From: Petr Štetiar <ynezz@xxxxxxx>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@xxxxxxxxxxx>
Signed-off-by: Petr Štetiar <ynezz@xxxxxxx>
Reviewed-by: Stefan Agner <stefan@xxxxxxxx>
---
Changes in v5:
- finally get rid of regulators simple bus as suggested by Lucas, Petr and Shawn
- use reg_xxx: regulator-xxx naming scheme as suggested by Shawn
- get rid of disabled hdmi node as suggested by Shawn
- have a new line between properties and sub-node as suggested by Shawn
- get rid of disabled usbh1 node as suggested by Shawn
- drop iomux/pinctrl function container nodes as suggested by Shawn
- added new lines between nodes as suggested by Shawn
- use consistent pinctrl group node naming schema xxxgrp as suggested by Shawn
- further clean-up and re-order iomux/pinctrl stuff
- configure eMMC reset as required once fast boot mode is used
- properly set usdhc1, usdhc2 and usdhc3 vqmmc-supply rather than vmmc-supply we previously set leading to wrong signal voltage being reported
Changes in v4:
- integrated review feedback from Fabio
Changes in v3:
- integrated review feedback from Petr
- integrated review feedback from Stefan
- move I2C DDC enablement and assignement handling into carrier board DTS where it belongs
- move CAN nodes up a little to keep the alphabetical order
- added an explanatory comment about PWR_I2C usage
Changes in v2:
- clarify exact Apalis iMX6Q/D SoM type in cover letter
- clarify exact Apalis iMX6Q/D module type and Ixora carrier board in model
node
- got rid of obsolete mmc aliases
- working SGTL5000 audio/sound integration
- working STMPE811 touch screen controller integration
- integrated review feedback from Lucas
- left and even added some more comments as I don't see why putting any
explanatory comments in dts' should be such a bad thing to do
- completely got rid of the memory node as that is something typically filled
in by the boot loader e.g. U-Boot
- without the regulators simple-bus it no longer boots
- even though we supposedly shipped a few hundred V1.0a modules drop DCE UART
support for now and simplify file layout
- replaced obsolete no-1-8-v by mainline supported voltage-ranges = <3300 3300>
usdhc property and yes card detects are indeed active low (;-p)
- integrated review feedback from Stefan
- fixed Ethernet PHY reset & interrupt (requires Micrel PHY driver to be
enabled)
- fixed HDMI DDC (requires GPIO-based bitbanging I2C to be enabled)
- fixed SPDIF
arch/arm/boot/dts/imx6qdl-apalis.dtsi | 984 ++++++++++++++++++++++++++++++++++
1 file changed, 984 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-apalis.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
new file mode 100644
index 0000000..b33e5a9
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
@@ -0,0 +1,984 @@
+/*
+ * Copyright 2014-2016 Toradex AG
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Toradex Apalis iMX6Q/D Module";
+ compatible = "toradex,apalis_imx6q", "fsl,imx6q";
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm4 0 5000000>;
+ status = "disabled";
+ };
+
+ /* DDC_I2C: I2C2_SDA/SCL on MXM3 205/207 */
+ i2cddc: i2c@0 {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_ddc>;
+ gpios = <&gpio3 16 GPIO_ACTIVE_HIGH /* sda */
+ &gpio2 30 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ status = "disabled";
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_2p5v: regulator-2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_regulator_usbotg_pwr>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ status = "disabled";
+ };
+
+ /* on module USB hub */
+ reg_usb_host_vbus_hub: regulator-usb-host-vbus-hub {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_regulator_usbhub_pwr>;
+ regulator-name = "usb_host_vbus_hub";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <2000>;
+ enable-active-high;
+ status = "okay";
+ };
+
+ reg_usb_host_vbus: regulator-usb-host-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
+ regulator-name = "usb_host_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_usb_host_vbus_hub>;
+ status = "disabled";
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-sgtl5000";
+ model = "imx6q-apalis-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "LINE_IN", "Line In Jack",
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <4>;
