From: David Daney <david.daney@xxxxxxxxxx>
The cavium,pci-thunder-ecam devices are exactly ECAM based PCI root
complexes. These root complexes (loosely referred to as ECAM units in
the hardware manuals) are used to access the Thunder on-chips devices.
They are special in that all the BARs on devices behind these root
complexes are at fixed addresses. To handle this in a manner
compatible with the core PCI code, we have the config access functions
synthesize Enhanced Allocation (EA) capability entries for each BAR.
Since this EA synthesis is needed for exactly one chip model, we can
hard code some assumptions about the device topology and the
properties of specific DEVFNs in the driver.
Signed-off-by: David Daney <david.daney@xxxxxxxxxx>
---
.../devicetree/bindings/pci/pci-thunder-ecam.txt | 30 ++
drivers/pci/host/Kconfig | 7 +
drivers/pci/host/Makefile | 1 +
drivers/pci/host/pci-thunder-ecam.c | 358 +++++++++++++++++++++
4 files changed, 396 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt
create mode 100644 drivers/pci/host/pci-thunder-ecam.c
diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt
new file mode 100644
index 0000000..34658f2
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt
@@ -0,0 +1,30 @@
+* ThunderX PCI host controller for pass-1.x silicon
+
+Firmware-initialized PCI host controller to on-chip devices found on
+some Cavium ThunderX processors. These devices have ECAM based config
+access, but the BARs are all at fixed addresses. We handle the fixed
+addresses by synthesizing Enhanced Allocation (EA) capabilities for
+these devices.
+
+The properties and their meanings are identical to those described in
+host-generic-pci.txt except as listed below.
+
+Properties of the host controller node that differ from
+host-generic-pci.txt:
+
+- compatible : Must be "cavium,pci-host-thunder-ecam"
+
+Example:
+
+ pci@84b0,00000000 {
+ compatible = "cavium,pci-host-thunder-ecam";
+ device_type = "pci";
+ msi-parent = <&its>;
+ msi-map = <0 &its 0x30000 0x10000>;
+ bus-range = <0 31>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ #stream-id-cells = <1>;
+ reg = <0x84b0 0x00000000 0 0x02000000>; /* Configuration space */
+ ranges = <0x03000000 0x8180 0x00000000 0x8180 0x00000000 0x80 0x00000000>; /* mem ranges */
+ };
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index 184df22..f8912c6 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -202,4 +202,11 @@ config PCI_HOST_THUNDER_PEM
help
Say Y here if you want PCIe support for CN88XX Cavium Thunder SoCs.
+config PCI_HOST_THUNDER_ECAM
+ bool "Cavium Thunder ECAMe controller to on-chip devices on pass-1.x silicon"
+ depends on OF && ARM64
+ select PCI_HOST_COMMON
+ help
+ Say Y here if you want ECAM support for CN88XX-Pass-1.x Cavium Thunder SoCs.
+
endmenu
diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
index 8903172..d6af3ba 100644
--- a/drivers/pci/host/Makefile
+++ b/drivers/pci/host/Makefile
@@ -23,4 +23,5 @@ obj-$(CONFIG_PCIE_ALTERA) += pcie-altera.o
obj-$(CONFIG_PCIE_ALTERA_MSI) += pcie-altera-msi.o
obj-$(CONFIG_PCI_HISI) += pcie-hisi.o
obj-$(CONFIG_PCIE_QCOM) += pcie-qcom.o
+obj-$(CONFIG_PCI_HOST_THUNDER_ECAM) += pci-thunder-ecam.o
obj-$(CONFIG_PCI_HOST_THUNDER_PEM) += pci-thunder-pem.o
diff --git a/drivers/pci/host/pci-thunder-ecam.c b/drivers/pci/host/pci-thunder-ecam.c
new file mode 100644
index 0000000..83ee590
--- /dev/null
+++ b/drivers/pci/host/pci-thunder-ecam.c
@@ -0,0 +1,358 @@
+/*
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2015 Cavium, Inc.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/of_pci.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include "pci-host-common.h"
+
+/* Mapping is standard ECAM */
+static void __iomem *thunder_ecam_map_bus(struct pci_bus *bus,
+ unsigned int devfn,
+ int where)
+{
+ struct gen_pci *pci = bus->sysdata;
+ resource_size_t idx = bus->number - pci->cfg.bus_range->start;
+
+ return pci->cfg.win[idx] + ((devfn << 12) | where);
+}
+
