Convert mx23/mx28 dts filed to use the pinctrl header files. NOTE: During automatic conversion of these files to use the pinconfig definitions an inconsistency has been found in: arch/arm/boot/dts/imx28-apx4devkit.dts According to the comment the function for pad SSP2_SS0 should have been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131 represents: MX28_PAD_SSP2_SS0__AUART3_TX I used the later (though probably wrong) definition because that's what is actually being used in the DTB. Signed-off-by: Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx> --- arch/arm/boot/dts/imx23-evk.dts | 10 +- arch/arm/boot/dts/imx23-olinuxino.dts | 6 +- arch/arm/boot/dts/imx23-stmp378x_devb.dts | 6 +- arch/arm/boot/dts/imx23.dtsi | 163 +++++++------- arch/arm/boot/dts/imx28-apf28.dts | 2 +- arch/arm/boot/dts/imx28-apf28dev.dts | 24 +- arch/arm/boot/dts/imx28-apx4devkit.dts | 38 ++-- arch/arm/boot/dts/imx28-cfa10036.dts | 8 +- arch/arm/boot/dts/imx28-cfa10037.dts | 6 +- arch/arm/boot/dts/imx28-cfa10049.dts | 84 ++++---- arch/arm/boot/dts/imx28-cfa10055.dts | 56 +++--- arch/arm/boot/dts/imx28-cfa10056.dts | 20 +- arch/arm/boot/dts/imx28-cfa10057.dts | 48 ++-- arch/arm/boot/dts/imx28-cfa10058.dts | 12 +- arch/arm/boot/dts/imx28-evk.dts | 32 ++-- arch/arm/boot/dts/imx28-m28evk.dts | 16 +- arch/arm/boot/dts/imx28-sps1.dts | 8 +- arch/arm/boot/dts/imx28.dtsi | 337 +++++++++++++++-------------- 18 files changed, 439 insertions(+), 437 deletions(-) diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts index 185c7c0..fdd8b27 100644 --- a/arch/arm/boot/dts/imx23-evk.dts +++ b/arch/arm/boot/dts/imx23-evk.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx23.dtsi" +#include "imx23.dtsi" / { model = "Freescale i.MX23 Evaluation Kit"; @@ -45,10 +45,10 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x1123 /* MX23_PAD_LCD_RESET__GPIO_1_18 */ - 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */ - 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */ - 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ + MX23_PAD_LCD_RESET__GPIO_1_18 + MX23_PAD_PWM3__GPIO_1_29 + MX23_PAD_PWM4__GPIO_1_30 + MX23_PAD_SSP1_DETECT__SSP1_DETECT >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts index fc766ae..f575434 100644 --- a/arch/arm/boot/dts/imx23-olinuxino.dts +++ b/arch/arm/boot/dts/imx23-olinuxino.dts @@ -12,7 +12,7 @@ */ /dts-v1/; -/include/ "imx23.dtsi" +#include "imx23.dtsi" / { model = "i.MX23 Olinuxino Low Cost Board"; @@ -40,7 +40,7 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x0113 /* MX23_PAD_GPMI_ALE__GPIO_0_17 */ + MX23_PAD_GPMI_ALE__GPIO_0_17 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -50,7 +50,7 @@ led_pin_gpio2_1: led_gpio2_1@0 { reg = <0>; fsl,pinmux-ids = < - 0x2013 /* MX23_PAD_SSP1_DETECT__GPIO_2_1 */ + MX23_PAD_SSP1_DETECT__GPIO_2_1 >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/imx23-stmp378x_devb.dts index 85c3864..2c8a9b0 100644 --- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts +++ b/arch/arm/boot/dts/imx23-stmp378x_devb.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx23.dtsi" +#include "imx23.dtsi" / { model = "Freescale STMP378x Development Board"; @@ -39,8 +39,8 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */ - 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */ + MX23_PAD_PWM3__GPIO_1_29 + MX23_PAD_PWM4__GPIO_1_30 >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi index 28b5ce2..ff96e59 100644 --- a/arch/arm/boot/dts/imx23.dtsi +++ b/arch/arm/boot/dts/imx23.dtsi @@ -9,7 +9,8 @@ * http://www.gnu.org/copyleft/gpl.html */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" +#include "imx23-pinfunc.h" / { interrupt-parent = <&icoll>; @@ -137,8 +138,8 @@ duart_pins_a: duart@0 { reg = <0>; fsl,pinmux-ids = < - 0x11a2 /* MX23_PAD_PWM0__DUART_RX */ - 0x11b2 /* MX23_PAD_PWM1__DUART_TX */ + MX23_PAD_PWM0__DUART_RX + MX23_PAD_PWM1__DUART_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -148,10 +149,10 @@ auart0_pins_a: auart0@0 { reg = <0>; fsl,pinmux-ids = < - 0x01c0 /* MX23_PAD_AUART1_RX__AUART1_RX */ - 0x01d0 /* MX23_PAD_AUART1_TX__AUART1_TX */ - 0x01a0 /* MX23_PAD_AUART1_CTS__AUART1_CTS */ - 0x01b0 /* MX23_PAD_AUART1_RTS__AUART1_RTS */ + MX23_PAD_AUART1_RX__AUART1_RX + MX23_PAD_AUART1_TX__AUART1_TX + MX23_PAD_AUART1_CTS__AUART1_CTS + MX23_PAD_AUART1_RTS__AUART1_RTS >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -161,8 +162,8 @@ auart0_2pins_a: auart0-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x01e2 /* MX23_PAD_I2C_SCL__AUART1_TX */ - 0x01f2 /* MX23_PAD_I2C_SDA__AUART1_RX */ + MX23_PAD_I2C_SCL__AUART1_TX + MX23_PAD_I2C_SDA__AUART1_RX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -172,23 +173,23 @@ gpmi_pins_a: gpmi-nand@0 { reg = <0>; fsl,pinmux-ids = < - 0x0000 /* MX23_PAD_GPMI_D00__GPMI_D00 */ - 0x0010 /* MX23_PAD_GPMI_D01__GPMI_D01 */ - 0x0020 /* MX23_PAD_GPMI_D02__GPMI_D02 */ - 0x0030 /* MX23_PAD_GPMI_D03__GPMI_D03 */ - 0x0040 /* MX23_PAD_GPMI_D04__GPMI_D04 */ - 0x0050 /* MX23_PAD_GPMI_D05__GPMI_D05 */ - 0x0060 /* MX23_PAD_GPMI_D06__GPMI_D06 */ - 0x0070 /* MX23_PAD_GPMI_D07__GPMI_D07 */ - 0x0100 /* MX23_PAD_GPMI_CLE__GPMI_CLE */ - 0x0110 /* MX23_PAD_GPMI_ALE__GPMI_ALE */ - 0x0130 /* MX23_PAD_GPMI_RDY0__GPMI_RDY0 */ - 0x0140 /* MX23_PAD_GPMI_RDY1__GPMI_RDY1 */ - 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */ - 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */ - 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */ - 0x21b0 /* MX23_PAD_GPMI_CE1N__GPMI_CE1N */ - 0x21c0 /* MX23_PAD_GPMI_CE0N__GPMI_CE0N */ + MX23_PAD_GPMI_D00__GPMI_D00 + MX23_PAD_GPMI_D01__GPMI_D01 + MX23_PAD_GPMI_D02__GPMI_D02 + MX23_PAD_GPMI_D03__GPMI_D03 + MX23_PAD_GPMI_D04__GPMI_D04 + MX23_PAD_GPMI_D05__GPMI_D05 + MX23_PAD_GPMI_D06__GPMI_D06 + MX23_PAD_GPMI_D07__GPMI_D07 + MX23_PAD_GPMI_CLE__GPMI_CLE + MX23_PAD_GPMI_ALE__GPMI_ALE + MX23_PAD_GPMI_RDY0__GPMI_RDY0 + MX23_PAD_GPMI_RDY1__GPMI_RDY1 + MX23_PAD_GPMI_WPN__GPMI_WPN + MX23_PAD_GPMI_WRN__GPMI_WRN + MX23_PAD_GPMI_RDN__GPMI_RDN + MX23_PAD_GPMI_CE1N__GPMI_CE1N + MX23_PAD_GPMI_CE0N__GPMI_CE0N >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -197,9 +198,9 @@ gpmi_pins_fixup: gpmi-pins-fixup { fsl,pinmux-ids = < - 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */ - 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */ - 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */ + MX23_PAD_GPMI_WPN__GPMI_WPN + MX23_PAD_GPMI_WRN__GPMI_WRN + MX23_PAD_GPMI_RDN__GPMI_RDN >; fsl,drive-strength = <2>; }; @@ -207,12 +208,12 @@ mmc0_4bit_pins_a: mmc0-4bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */ - 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */ - 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */ - 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */ - 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */ - 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + MX23_PAD_SSP1_DATA0__SSP1_DATA0 + MX23_PAD_SSP1_DATA1__SSP1_DATA1 + MX23_PAD_SSP1_DATA2__SSP1_DATA2 + MX23_PAD_SSP1_DATA3__SSP1_DATA3 + MX23_PAD_SSP1_CMD__SSP1_CMD + MX23_PAD_SSP1_SCK__SSP1_SCK >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -222,17 +223,17 @@ mmc0_8bit_pins_a: mmc0-8bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */ - 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */ - 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */ - 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */ - 0x0082 /* MX23_PAD_GPMI_D08__SSP1_DATA4 */ - 0x0092 /* MX23_PAD_GPMI_D09__SSP1_DATA5 */ - 0x00a2 /* MX23_PAD_GPMI_D10__SSP1_DATA6 */ - 0x00b2 /* MX23_PAD_GPMI_D11__SSP1_DATA7 */ - 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */ - 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ - 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + MX23_PAD_SSP1_DATA0__SSP1_DATA0 + MX23_PAD_SSP1_DATA1__SSP1_DATA1 + MX23_PAD_SSP1_DATA2__SSP1_DATA2 + MX23_PAD_SSP1_DATA3__SSP1_DATA3 + MX23_PAD_GPMI_D08__SSP1_DATA4 + MX23_PAD_GPMI_D09__SSP1_DATA5 + MX23_PAD_GPMI_D10__SSP1_DATA6 + MX23_PAD_GPMI_D11__SSP1_DATA7 + MX23_PAD_SSP1_CMD__SSP1_CMD + MX23_PAD_SSP1_DETECT__SSP1_DETECT + MX23_PAD_SSP1_SCK__SSP1_SCK >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -241,8 +242,8 @@ mmc0_pins_fixup: mmc0-pins-fixup { fsl,pinmux-ids = < - 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ - 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + MX23_PAD_SSP1_DETECT__SSP1_DETECT + MX23_PAD_SSP1_SCK__SSP1_SCK >; fsl,pull-up = <0>; }; @@ -250,7 +251,7 @@ pwm2_pins_a: pwm2@0 { reg = <0>; fsl,pinmux-ids = < - 0x11c0 /* MX23_PAD_PWM2__PWM2 */ + MX23_PAD_PWM2__PWM2 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -260,34 +261,34 @@ lcdif_24bit_pins_a: lcdif-24bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX23_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX23_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX23_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX23_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX23_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX23_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX23_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX23_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX23_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX23_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX23_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX23_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX23_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX23_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX23_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX23_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX23_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX23_PAD_LCD_D17__LCD_D17 */ - 0x0081 /* MX23_PAD_GPMI_D08__LCD_D18 */ - 0x0091 /* MX23_PAD_GPMI_D09__LCD_D19 */ - 0x00a1 /* MX23_PAD_GPMI_D10__LCD_D20 */ - 0x00b1 /* MX23_PAD_GPMI_D11__LCD_D21 */ - 0x00c1 /* MX23_PAD_GPMI_D12__LCD_D22 */ - 0x00d1 /* MX23_PAD_GPMI_D13__LCD_D23 */ - 0x1160 /* MX23_PAD_LCD_DOTCK__LCD_DOTCK */ - 0x1170 /* MX23_PAD_LCD_ENABLE__LCD_ENABLE */ - 0x1180 /* MX23_PAD_LCD_HSYNC__LCD_HSYNC */ - 0x1190 /* MX23_PAD_LCD_VSYNC__LCD_VSYNC */ + MX23_PAD_LCD_D00__LCD_D00 + MX23_PAD_LCD_D01__LCD_D01 + MX23_PAD_LCD_D02__LCD_D02 + MX23_PAD_LCD_D03__LCD_D03 + MX23_PAD_LCD_D04__LCD_D04 + MX23_PAD_LCD_D05__LCD_D05 + MX23_PAD_LCD_D06__LCD_D06 + MX23_PAD_LCD_D07__LCD_D07 + MX23_PAD_LCD_D08__LCD_D08 + MX23_PAD_LCD_D09__LCD_D09 + MX23_PAD_LCD_D10__LCD_D10 + MX23_PAD_LCD_D11__LCD_D11 + MX23_PAD_LCD_D12__LCD_D12 + MX23_PAD_LCD_D13__LCD_D13 + MX23_PAD_LCD_D14__LCD_D14 + MX23_PAD_LCD_D15__LCD_D15 + MX23_PAD_LCD_D16__LCD_D16 + MX23_PAD_LCD_D17__LCD_D17 + MX23_PAD_GPMI_D08__LCD_D18 + MX23_PAD_GPMI_D09__LCD_D19 + MX23_PAD_GPMI_D10__LCD_D20 + MX23_PAD_GPMI_D11__LCD_D21 + MX23_PAD_GPMI_D12__LCD_D22 + MX23_PAD_GPMI_D13__LCD_D23 + MX23_PAD_LCD_DOTCK__LCD_DOTCK + MX23_PAD_LCD_ENABLE__LCD_ENABLE + MX23_PAD_LCD_HSYNC__LCD_HSYNC + MX23_PAD_LCD_VSYNC__LCD_VSYNC >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -297,10 +298,10 @@ spi2_pins_a: spi2@0 { reg = <0>; fsl,pinmux-ids = < - 0x0182 /* MX23_PAD_GPMI_WRN__SSP2_SCK */ - 0x0142 /* MX23_PAD_GPMI_RDY1__SSP2_CMD */ - 0x0002 /* MX23_PAD_GPMI_D00__SSP2_DATA0 */ - 0x0032 /* MX23_PAD_GPMI_D03__SSP2_DATA3 */ + MX23_PAD_GPMI_WRN__SSP2_SCK + MX23_PAD_GPMI_RDY1__SSP2_CMD + MX23_PAD_GPMI_D00__SSP2_DATA0 + MX23_PAD_GPMI_D03__SSP2_DATA3 >; fsl,drive-strength = <1>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts index 7eb0758..7198fe3 100644 --- a/arch/arm/boot/dts/imx28-apf28.dts +++ b/arch/arm/boot/dts/imx28-apf28.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "Armadeus Systems APF28 module"; diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts index b602494..7d923cc 100644 --- a/arch/arm/boot/dts/imx28-apf28dev.dts +++ b/arch/arm/boot/dts/imx28-apf28dev.dts @@ -10,7 +10,7 @@ */ /* APF28Dev is a docking board for the APF28 SOM */ -/include/ "imx28-apf28.dts" +#include "imx28-apf28.dts" / { model = "Armadeus Systems APF28Dev docking/development board"; @@ -41,13 +41,13 @@ hog_pins_apf28dev: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x1103 /* MX28_PAD_LCD_D16__GPIO_1_16 */ - 0x1113 /* MX28_PAD_LCD_D17__GPIO_1_17 */ - 0x1123 /* MX28_PAD_LCD_D18__GPIO_1_18 */ - 0x1133 /* MX28_PAD_LCD_D19__GPIO_1_19 */ - 0x1143 /* MX28_PAD_LCD_D20__GPIO_1_20 */ - 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */ - 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */ + MX28_PAD_LCD_D16__GPIO_1_16 + MX28_PAD_LCD_D17__GPIO_1_17 + MX28_PAD_LCD_D18__GPIO_1_18 + MX28_PAD_LCD_D19__GPIO_1_19 + MX28_PAD_LCD_D20__GPIO_1_20 + MX28_PAD_LCD_D21__GPIO_1_21 + MX28_PAD_LCD_D22__GPIO_1_22 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -57,10 +57,10 @@ lcdif_pins_apf28dev: lcdif-apf28dev@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts index 0e7fed4..cb19dc1 100644 --- a/arch/arm/boot/dts/imx28-apx4devkit.dts +++ b/arch/arm/boot/dts/imx28-apx4devkit.dts @@ -1,5 +1,5 @@ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "Bluegiga APX4 Development Kit"; @@ -40,13 +40,13 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */ - 0x0153 /* MX28_PAD_GPMI_RDY1__GPIO_0_21 */ - 0x2123 /* MX28_PAD_SSP2_MISO__GPIO_2_18 */ - 0x2131 /* MX28_PAD_SSP2_SS0__GPIO_2_19 */ - 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */ - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ - 0x4143 /* MX28_PAD_JTAG_RTCK__GPIO_4_20 */ + MX28_PAD_GPMI_CE1N__GPIO_0_17 + MX28_PAD_GPMI_RDY1__GPIO_0_21 + MX28_PAD_SSP2_MISO__GPIO_2_18 + MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */ + MX28_PAD_PWM3__GPIO_3_28 + MX28_PAD_LCD_RESET__GPIO_3_30 + MX28_PAD_JTAG_RTCK__GPIO_4_20 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -56,10 +56,10 @@ lcdif_pins_apx4: lcdif-apx4@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -69,12 +69,12 @@ mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 { reg = <0>; fsl,pinmux-ids = < - 0x2041 /* MX28_PAD_SSP0_DATA4__SSP2_D0 */ - 0x2051 /* MX28_PAD_SSP0_DATA5__SSP2_D3 */ - 0x2061 /* MX28_PAD_SSP0_DATA6__SSP2_CMD */ - 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */ - 0x2141 /* MX28_PAD_SSP2_SS1__SSP2_D1 */ - 0x2151 /* MX28_PAD_SSP2_SS2__SSP2_D2 */ + MX28_PAD_SSP0_DATA4__SSP2_D0 + MX28_PAD_SSP0_DATA5__SSP2_D3 + MX28_PAD_SSP0_DATA6__SSP2_CMD + MX28_PAD_SSP0_DATA7__SSP2_SCK + MX28_PAD_SSP2_SS1__SSP2_D1 + MX28_PAD_SSP2_SS2__SSP2_D2 >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -83,7 +83,7 @@ mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 { fsl,pinmux-ids = < - 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */ + MX28_PAD_SSP0_DATA7__SSP2_SCK >; fsl,drive-strength = <2>; fsl,pull-up = <0>; diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts index 1ec8c94..2474207 100644 --- a/arch/arm/boot/dts/imx28-cfa10036.dts +++ b/arch/arm/boot/dts/imx28-cfa10036.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "Crystalfontz CFA-10036 Board"; @@ -26,7 +26,7 @@ ssd1306_cfa10036: ssd1306-10036@0 { reg = <0>; fsl,pinmux-ids = < - 0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */ + MX28_PAD_SSP0_DATA7__GPIO_2_7 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -36,7 +36,7 @@ led_pins_cfa10036: leds-10036@0 { reg = <0>; fsl,pinmux-ids = < - 0x3043 /* MX28_PAD_AUART1_RX__GPIO_3_4 */ + MX28_PAD_AUART1_RX__GPIO_3_4 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -46,7 +46,7 @@ usb0_otg_cfa10036: otg-10036@0 { reg = <0>; fsl,pinmux-ids = < - 0x0142 /* MX28_PAD_GPMI_READY0__USB0_ID */ + MX28_PAD_GPMI_RDY0__USB0_ID >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts index 182b99f..42a9a99 100644 --- a/arch/arm/boot/dts/imx28-cfa10037.dts +++ b/arch/arm/boot/dts/imx28-cfa10037.dts @@ -13,7 +13,7 @@ * The CFA-10049 is an expansion board for the CFA-10036 module, thus we * need to include the CFA-10036 DTS. */ -/include/ "imx28-cfa10036.dts" +#include "imx28-cfa10036.dts" / { model = "Crystalfontz CFA-10037 Board"; @@ -25,7 +25,7 @@ usb_pins_cfa10037: usb-10037@0 { reg = <0>; fsl,pinmux-ids = < - 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + MX28_PAD_GPMI_D07__GPIO_0_7 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -35,7 +35,7 @@ mac0_pins_cfa10037: mac0-10037@0 { reg = <0>; fsl,pinmux-ids = < - 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */ + MX28_PAD_SSP2_SS2__GPIO_2_21 >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts index 06e4cfa..9ee2566 100644 --- a/arch/arm/boot/dts/imx28-cfa10049.dts +++ b/arch/arm/boot/dts/imx28-cfa10049.dts @@ -13,7 +13,7 @@ * The CFA-10049 is an expansion board for the