+ };
+
+ sound_spdif: sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ spdif-controller = <&spdif>;
+ spdif-in;
+ spdif-out;
+ status = "disabled";
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "disabled";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "disabled";
+};
+
+/* Apalis SPI1 */
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "disabled";
+};
+
+/* Apalis SPI2 */
+&ecspi2 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "disabled";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy>;
+ phy-reset-duration = <10>;
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@7 {
+ interrupt-parent = <&gpio1>;
+ interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
+ reg = <7>;
+ };
+ };
+};
+
+/*
+ * GEN1_I2C: I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier
+ * board)
+ */
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "disabled";
+};
+
+/*
+ * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
+ * touch screen controller
+ */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pmic: pfuze100@08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ codec: sgtl5000@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+
+ /* STMPE811 touch screen controller */
+ stmpe811@41 {
+ compatible = "st,stmpe811";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_touch_int>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x41>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-parent = <&gpio4>;
+ interrupt-controller;
+ id = <0>;
+ blocks = <0x5>;
+ irq-trigger = <0x1>;
+
+ stmpe_touchscreen {
+ compatible = "st,stmpe-ts";
+ reg = <0>;
+ /* 3.25 MHz ADC clock speed */
+ st,adc-freq = <1>;
+ /* 8 sample average control */
+ st,ave-ctrl = <3>;
+ /* 7 length fractional part in z */
+ st,fraction-z = <7>;
+ /*
+ * 50 mA typical 80 mA max touchscreen drivers
+ * current limit value
+ */
+ st,i-drive = <1>;
+ /* 12-bit ADC */
+ st,mod-12b = <1>;
+ /* internal ADC reference */
+ st,ref-sel = <0>;
+ /* ADC converstion time: 80 clocks */
+ st,sample-time = <4>;
+ /* 1 ms panel driver settling time */
+ st,settling = <3>;
+ /* 5 ms touch detect interrupt delay */
+ st,touch-det-delay = <5>;
+ };
+ };
+};
+
+/*
+ * GEN2_I2C, CAM: I2C3_SDA/SCL on MXM3 201/203 (unused)
+ */
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "recovery";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_recovery>;
+ scl-gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "disabled";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "disabled";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "disabled";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "disabled";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif>;
+ status = "disabled";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
+ fsl,dte-mode;
+ fsl,uart-has-rtscts;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2_dte>;
+ fsl,dte-mode;
+ fsl,uart-has-rtscts;
+ status = "disabled";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4_dte>;
+ fsl,dte-mode;
+ status = "disabled";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5_dte>;
+ fsl,dte-mode;
+ status = "disabled";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "disabled";
+};
+
+/* MMC1 */
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ vqmmc-supply = <®_3p3v>;
+ bus-width = <8>;
+ voltage-ranges = <3300 3300>;
+ status = "disabled";
+};
+
+/* SD1 */
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ vqmmc-supply = <®_3p3v>;
+ bus-width = <4>;
+ voltage-ranges = <3300 3300>;
+ status = "disabled";
+};
+
+/* eMMC */
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ vqmmc-supply = <®_3p3v>;
+ bus-width = <8>;
+ voltage-ranges = <3300 3300>;
+ non-removable;
+ status = "okay";
+};
+
+&weim {
+ status = "disabled";
+};
+
+&iomuxc {
+ /* pins used on module */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reset_moci>;
+
+ pinctrl_apalis_gpio1: gpio2io04grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x130b0
+ >;
+ };
+
+ pinctrl_apalis_gpio2: gpio2io05grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x130b0
+ >;
+ };
+
+ pinctrl_apalis_gpio3: gpio2io06grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x130b0
+ >;
+ };
+
