Nicolas Ferre <nicolas.ferre@xxxxxxxxx> writes:
> Le 27/01/2016 16:53, Måns Rullgård a écrit :
>> Nicolas Ferre <nicolas.ferre@xxxxxxxxx> writes:
>>
>>> Le 05/01/2016 22:50, Måns Rullgård a écrit :
>>>> Cyrille Pitchen <cyrille.pitchen@xxxxxxxxx> writes:
>>>>
>>>>> This patch relies on the CSAAT (Chip Select Active After Transfer) feature
>>>>> introduced by the version 2 of the spi controller. This new mode allows to
>>>>> use properly the internal chip-select output pin of the spi controller
>>>>> instead of using external gpios. Consequently, the "cs-gpios" device-tree
>>>>> property becomes optional.
>>>>>
>>>>> When the new CSAAT bit is set into the Chip Select Register, the internal
>>>>> chip-select output pin remains asserted till both the following conditions
>>>>> become true:
>>>>> - the LASTXFER bit is set into the Control Register (or the Transmit Data
>>>>> Register)
>>>>> - the Transmit Data Register and its shift register are empty.
>>>>>
>>>>> WARNING: if the LASTXFER bit is set into the Control Register then new
>>>>> data are written into the Transmit Data Register fast enough to keep its
>>>>> shifter not empty, the chip-select output pin remains asserted. Only when
>>>>> the shifter becomes empty, the chip-select output pin is unasserted.
>>>>>
>>>>> When the CSAAT bit is clear in the Chip Select Register, the LASTXFER bit
>>>>> is ignored in both the Control Register and the Transmit Data Register.
>>>>> The internal chip-select output pin remains active as long as the Transmit
>>>>> Data Register or its shift register are not empty.
>>>>>
>>>>> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@xxxxxxxxx>
>>>>> ---
>>>>> drivers/spi/spi-atmel.c | 37 ++++++++++++++++++++++++++++---------
>>>>> 1 file changed, 28 insertions(+), 9 deletions(-)
>>>>
>>>> [...]
>>>>
>>>>> @@ -1338,6 +1350,13 @@ static int atmel_spi_probe(struct platform_device *pdev)
>>>>>
>>>>> atmel_get_caps(as);
>>>>>
>>>>> + as->use_cs_gpios = true;
>>>>> + if (atmel_spi_is_v2(as) &&
>>>>> + !of_get_property(pdev->dev.of_node, "cs-gpios", NULL)) {
>>>>> + as->use_cs_gpios = false;
>>>>> + master->num_chipselect = 4;
>>>>> + }
>>>>
>>>> This part breaks the AVR32 boards and probably anything else that
>>>> doesn't use devicetree but does use GPIOs for chip select.
>>>
>>> Hi Mans,
>>>
>>> I have difficulties finding why you may enter this test. So, maybe you
>>> can give me a clue by reading for me the value that resides in the SPI
>>> version register: you can have it by reading at 0xFFE000FC for instance
>>> (actually the atmel_get_caps() dev_info() call gives it as well in the
>>> boot log which is somewhat easier: I tried to find one on the Internet
>>> without success...).
>>>
>>> So I think that just fixing the logic in atmel_get_caps() introduced by
>>> d4820b7496219edd9a7055022681364d304525f7 can make it come back to a
>>> situation where the ARV32 was more tested than nowadays.
>>
>> atmel_spi atmel_spi.0: version: 0x171
>> atmel_spi atmel_spi.0: Atmel SPI Controller at 0xffe00000 (irq 3)
>>
>> atmel_spi_is_v2() returns true for version > 0x121.
>
> Ok, thanks: we thought that AVR32 didn't have a v2 IP: obviously it has.
> So yes, I extract the patch by Cyrille to correct this and send it right
> now.
>
> If you can test it, it's even better ;-)
I saw the patch, will test it later.
--
Måns Rullgård
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
