
> + }
> +
> + dev_dbg(&spi->dev, "Entity initialized\n");
> +
> + err = v4l2_async_register_subdev(sd);
> + if (err < 0) {
> + media_entity_cleanup(&sd->entity);
> + spi_unregister_device(spi);
> + return err;
> + }
> +
> + dev_dbg(&spi->dev, "device probed\n");
> +
> + return 0;
> +}
> +
> +static int lmh0395_remove(struct spi_device *spi)
> +{
> + struct v4l2_subdev *sd = spi_get_drvdata(spi);
> +
> + v4l2_async_unregister_subdev(sd);
> + media_entity_cleanup(&sd->entity);
> + spi_unregister_device(spi);
> + return 0;
> +}
> +
> +static struct spi_driver lmh0395_driver = {
> + .driver = {
> + .of_match_table = lmh0395_of_match,
> + .name = "lmh0395",
> + .owner = THIS_MODULE,
> + },
> + .probe = lmh0395_probe,
> + .remove = lmh0395_remove,
> + .id_table = lmh0395_id,
> +};
> +
> +module_spi_driver(lmh0395_driver);
> +
> +MODULE_DESCRIPTION("spi device driver for LMH0395 equalizer");
> +MODULE_AUTHOR("Jean-Michel Hautbois");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/media/spi/lmh039x.h b/drivers/media/spi/lmh039x.h
> new file mode 100644
> index 0000000..f3e35e4
> --- /dev/null
> +++ b/drivers/media/spi/lmh039x.h
> @@ -0,0 +1,55 @@
> +/*
> + * LMH0395 SPI driver.
> + * Copyright (C) 2014 Jean-Michel Hautbois
> + *
> + * 3G HD/SD SDI Dual Output Low Power Extended Reach Adaptive Cable Equalizer
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _LMH039X_
> +#define _LMH039X_
> +
> +#include <media/v4l2-device.h>
> +
> +#define LMH0395_SPI_CMD_WRITE 0x00
> +#define LMH0395_SPI_CMD_READ 0x80
> +
> +/* Registers of LMH0395 */
> +#define LMH0395_GENERAL_CTRL 0x00
> +#define LMH0395_OUTPUT_DRIVER 0x01
> +#define LMH0395_LAUNCH_AMP_CTRL 0x02
> +#define LMH0395_MUTE_REF 0x03
> +#define LMH0395_DEVICE_ID 0x04
> +#define LMH0395_RATE_INDICATOR 0x05
> +#define LMH0395_CABLE_LENGTH_INDICATOR 0x06
> +#define LMH0395_LAUNCH_AMP_INDICATION 0x07
> +
> +/* This is a one input, dual output device */
> +#define LMH0395_SDI_INPUT 0
> +#define LMH0395_SDI_OUT0 1
> +#define LMH0395_SDI_OUT1 2
> +
> +#define LMH0395_PADS_NUM 3
> +
> +#define ID_LMH0384 0x03
> +#define ID_LMH0394 0x13
> +#define ID_LMH0395 0x23
> +
> +/* Register LMH0395_MUTE_REF bits [7:6] */
> +enum lmh0395_output_type {
> + LMH0395_OUTPUT_TYPE_NONE,
> + LMH0395_OUTPUT_TYPE_SDO0,
> + LMH0395_OUTPUT_TYPE_SDO1,
> + LMH0395_OUTPUT_TYPE_BOTH
> +};
> +
> +#endif
>
Regards,
Hans
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