+ pinctrl_apalis_gpio4: gpio2io07grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x130b0
+ >;
+ };
+
+ pinctrl_apalis_gpio5: gpio6io10grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x130b0
+ >;
+ };
+
+ pinctrl_apalis_gpio6: gpio6io09grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x130b0
+ >;
+ };
+
+ pinctrl_apalis_gpio7: gpio1io02grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x130b0
+ >;
+ };
+
+ pinctrl_apalis_gpio8: gpio1io06grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x130b0
+ >;
+ };
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x130b0
+ MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_cam_mclk: cammclkgrp {
+ fsl,pins = <
+ /* CAM sys_mclk */
+ MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x00b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT6__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_CSI0_DAT5__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_CSI0_DAT4__ECSPI1_SCLK 0x100b1
+ /* SPI1 cs */
+ MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ /* SPI2 cs */
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ /* Ethernet PHY reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x000b0
+ /* Ethernet PHY interrupt */
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x000b1
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
+ MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio1io04grp {
+ fsl,pins = <
+ /* Power button */
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_hdmi_cec: hdmicecgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c_ddc: gpioi2cddcgrp {
+ fsl,pins = <
+ /* DDC bitbang */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3_recovery: i2c3recoverygrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp { /* parallel camera */
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0xb0b1
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0xb0b1
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0xb0b1
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0xb0b1
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0xb0b1
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0xb0b1
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0xb0b1
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0xb0b1
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0xb0b1
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0xb0b1
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0xb0b1
+ >;
+ };
+
+ pinctrl_ipu1_lcdif: ipu1lcdifgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A16__IPU1_DI1_DISP_CLK 0x61
+ /* DE */
+ MX6QDL_PAD_EIM_DA10__IPU1_DI1_PIN15 0x61
+ /* HSync */
+ MX6QDL_PAD_EIM_DA11__IPU1_DI1_PIN02 0x61
+ /* VSync */
+ MX6QDL_PAD_EIM_DA12__IPU1_DI1_PIN03 0x61
+ MX6QDL_PAD_EIM_DA9__IPU1_DISP1_DATA00 0x61
+ MX6QDL_PAD_EIM_DA8__IPU1_DISP1_DATA01 0x61
+ MX6QDL_PAD_EIM_DA7__IPU1_DISP1_DATA02 0x61
+ MX6QDL_PAD_EIM_DA6__IPU1_DISP1_DATA03 0x61
+ MX6QDL_PAD_EIM_DA5__IPU1_DISP1_DATA04 0x61
+ MX6QDL_PAD_EIM_DA4__IPU1_DISP1_DATA05 0x61
+ MX6QDL_PAD_EIM_DA3__IPU1_DISP1_DATA06 0x61
+ MX6QDL_PAD_EIM_DA2__IPU1_DISP1_DATA07 0x61
+ MX6QDL_PAD_EIM_DA1__IPU1_DISP1_DATA08 0x61
+ MX6QDL_PAD_EIM_DA0__IPU1_DISP1_DATA09 0x61
+ MX6QDL_PAD_EIM_EB1__IPU1_DISP1_DATA10 0x61
+ MX6QDL_PAD_EIM_EB0__IPU1_DISP1_DATA11 0x61
+ MX6QDL_PAD_EIM_A17__IPU1_DISP1_DATA12 0x61
+ MX6QDL_PAD_EIM_A18__IPU1_DISP1_DATA13 0x61
+ MX6QDL_PAD_EIM_A19__IPU1_DISP1_DATA14 0x61
+ MX6QDL_PAD_EIM_A20__IPU1_DISP1_DATA15 0x61
+ MX6QDL_PAD_EIM_A21__IPU1_DISP1_DATA16 0x61
+ MX6QDL_PAD_EIM_A22__IPU1_DISP1_DATA17 0x61
+ MX6QDL_PAD_EIM_A23__IPU1_DISP1_DATA18 0x61
+ MX6QDL_PAD_EIM_A24__IPU1_DISP1_DATA19 0x61
+ MX6QDL_PAD_EIM_D31__IPU1_DISP1_DATA20 0x61
+ MX6QDL_PAD_EIM_D30__IPU1_DISP1_DATA21 0x61
+ MX6QDL_PAD_EIM_D26__IPU1_DISP1_DATA22 0x61
+ MX6QDL_PAD_EIM_D27__IPU1_DISP1_DATA23 0x61
+ >;
+ };
+
+ pinctrl_ipu2_vdac: ipu2vdacgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK 0xd1
+ MX6QDL_PAD_DI0_PIN15__IPU2_DI0_PIN15 0xd1
+ MX6QDL_PAD_DI0_PIN2__IPU2_DI0_PIN02 0xd1
+ MX6QDL_PAD_DI0_PIN3__IPU2_DI0_PIN03 0xd1
+ MX6QDL_PAD_DISP0_DAT0__IPU2_DISP0_DATA00 0xf9
+ MX6QDL_PAD_DISP0_DAT1__IPU2_DISP0_DATA01 0xf9
+ MX6QDL_PAD_DISP0_DAT2__IPU2_DISP0_DATA02 0xf9
+ MX6QDL_PAD_DISP0_DAT3__IPU2_DISP0_DATA03 0xf9
+ MX6QDL_PAD_DISP0_DAT4__IPU2_DISP0_DATA04 0xf9
