Maxim Semiconductor's PMIC MAX77620/MAX20024 has 8 GPIO pins which act as GPIO as well as special function mode. Add DT binding document to configure pins in function mode as well as pin configuration parameters. Signed-off-by: Laxman Dewangan <ldewangan@xxxxxxxxxx> Acked-by: Rob Herring <robh@xxxxxxxxxx> --- Changes from V4: - Separate out from pincontrol driver Changes from V5: - Starting patch title with pinctrl instead of DT:pinctrl Changes from V6/V7: - None .../bindings/pinctrl/pinctrl-max77620.txt | 127 +++++++++++++++++++++ 1 file changed, 127 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt new file mode 100644 index 0000000..ad4fce3 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt @@ -0,0 +1,127 @@ +Pincontrol driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt> +for details of the common pinctrl bindings used by client devices, +including the meaning of the phrase "pin configuration node". + +Optional Pinmux properties: +-------------------------- +Following properties are required if default setting of pins are required +at boot. +- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per + <pinctrl-binding.txt>. + +The pin configurations are defined as child of the pinctrl states node. Each +sub-node have following properties: + +Required properties: +------------------ +- pins: List of pins. Valid values of pins properties are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7. + +Optional properties: +------------------- +Following are optional properties defined as pinmux DT binding document +<pinctrl-bindings.txt>. Absence of properties will leave the configuration +on default. + function, + drive-push-pull, + drive-open-drain, + bias-pull-up, + bias-pull-down. + +Valid values for function properties are: + gpio, lpm-control-in, fps-out, 32k-out, sd0-dvs-in, sd1-dvs-in, + reference-out + +Theres is also customised properties for the GPIO1, GPIO2 and GPIO3. These +customised properties are required to configure FPS configuration parameters +of these GPIOs. Please refer <devicetree/bindings/mfd/max77620.txt> for more +detail of Flexible Power Sequence (FPS). + +- maxim,active-fps-source: FPS source for the GPIOs to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + GPIO is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + GPIO to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the GPIO get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the GPIO get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + + pinctrl-names = "default"; + pinctrl-0 = <&spmic_default>; + + spmic_default: pinmux@0 { + pin_gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + pin_gpio1 { + pins = "gpio1"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + pin_gpio2 { + pins = "gpio2"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + }; +}; -- 2.1.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html