On Mon, Nov 16, 2015 at 07:12:36PM +0000, Simon Arlott wrote:
> Add device tree binding for the BCM6345 interrupt controller.
>
> This controller is similar to the SMP-capable BCM7038 and
> the BCM3380 but with packed interrupt registers.
>
> Signed-off-by: Simon Arlott <simon@xxxxxxxxxxx>
> ---
> On 16/11/15 15:34, Rob Herring wrote:
> > On Sun, Nov 15, 2015 at 04:51:16PM +0000, Simon Arlott wrote:
> >> Add device tree binding for the BCM63168 interrupt controller.
> >>
> >> This controller is similar to the SMP-capable BCM7038 and
> >> the BCM3380 but with packed interrupt registers.
> >>
> >> Signed-off-by: Simon Arlott <simon@xxxxxxxxxxx>
> >
> > Acked-by: Rob Herring <robh@xxxxxxxxxx>
>
> I'm going to rename this to bcm6345-l1 as suggested by Jonas Gorski, and
> the binding now specifies a <soc> version of the compatible name to be
> included.
Acked-by: Rob Herring <robh@xxxxxxxxxx>
> .../interrupt-controller/brcm,bcm6345-l1-intc.txt | 57 ++++++++++++++++++++++
> 1 file changed, 57 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt
>
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt
> new file mode 100644
> index 0000000..c5bdcf1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l1-intc.txt
> @@ -0,0 +1,57 @@
> +Broadcom BCM6345-style Level 1 interrupt controller
> +
> +This block is a first level interrupt controller that is typically connected
> +directly to one of the HW INT lines on each CPU.
> +
> +Key elements of the hardware design include:
> +
> +- 32, 64 or 128 incoming level IRQ lines
> +
> +- Most onchip peripherals are wired directly to an L1 input
> +
> +- A separate instance of the register set for each CPU, allowing individual
> + peripheral IRQs to be routed to any CPU
> +
> +- Contains one or more enable/status word pairs per CPU
> +
> +- No atomic set/clear operations
> +
> +- No polarity/level/edge settings
> +
> +- No FIFO or priority encoder logic; software is expected to read all
> + 2-4 status words to determine which IRQs are pending
> +
> +Required properties:
> +
> +- compatible: should be "brcm,bcm<soc>-l1-intc", "brcm,bcm6345-l1-intc"
> +- reg: specifies the base physical address and size of the registers;
> + the number of supported IRQs is inferred from the size argument
> +- interrupt-controller: identifies the node as an interrupt controller
> +- #interrupt-cells: specifies the number of cells needed to encode an interrupt
> + source, should be 1.
> +- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
> + this one is cascaded from
> +- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
> + node; valid values depend on the type of parent interrupt controller
> +
> +If multiple reg ranges and interrupt-parent entries are present on an SMP
> +system, the driver will allow IRQ SMP affinity to be set up through the
> +/proc/irq/ interface. In the simplest possible configuration, only one
> +reg range and one interrupt-parent is needed.
> +
> +The driver operates in native CPU endian by default, there is no support for
> +specifying an alternative endianness.
> +
> +Example:
> +
> +periph_intc: periph_intc@10000000 {
> + compatible = "brcm,bcm63168-l1-intc", "brcm,bcm6345-l1-intc";
> + reg = <0x10000020 0x20>,
> + <0x10000040 0x20>;
> +
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + interrupt-parent = <&cpu_intc>;
> + interrupts = <2>, <3>;
> +};
> --
> 2.1.4
>
> --
> Simon Arlott
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