+ MX6QDL_PAD_DISP0_DAT5__IPU2_DISP0_DATA05 0xf9
+ MX6QDL_PAD_DISP0_DAT6__IPU2_DISP0_DATA06 0xf9
+ MX6QDL_PAD_DISP0_DAT7__IPU2_DISP0_DATA07 0xf9
+ MX6QDL_PAD_DISP0_DAT8__IPU2_DISP0_DATA08 0xf9
+ MX6QDL_PAD_DISP0_DAT9__IPU2_DISP0_DATA09 0xf9
+ MX6QDL_PAD_DISP0_DAT10__IPU2_DISP0_DATA10 0xf9
+ MX6QDL_PAD_DISP0_DAT11__IPU2_DISP0_DATA11 0xf9
+ MX6QDL_PAD_DISP0_DAT12__IPU2_DISP0_DATA12 0xf9
+ MX6QDL_PAD_DISP0_DAT13__IPU2_DISP0_DATA13 0xf9
+ MX6QDL_PAD_DISP0_DAT14__IPU2_DISP0_DATA14 0xf9
+ MX6QDL_PAD_DISP0_DAT15__IPU2_DISP0_DATA15 0xf9
+ >;
+ };
+
+ pinctrl_mmc_cd: gpiommccdgrp {
+ fsl,pins = <
+ /* MMC1 CD */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x000b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
+ fsl,pins = <
+ /* USBH_EN */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x0f058
+ >;
+ };
+
+ pinctrl_regulator_usbhub_pwr: gpioregusbhubpwrgrp {
+ fsl,pins = <
+ /* USBH_HUB_EN */
+ MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0f058
+ >;
+ };
+
+ pinctrl_regulator_usbotg_pwr: gpioregusbotgpwrgrp {
+ fsl,pins = <
+ /* USBO1 power en */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0f058
+ >;
+ };
+
+ pinctrl_reset_moci: gpioresetmocigrp {
+ fsl,pins = <
+ /* RESET_MOCI control */
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x0f058
+ >;
+ };
+
+ pinctrl_sd_cd: gpiosdcdgrp {
+ fsl,pins = <
+ /* SD1 CD */
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x000b0
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
+ MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_touch_int: gpiotouchintgrp {
+ fsl,pins = <
+ /* STMPE811 interrupt */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart1_dce: uart1dcegrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ /* DTE mode */
+ pinctrl_uart1_dte: uart1dtegrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D19__UART1_RTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D20__UART1_CTS_B 0x1b0b1
+ >;
+ };
+
+ /* Additional DTR, DSR, DCD */
+ pinctrl_uart1_ctrl: uart1ctrlgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
+ MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
+ MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart2_dce: uart2dcegrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ >;
+ };
+
+ /* DTE mode */
+ pinctrl_uart2_dte: uart2dtegrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT6__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT5__UART2_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4_dce: uart4dcegrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ /* DTE mode */
+ pinctrl_uart4_dte: uart4dtegrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5_dce: uart5dcegrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ /* DTE mode */
+ pinctrl_uart5_dte: uart5dtegrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_RX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
+ MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x17071
+ MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x17071
+ MX6QDL_PAD_NANDF_D2__SD1_DATA6 0x17071
+ MX6QDL_PAD_NANDF_D3__SD1_DATA7 0x17071
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17071
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10071
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17071
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17071
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17071
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17071
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ /* eMMC reset */
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3100mhzgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170b9
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170b9
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170b9
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170b9
+ /* eMMC reset */
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3200mhzgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170f9
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170f9
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170f9
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170f9
+ /* eMMC reset */
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x170f9
+ >;
+ };
+};
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