+static void set_val(u32 v, int where, int size, u32 *val)
+{
+ int shift = (where & 3) * 8;
+
+ pr_debug("set_val %04x: %08x\n", (unsigned)(where & ~3), v);
+ v >>= shift;
+ if (size == 1)
+ v &= 0xff;
+ else if (size == 2)
+ v &= 0xffff;
+ *val = v;
+}
+
+static int handle_ea_bar(u32 e0, int bar, struct pci_bus *bus,
+ unsigned int devfn, int where, int size, u32 *val)
+{
+ void __iomem *addr;
+ u32 v;
+ /*
+ * Each entry is 16-byte aligned bits[2,3] select which word
+ * in the entry
+ */
+ int where_a = where & 0xc;
+
+ if (where_a == 0) {
+ set_val(e0, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0x4) {
+ addr = bus->ops->map_bus(bus, devfn, bar); /* BAR 0 */
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+ v = readl(addr);
+ v &= ~0xf;
+ v |= 2; /* EA entry-1. Base-L */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0x8) {
+ u32 barl_orig;
+ u32 barl_rb;
+
+ addr = bus->ops->map_bus(bus, devfn, bar); /* BAR 0 */
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+ barl_orig = readl(addr + 0);
+ writel(0xffffffff, addr + 0);
+ barl_rb = readl(addr + 0);
+ writel(barl_orig, addr + 0);
+ /* zeros in unsettable bits. */
+ v = ~barl_rb & ~3;
+ v |= 0xc; /* EA entry-2. Offset-L */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xc) {
+ addr = bus->ops->map_bus(bus, devfn, bar + 4); /* BAR 1 */
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+ v = readl(addr); /* EA entry-3. Base-H */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+static int thunder_ecam_config_read(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *val)
+{
+ u32 v;
+ u32 vendor_device;
+ void __iomem *addr;
+ int cfg_type;
+ int where_a = where & ~3;
+
+
+ addr = bus->ops->map_bus(bus, devfn, 0xc);
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+
+ v = readl(addr);
+
+ /* Check for non type-00 header. */
+ cfg_type = (v >> 16) & 0x7f;
+
+ /*
+ * All BARs have fixed addresses specified by the EA
+ * capability, they must return zero on read.
+ */
+ if (cfg_type == 0 &&
+ ((where >= 0x10 && where < 0x2c) ||
+ (where >= 0x1a4 && where < 0x1bc))) {
+ /* BAR or SRIOV BAR */
+ *val = 0;
+ return PCIBIOS_SUCCESSFUL;
+ }
+
+ addr = bus->ops->map_bus(bus, devfn, 0);
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+
+ vendor_device = readl(addr);
+ if (vendor_device == 0xffffffff)
+ goto no_emulation;
+
+ addr = bus->ops->map_bus(bus, devfn, 8);
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+
+ v = readl(addr);
+ if (v == 0xffffffff)
+ goto no_emulation;
+
+ pr_debug("%04x:%04x - Fix pass#: %08x, where: %03x, devfn: %03x\n",
+ vendor_device & 0xffff, vendor_device >> 16, v,
+ (unsigned) where, devfn);
+
+ /* Check for non type-00 header. */
+ if (cfg_type == 0) {
+ bool has_msix;
+ bool is_nic = (vendor_device == 0xa01e177d);
+ bool is_tns = (vendor_device == 0xa01f177d);
+
+ addr = bus->ops->map_bus(bus, devfn, 0x70);
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+ /* E_CAP */
+ v = readl(addr);
+ has_msix = (v & 0xff00) != 0;
+
+ if (!has_msix && where_a == 0x70) {
+ v |= 0xbc00; /* next capability is EA at 0xbc */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xb0) {
+ addr = bus->ops->map_bus(bus, devfn, where_a);
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+ v = readl(addr);
+ if (v & 0xff00)
+ pr_err("Bad MSIX cap header: %08x\n", v);
+ v |= 0xbc00; /* next capability is EA at 0xbc */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xbc) {
+ if (is_nic)
+ v = 0x40014; /* EA last in chain, 4 entries. */
+ else if (is_tns)
+ v = 0x30014; /* EA last in chain, 3 entries. */
+ else if (has_msix)
+ v = 0x20014; /* EA last in chain, 2 entries. */
+ else
+ v = 0x10014; /* EA last in chain, 1 entry. */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a >= 0xc0 && where_a < 0xd0)
+ /* EA entry-0. PP=0, BAR0 Size:3 */
+ return handle_ea_bar(0x80ff0003,
+ 0x10, bus, devfn, where,
+ size, val);
+ if (where_a >= 0xd0 && where_a < 0xe0 && has_msix)
+ /* EA entry-1. PP=0, BAR4 Size:3 */
