From: Petr Štetiar <ynezz@xxxxxxx> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@xxxxxxxxxxx> Signed-off-by: Petr Štetiar <ynezz@xxxxxxx> Reviewed-by: Stefan Agner <stefan@xxxxxxxx> --- Changes in v5: - drop iomux/pinctrl function container node as suggested by Shawn - added new line between nodes as suggested by Shawn - use consistent pinctrl group node naming schema xxxgrp as suggested by Shawn - replace the gpio-key,wakeup property with the generic wakeup-source one as suggested by Shawn - drop regulators function container node and use simple label reference to enable USB VBUS' as suggested by Shawn Changes in v4: None Changes in v3: - integrated review feedback from Petr - integrated review feedback from Stefan - fix comment concerning Apalis GPIO usage as GPIO7 is only used for PCIe switch reset on Apalis Evaluation board - move I2C DDC handling into carrier board DTS where it belongs - simplify RTC alias Changes in v2: - clarify exact Apalis iMX6Q/D SoM type in cover letter - clarify exact Apalis iMX6Q/D module type and Ixora carrier board in model node - got rid of obsolete mmc aliases - working SGTL5000 audio/sound integration - working STMPE811 touch screen controller integration - integrated review feedback from Lucas - left and even added some more comments as I don't see why putting any explanatory comments in dts' should be such a bad thing to do - completely got rid of the memory node as that is something typically filled in by the boot loader e.g. U-Boot - without the regulators simple-bus it no longer boots - even though we supposedly shipped a few hundred V1.0a modules drop DCE UART support for now and simplify file layout - replaced obsolete no-1-8-v by mainline supported voltage-ranges = <3300 3300> usdhc property and yes card detects are indeed active low (;-p) - integrated review feedback from Stefan - fixed Ethernet PHY reset & interrupt (requires Micrel PHY driver to be enabled) - fixed HDMI DDC (requires GPIO-based bitbanging I2C to be enabled) - fixed SPDIF arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-apalis-ixora.dts | 272 +++++++++++++++++++++++++++++++ 2 files changed, 273 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-apalis-ixora.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 150f801..4cc9adf 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -321,6 +321,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-udoo.dtb \ imx6dl-wandboard.dtb \ imx6dl-wandboard-revb1.dtb \ + imx6q-apalis-ixora.dtb \ imx6q-apf6dev.dtb \ imx6q-arm2.dtb \ imx6q-cm-fx6.dtb \ diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora.dts b/arch/arm/boot/dts/imx6q-apalis-ixora.dts new file mode 100644 index 0000000..2cba82d --- /dev/null +++ b/arch/arm/boot/dts/imx6q-apalis-ixora.dts @@ -0,0 +1,272 @@ +/* + * Copyright 2014-2016 Toradex AG + * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include "imx6q.dtsi" +#include "imx6qdl-apalis.dtsi" + +/ { + model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board"; + compatible = "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q", + "fsl,imx6q"; + + aliases { + i2c0 = &i2cddc; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + }; + + aliases { + rtc0 = &rtc_i2c; + rtc1 = &snvs_rtc; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + wakeup { + label = "Wake-Up"; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WAKEUP>; + debounce-interval = <10>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds_ixora>; + + led4-green { + label = "LED_4_GREEN"; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + }; + + led4-red { + label = "LED_4_RED"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + }; + + led5-green { + label = "LED_5_GREEN"; + gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; + }; + + led5-red { + label = "LED_5_RED"; + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; + }; + }; + + pwmleds { + compatible = "pwm-leds"; + + ledpwm1 { + label = "PWM1"; + pwms = <&pwm1 0 50000>; + max-brightness = <255>; + }; + + ledpwm2 { + label = "PWM2"; + pwms = <&pwm2 0 50000>; + max-brightness = <255>; + }; + + ledpwm3 { + label = "PWM3"; + pwms = <&pwm3 0 50000>; + max-brightness = <255>; + }; + }; +}; + +&backlight { + brightness-levels = <0 127 191 223 239 247 251 255>; + default-brightness-level = <1>; + status = "okay"; +}; + +&can1 { + status = "okay"; +}; + +&can2 { + status = "okay"; +}; + +&hdmi { + ddc-i2c-bus = <&i2cddc>; + status = "okay"; +}; + +&i2cddc { + status = "okay"; +}; + +/* GEN1_I2C: I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */ +&i2c1 { + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + + /* M41T0M6 real time clock on carrier board */ + rtc_i2c: rtc@68 { + compatible = "st,m41t00"; + reg = <0x68>; + }; +}; + +&ldb { + status = "okay"; +}; + +&pcie { + /* active-low meaning opposite of regular PERST# active-low polarity */ + reset-gpio = <&gpio1 28 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&pwm1 { + status = "okay"; +}; + +&pwm2 { + status = "okay"; +}; + +&pwm3 { + status = "okay"; +}; + +&pwm4 { + status = "okay"; +}; + +®_usb_otg_vbus { + status = "okay"; +}; + +®_usb_host_vbus { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&sound_spdif { + status = "okay"; +}; + +&spdif { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_host_vbus>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + status = "okay"; +}; + +/* SD1 */ +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sd_cd>; + cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&iomuxc { + /* + * Mux the Apalis GPIOs + * GPIO5, 6 used by optional fusion_F0710A kernel module + */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2 + &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4 + &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6 + &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8 + >; + + pinctrl_leds_ixora: ledsixoragrp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0 + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b0 + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0 + MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0 + >; + }; +}; -- 2.5.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html