On 11/25/2015 12:39 AM, Dmitry Lifshitz wrote:
[...]
> diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
> new file mode 100644
> index 0000000..b11d7da
> --- /dev/null
> +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
[...]
> +/ {
> + model = "CompuLab CL-SOM-AM57x";
> + compatible = "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>; /* 512 MB - minimal configuration */
I think if you like to enable LPAE, the format might look a little
different..
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&leds_pins_default>;
> +
> + led@0 {
> + label = "cl-som-am57x:green";
> + gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + default-state = "off";
> + };
> + };
> +};
> +
> +&dra7_pmx_core {
> + leds_pins_default: leds_pins_default {
> + pinctrl-single,pins = <
> + DRA7XX_CORE_IOPAD(0x347c, PIN_OUTPUT | MUX_MODE14) /* gpmc_a15.gpio2_5 */
> + >;
> + };
> +
> + i2c1_pins_default: i2c1_pins_default {
> + pinctrl-single,pins = <
> + DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */
> + DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */
> + >;
> + };
> +
> + tps659038_pins_default: tps659038_pins_default {
> + pinctrl-single,pins = <
> + DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
> + >;
> + };
Generic comment: As per requirements of the SoC -> all pinctrl must be
done in bootloader. this was a recommendation that came in too late
for TI platforms that got introduced in upstream, but that cleanup
should eventually take place as well.
> +};
> +
> +&i2c1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins_default>;
> + clock-frequency = <400000>;
> +
> + tps659038: tps659038@58 {
> + compatible = "ti,tps659038";
> + reg = <0x58>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
Also See: https://patchwork.kernel.org/patch/7596541/ ->
Documentation/devicetree/bindings/i2c/i2c.txt -> since you seem to
have a PMIC with power button, you might be able to get wakeup source
also there.
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&tps659038_pins_default>;
> +
> + #interrupt-cells = <2>;
> + interrupt-controller;
> +
> + ti,system-power-controller;
Assuming powerhold signal and BOOT0,1 is proper here, else poweroff
will never work.
> +
> + tps659038_pmic {
> + compatible = "ti,tps659038-pmic";
> +
> + regulators {
> + smps12_reg: smps12 {
> + /* VDD_MPU */
> + regulator-name = "smps12";
> + regulator-min-microvolt = < 850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + smps3_reg: smps3 {
> + /* VDD_DDR */
> + regulator-name = "smps3";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + smps45_reg: smps45 {
> + /* VDD_DSPEVE */
> + regulator-name = "smps45";
> + regulator-min-microvolt = < 850000>;
> + regulator-max-microvolt = <1160000>;
1.25v if you want to support OPP_HIGH. as per latest data sheet.
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + smps6_reg: smps6 {
> + /* VDD_GPU */
> + regulator-name = "smps6";
> + regulator-min-microvolt = < 850000>;
> + regulator-max-microvolt = <1160000>;
1.25v if you want to support OPP_HIGH. as per latest data sheet.
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + smps7_reg: smps7 {
> + /* VDD_CORE */
> + regulator-name = "smps7";
> + regulator-min-microvolt = < 850000>;
> + regulator-max-microvolt = <1160000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + smps8_reg: smps8 {
> + /* VDD_IVA */
> + regulator-name = "smps8";
> + regulator-min-microvolt = < 850000>;
> + regulator-max-microvolt = <1160000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + smps9_reg: smps9 {
> + /* PMIC_3V3 */
> + regulator-name = "smps9";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> +
> + ldo1_reg: ldo1 {
> + /* VDD_SD / VDDSHV8 */
> + regulator-name = "ldo1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
for eventual UHS mode support, it is recommended to keep VDD_SD
separate from VDDSHV8. many of TI evms also suffer from this issue :(
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: ldo2 {
> + /* VDD_1V8 */
> + regulator-name = "ldo2";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + ldo3_reg: ldo3 {
> + /* VDDA_1V8_PHYA */
> + regulator-name = "ldo3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + ldo4_reg: ldo4 {
> + /* VDDA_1V8_PHYB */
> + regulator-name = "ldo4";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
Happy to see this is already split up. you might want to document
which PHYs are supplied by PHYA/B in comments for future reference
instead of having to dig through schematics to figure that out..
> +
> + ldo9_reg: ldo9 {
> + /* VDD_RTC */
> + regulator-name = "ldo9";
> + regulator-min-microvolt = <1050000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-always-on;
> + regulator-boot-on;
as per data sheet:
"VD_RTC can optionally be tied to VD_CORE and operate at the VD_CORE
AVS voltages."
I assume that is not the case here.
> + };
> +
> + ldoln_reg: ldoln {
> + /* VDDA_1V8_PLL */
> + regulator-name = "ldoln";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + ldousb_reg: ldousb {
> + /* VDDA_3V_USB: VDDA_USBHS33 */
> + regulator-name = "ldousb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
All SoC VDDAs must be always-on.
[...]
--
Regards,
Nishanth Menon
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