+ return handle_ea_bar(0x80ff0043,
+ 0x20, bus, devfn, where,
+ size, val);
+ if (where_a >= 0xe0 && where_a < 0xf0 && is_tns)
+ /* EA entry-2. PP=0, BAR2, Size:3 */
+ return handle_ea_bar(0x80ff0023,
+ 0x18, bus, devfn, where,
+ size, val);
+ if (where_a >= 0xe0 && where_a < 0xf0 && is_nic)
+ /* EA entry-2. PP=4, VF_BAR0 (9), Size:3 */
+ return handle_ea_bar(0x80ff0493,
+ 0x1a4, bus, devfn, where,
+ size, val);
+ if (where_a >= 0xf0 && where_a < 0x100 && is_nic)
+ /* EA entry-3. PP=4, VF_BAR4 (d), Size:3 */
+ return handle_ea_bar(0x80ff04d3,
+ 0x1b4, bus, devfn, where,
+ size, val);
+ } else if (cfg_type == 1) {
+ bool is_rsl_bridge = devfn == 0x08;
+ bool is_rad_bridge = devfn == 0xa0;
+ bool is_zip_bridge = devfn == 0xa8;
+ bool is_dfa_bridge = devfn == 0xb0;
+ bool is_nic_bridge = devfn == 0x10;
+
+ if (where_a == 0x70) {
+ addr = bus->ops->map_bus(bus, devfn, where_a);
+ if (!addr) {
+ *val = ~0;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+ v = readl(addr);
+ if (v & 0xff00)
+ pr_err("Bad PCIe cap header: %08x\n", v);
+ v |= 0xbc00; /* next capability is EA at 0xbc */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xbc) {
+ if (is_nic_bridge)
+ v = 0x10014; /* EA last in chain, 1 entry */
+ else
+ v = 0x00014; /* EA last in chain, no entries */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xc0) {
+ if (is_rsl_bridge || is_nic_bridge)
+ v = 0x0101; /* subordinate:secondary = 1:1 */
+ else if (is_rad_bridge)
+ v = 0x0202; /* subordinate:secondary = 2:2 */
+ else if (is_zip_bridge)
+ v = 0x0303; /* subordinate:secondary = 3:3 */
+ else if (is_dfa_bridge)
+ v = 0x0404; /* subordinate:secondary = 4:4 */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xc4 && is_nic_bridge) {
+ /* Enabled, not-Write, SP=ff, PP=05, BEI=6, ES=4 */
+ v = 0x80ff0564;
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xc8 && is_nic_bridge) {
+ v = 0x00000002; /* Base-L 64-bit */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xcc && is_nic_bridge) {
+ v = 0xfffffffe; /* MaxOffset-L 64-bit */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xd0 && is_nic_bridge) {
+ v = 0x00008430; /* NIC Base-H */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ if (where_a == 0xd4 && is_nic_bridge) {
+ v = 0x0000000f; /* MaxOffset-H */
+ set_val(v, where, size, val);
+ return PCIBIOS_SUCCESSFUL;
+ }
+ }
+no_emulation:
+ return pci_generic_config_read(bus, devfn, where, size, val);
+}
+
+static int thunder_ecam_config_write(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 val)
+{
+ /*
+ * All BARs have fixed addresses, ignore BAR writes so they
+ * don't get corrupted.
+ */
+ if ((where >= 0x10 && where < 0x2c) ||
+ (where >= 0x1a4 && where < 0x1bc))
+ /* BAR or SRIOV BAR */
+ return PCIBIOS_SUCCESSFUL;
+
+ return pci_generic_config_write(bus, devfn, where, size, val);
+}
+
+static struct gen_pci_cfg_bus_ops thunder_ecam_bus_ops = {
+ .bus_shift = 20,
+ .ops = {
+ .map_bus = thunder_ecam_map_bus,
+ .read = thunder_ecam_config_read,
+ .write = thunder_ecam_config_write,
+ }
+};
+
+static const struct of_device_id thunder_ecam_of_match[] = {
+ { .compatible = "cavium,pci-host-thunder-ecam",
+ .data = &thunder_ecam_bus_ops },
+
+ { },
+};
+MODULE_DEVICE_TABLE(of, thunder_ecam_of_match);
+
+static int thunder_ecam_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct of_device_id *of_id;
+ struct gen_pci *pci = devm_kzalloc(dev, sizeof(*pci), GFP_KERNEL);
+
+ if (!pci)
+ return -ENOMEM;
+
+ of_id = of_match_node(thunder_ecam_of_match, dev->of_node);
+ pci->cfg.ops = (struct gen_pci_cfg_bus_ops *)of_id->data;
+
+ return pci_host_common_probe(pdev, pci);
+}
+
+static struct platform_driver thunder_ecam_driver = {
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .of_match_table = thunder_ecam_of_match,
+ },
+ .probe = thunder_ecam_probe,
+};
+module_platform_driver(thunder_ecam_driver);
+
+MODULE_DESCRIPTION("Thunder ECAM PCI host driver");
+MODULE_LICENSE("GPL v2");
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