CFA-10036 module, thus we * need to include the CFA-10036 DTS. */ -/include/ "imx28-cfa10036.dts" +#include "imx28-cfa10036.dts" / { model = "Crystalfontz CFA-10049 Board"; @@ -25,7 +25,7 @@ usb_pins_cfa10049: usb-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + MX28_PAD_GPMI_D07__GPIO_0_7 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -35,8 +35,8 @@ i2cmux_pins_cfa10049: i2cmux-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */ - 0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */ + MX28_PAD_LCD_D22__GPIO_1_22 + MX28_PAD_LCD_D23__GPIO_1_23 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -46,7 +46,7 @@ mac0_pins_cfa10049: mac0-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */ + MX28_PAD_SSP2_SS2__GPIO_2_21 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -56,7 +56,7 @@ pca_pins_cfa10049: pca-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */ + MX28_PAD_SSP2_SS0__GPIO_2_19 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -66,8 +66,8 @@ rotary_pins_cfa10049: rotary-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */ - 0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */ + MX28_PAD_I2C0_SCL__GPIO_3_24 + MX28_PAD_I2C0_SDA__GPIO_3_25 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -77,7 +77,7 @@ rotary_btn_pins_cfa10049: rotary-btn-10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */ + MX28_PAD_SAIF1_SDATA0__GPIO_3_26 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -87,10 +87,10 @@ spi2_pins_cfa10049: spi2-cfa10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */ - 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */ - 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */ - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_SSP2_SCK__GPIO_2_16 + MX28_PAD_SSP2_MOSI__GPIO_2_17 + MX28_PAD_SSP2_MISO__GPIO_2_18 + MX28_PAD_AUART1_TX__GPIO_3_5 >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -100,11 +100,11 @@ spi3_pins_cfa10049: spi3-cfa10049@0 { reg = <0>; fsl,pinmux-ids = < - 0x0183 /* MX28_PAD_GPMI_RDN__GPIO_0_24 */ - 0x01c3 /* MX28_PAD_GPMI_RESETN__GPIO_0_28 */ - 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */ - 0x01a3 /* MX28_PAD_GPMI_ALE__GPIO_0_26 */ - 0x01b3 /* MX28_PAD_GPMI_CLE__GPIO_0_27 */ + MX28_PAD_GPMI_RDN__GPIO_0_24 + MX28_PAD_GPMI_RESETN__GPIO_0_28 + MX28_PAD_GPMI_CE1N__GPIO_0_17 + MX28_PAD_GPMI_ALE__GPIO_0_26 + MX28_PAD_GPMI_CLE__GPIO_0_27 >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -114,24 +114,24 @@ lcdif_18bit_pins_cfa10049: lcdif-18bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -141,10 +141,10 @@ lcdif_pins_cfa10049: lcdif-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -154,7 +154,7 @@ lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 { reg = <0>; fsl,pinmux-ids = < - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + MX28_PAD_LCD_RESET__GPIO_3_30 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -164,7 +164,7 @@ w1_gpio_pins: w1-gpio@0 { reg = <0>; fsl,pinmux-ids = < - 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */ + MX28_PAD_LCD_D21__GPIO_1_21 >; fsl,drive-strength = <1>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts index 171bcbe..8b262a2 100644 --- a/arch/arm/boot/dts/imx28-cfa10055.dts +++ b/arch/arm/boot/dts/imx28-cfa10055.dts @@ -14,7 +14,7 @@ * The CFA-10055 is an expansion board for the CFA-10036 module and * CFA-10037, thus we need to include the CFA-10037 DTS. */ -/include/ "imx28-cfa10037.dts" +#include "imx28-cfa10037.dts" / { model = "Crystalfontz CFA-10055 Board"; @@ -26,10 +26,10 @@ spi2_pins_cfa10055: spi2-cfa10055@0 { reg = <0>; fsl,pinmux-ids = < - 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */ - 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */ - 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */ - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_SSP2_SCK__GPIO_2_16 + MX28_PAD_SSP2_MOSI__GPIO_2_17 + MX28_PAD_SSP2_MISO__GPIO_2_18 + MX28_PAD_AUART1_TX__GPIO_3_5 >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -39,24 +39,24 @@ lcdif_18bit_pins_cfa10055: lcdif-18bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -66,10 +66,10 @@ lcdif_pins_cfa10055: lcdif-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -79,7 +79,7 @@ lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 { reg = <0>; fsl,pinmux-ids = < - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + MX28_PAD_LCD_RESET__GPIO_3_30 >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts index b45dd0e..f651998 100644 --- a/arch/arm/boot/dts/imx28-cfa10056.dts +++ b/arch/arm/boot/dts/imx28-cfa10056.dts @@ -13,7 +13,7 @@ * The CFA-10055 is an expansion board for the CFA-10036 module and * CFA-10037, thus we need to include the CFA-10037 DTS. */ -/include/ "imx28-cfa10037.dts" +#include "imx28-cfa10037.dts" / { model = "Crystalfontz CFA-10056 Board"; @@ -25,10 +25,10 @@ spi2_pins_cfa10056: spi2-cfa10056@0 { reg = <0>; fsl,pinmux-ids = < - 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */ - 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */ - 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */ - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_SSP2_SCK__GPIO_2_16 + MX28_PAD_SSP2_MOSI__GPIO_2_17 + MX28_PAD_SSP2_MISO__GPIO_2_18 + MX28_PAD_AUART1_TX__GPIO_3_5 >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -38,10 +38,10 @@ lcdif_pins_cfa10056: lcdif-10056@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -51,7 +51,7 @@ lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 { reg = <0>; fsl,pinmux-ids = < - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + MX28_PAD_LCD_RESET__GPIO_3_30 >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts index 0333c05..76430ca 100644 --- a/arch/arm/boot/dts/imx28-cfa10057.dts +++ b/arch/arm/boot/dts/imx28-cfa10057.dts @@ -14,7 +14,7 @@ * The CFA-10057 is an expansion board for the CFA-10036 module, thus we * need to include the CFA-10036 DTS. */ -/include/ "imx28-cfa10036.dts" +#include "imx28-cfa10036.dts" / { model = "Crystalfontz CFA-10057 Board"; @@ -26,7 +26,7 @@ usb_pins_cfa10057: usb-10057@0 { reg = <0>; fsl,pinmux-ids = < - 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + MX28_PAD_GPMI_D07__GPIO_0_7 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -36,24 +36,24 @@ lcdif_18bit_pins_cfa10057: lcdif-18bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -63,10 +63,10 @@ lcdif_pins_cfa10057: lcdif-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts index 64c64c5..502be77 100644 --- a/arch/arm/boot/dts/imx28-cfa10058.dts +++ b/arch/arm/boot/dts/imx28-cfa10058.dts @@ -14,7 +14,7 @@ * The CFA-10058 is an expansion board for the CFA-10036 module, thus we * need to include the CFA-10036 DTS. */ -/include/ "imx28-cfa10036.dts" +#include "imx28-cfa10036.dts" / { model = "Crystalfontz CFA-10058 Board"; @@ -26,7 +26,7 @@ usb_pins_cfa10058: usb-10058@0 { reg = <0>; fsl,pinmux-ids = < - 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */ + MX28_PAD_GPMI_D07__GPIO_0_7 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -36,10 +36,10 @@ lcdif_pins_cfa10058: lcdif-10058@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index 15715d9..dff2279 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "Freescale i.MX28 Evaluation Kit"; @@ -70,14 +70,14 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */ - 0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */ - 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */ - 0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */ - 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */ - 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ - 0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */ - 0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */ + MX28_PAD_SSP1_CMD__GPIO_2_13 + MX28_PAD_SSP1_DATA3__GPIO_2_15 + MX28_PAD_ENET0_RX_CLK__GPIO_4_13 + MX28_PAD_SSP1_SCK__GPIO_2_12 + MX28_PAD_PWM3__GPIO_3_28 + MX28_PAD_LCD_RESET__GPIO_3_30 + MX28_PAD_AUART2_RX__GPIO_3_8 + MX28_PAD_AUART2_TX__GPIO_3_9 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -87,7 +87,7 @@ led_pin_gpio3_5: led_gpio3_5@0 { reg = <0>; fsl,pinmux-ids = < - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_AUART1_TX__GPIO_3_5 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -97,8 +97,8 @@ gpmi_pins_evk: gpmi-nand-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */ - 0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */ + MX28_PAD_GPMI_CE1N__GPMI_CE1N + MX28_PAD_GPMI_RDY1__GPMI_READY1 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -108,10 +108,10 @@ lcdif_pins_evk: lcdif-evk@0 { reg = <0>; fsl,pinmux-ids = < - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts index 0d322a2..9f3271d 100644 --- a/arch/arm/boot/dts/imx28-m28evk.dts +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "DENX M28EVK"; @@ -92,11 +92,11 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */ - 0x30a3 /* MX28_PAD_AUART2_CTS__GPIO_3_10 */ - 0x30b3 /* MX28_PAD_AUART2_RTS__GPIO_3_11 */ - 0x30c3 /* MX28_PAD_AUART3_RX__GPIO_3_12 */ - 0x30d3 /* MX28_PAD_AUART3_TX__GPIO_3_13 */ + MX28_PAD_PWM3__GPIO_3_28 + MX28_PAD_AUART2_CTS__GPIO_3_10 + MX28_PAD_AUART2_RTS__GPIO_3_11 + MX28_PAD_AUART3_RX__GPIO_3_12 + MX28_PAD_AUART3_TX__GPIO_3_13 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -106,8 +106,8 @@ lcdif_pins_m28: lcdif-m28@0 { reg = <0>; fsl,pinmux-ids = < - 0x11e0 /* MX28_PAD_LCD_DOTCLK__LCD_DOTCLK */ - 0x11f0 /* MX28_PAD_LCD_ENABLE__LCD_ENABLE */ + MX28_PAD_LCD_DOTCLK__LCD_DOTCLK + MX28_PAD_LCD_ENABLE__LCD_ENABLE >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts index 6c6a544..4613522 100644 --- a/arch/arm/boot/dts/imx28-sps1.dts +++ b/arch/arm/boot/dts/imx28-sps1.dts @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "imx28.dtsi" +#include "imx28.dtsi" / { model = "SchulerControl GmbH, SC SPS 1"; @@ -29,9 +29,9 @@ hog_pins_a: hog-gpios@0 { reg = <0>; fsl,pinmux-ids = < - 0x0003 /* MX28_PAD_GPMI_D00__GPIO_0_0 */ - 0x0033 /* MX28_PAD_GPMI_D03__GPIO_0_3 */ - 0x0063 /* MX28_PAD_GPMI_D06__GPIO_0_6 */ + MX28_PAD_GPMI_D00__GPIO_0_0 + MX28_PAD_GPMI_D03__GPIO_0_3 + MX28_PAD_GPMI_D06__GPIO_0_6 >; fsl,drive-strength = <0>; fsl,voltage = <1>; diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 11e9840..14344c0 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -9,7 +9,8 @@ * http://www.gnu.org/copyleft/gpl.html */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" +#include "imx28-pinfunc.h" / { interrupt-parent = <&icoll>; @@ -207,8 +208,8 @@ duart_pins_a: duart@0 { reg = <0>; fsl,pinmux-ids = < - 0x3102 /* MX28_PAD_PWM0__DUART_RX */ - 0x3112 /* MX28_PAD_PWM1__DUART_TX */ + MX28_PAD_PWM0__DUART_RX + MX28_PAD_PWM1__DUART_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -218,8 +219,8 @@ duart_pins_b: duart@1 { reg = <1>; fsl,pinmux-ids = < - 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */ - 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */ + MX28_PAD_AUART0_CTS__DUART_RX + MX28_PAD_AUART0_RTS__DUART_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -229,10 +230,10 @@ duart_4pins_a: duart-4pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */ - 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */ - 0x3002 /* MX28_PAD_AUART0_RX__DUART_CTS */ - 0x3012 /* MX28_PAD_AUART0_TX__DUART_RTS */ + MX28_PAD_AUART0_CTS__DUART_RX + MX28_PAD_AUART0_RTS__DUART_TX + MX28_PAD_AUART0_RX__DUART_CTS + MX28_PAD_AUART0_TX__DUART_RTS >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -242,21 +243,21 @@ gpmi_pins_a: gpmi-nand@0 { reg = <0>; fsl,pinmux-ids = < - 0x0000 /* MX28_PAD_GPMI_D00__GPMI_D0 */ - 0x0010 /* MX28_PAD_GPMI_D01__GPMI_D1 */ - 0x0020 /* MX28_PAD_GPMI_D02__GPMI_D2 */ - 0x0030 /* MX28_PAD_GPMI_D03__GPMI_D3 */ - 0x0040 /* MX28_PAD_GPMI_D04__GPMI_D4 */ - 0x0050 /* MX28_PAD_GPMI_D05__GPMI_D5 */ - 0x0060 /* MX28_PAD_GPMI_D06__GPMI_D6 */ - 0x0070 /* MX28_PAD_GPMI_D07__GPMI_D7 */ - 0x0100 /* MX28_PAD_GPMI_CE0N__GPMI_CE0N */ - 0x0140 /* MX28_PAD_GPMI_RDY0__GPMI_READY0 */ - 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */ - 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */ - 0x01a0 /* MX28_PAD_GPMI_ALE__GPMI_ALE */ - 0x01b0 /* MX28_PAD_GPMI_CLE__GPMI_CLE */ - 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */ + MX28_PAD_GPMI_D00__GPMI_D0 + MX28_PAD_GPMI_D01__GPMI_D1 + MX28_PAD_GPMI_D02__GPMI_D2 + MX28_PAD_GPMI_D03__GPMI_D3 + MX28_PAD_GPMI_D04__GPMI_D4 + MX28_PAD_GPMI_D05__GPMI_D5 + MX28_PAD_GPMI_D06__GPMI_D6 + MX28_PAD_GPMI_D07__GPMI_D7 + MX28_PAD_GPMI_CE0N__GPMI_CE0N + MX28_PAD_GPMI_RDY0__GPMI_READY0 + MX28_PAD_GPMI_RDN__GPMI_RDN + MX28_PAD_GPMI_WRN__GPMI_WRN + MX28_PAD_GPMI_ALE__GPMI_ALE + MX28_PAD_GPMI_CLE__GPMI_CLE + MX28_PAD_GPMI_RESETN__GPMI_RESETN >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -265,9 +266,9 @@ gpmi_status_cfg: gpmi-status-cfg { fsl,pinmux-ids = < - 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */ - 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */ - 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */ + MX28_PAD_GPMI_RDN__GPMI_RDN + MX28_PAD_GPMI_WRN__GPMI_WRN + MX28_PAD_GPMI_RESETN__GPMI_RESETN >; fsl,drive-strength = <2>; }; @@ -275,10 +276,10 @@ auart0_pins_a: auart0@0 { reg = <0>; fsl,pinmux-ids = < - 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */ - 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */ - 0x3020 /* MX28_PAD_AUART0_CTS__AUART0_CTS */ - 0x3030 /* MX28_PAD_AUART0_RTS__AUART0_RTS */ + MX28_PAD_AUART0_RX__AUART0_RX + MX28_PAD_AUART0_TX__AUART0_TX + MX28_PAD_AUART0_CTS__AUART0_CTS + MX28_PAD_AUART0_RTS__AUART0_RTS >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -288,8 +289,8 @@ auart0_2pins_a: auart0-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */ - 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */ + MX28_PAD_AUART0_RX__AUART0_RX + MX28_PAD_AUART0_TX__AUART0_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -299,10 +300,10 @@ auart1_pins_a: auart1@0 { reg = <0>; fsl,pinmux-ids = < - 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */ - 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */ - 0x3060 /* MX28_PAD_AUART1_CTS__AUART1_CTS */ - 0x3070 /* MX28_PAD_AUART1_RTS__AUART1_RTS */ + MX28_PAD_AUART1_RX__AUART1_RX + MX28_PAD_AUART1_TX__AUART1_TX + MX28_PAD_AUART1_CTS__AUART1_CTS + MX28_PAD_AUART1_RTS__AUART1_RTS >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -312,8 +313,8 @@ auart1_2pins_a: auart1-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */ - 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */ + MX28_PAD_AUART1_RX__AUART1_RX + MX28_PAD_AUART1_TX__AUART1_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -323,8 +324,8 @@ auart2_2pins_a: auart2-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x2101 /* MX28_PAD_SSP2_SCK__AUART2_RX */ - 0x2111 /* MX28_PAD_SSP2_MOSI__AUART2_TX */ + MX28_PAD_SSP2_SCK__AUART2_RX + MX28_PAD_SSP2_MOSI__AUART2_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -334,8 +335,8 @@ auart2_2pins_b: auart2-2pins@1 { reg = <1>; fsl,pinmux-ids = < - 0x3080 /* MX28_PAD_AUART2_RX__AUART2_RX */ - 0x3090 /* MX28_PAD_AUART2_TX__AUART2_TX */ + MX28_PAD_AUART2_RX__AUART2_RX + MX28_PAD_AUART2_TX__AUART2_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -345,10 +346,10 @@ auart3_pins_a: auart3@0 { reg = <0>; fsl,pinmux-ids = < - 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */ - 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */ - 0x30e0 /* MX28_PAD_AUART3_CTS__AUART3_CTS */ - 0x30f0 /* MX28_PAD_AUART3_RTS__AUART3_RTS */ + MX28_PAD_AUART3_RX__AUART3_RX + MX28_PAD_AUART3_TX__AUART3_TX + MX28_PAD_AUART3_CTS__AUART3_CTS + MX28_PAD_AUART3_RTS__AUART3_RTS >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -358,8 +359,8 @@ auart3_2pins_a: auart3-2pins@0 { reg = <0>; fsl,pinmux-ids = < - 0x2121 /* MX28_PAD_SSP2_MISO__AUART3_RX */ - 0x2131 /* MX28_PAD_SSP2_SS0__AUART3_TX */ + MX28_PAD_SSP2_MISO__AUART3_RX + MX28_PAD_SSP2_SS0__AUART3_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -369,8 +370,8 @@ auart3_2pins_b: auart3-2pins@1 { reg = <1>; fsl,pinmux-ids = < - 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */ - 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */ + MX28_PAD_AUART3_RX__AUART3_RX + MX28_PAD_AUART3_TX__AUART3_TX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -380,8 +381,8 @@ auart4_2pins_a: auart4@0 { reg = <0>; fsl,pinmux-ids = < - 0x2181 /* MX28_PAD_SSP3_SCK__AUART4_TX */ - 0x2191 /* MX28_PAD_SSP3_MOSI__AUART4_RX */ + MX28_PAD_SSP3_SCK__AUART4_TX + MX28_PAD_SSP3_MOSI__AUART4_RX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -391,15 +392,15 @@ mac0_pins_a: mac0@0 { reg = <0>; fsl,pinmux-ids = < - 0x4000 /* MX28_PAD_ENET0_MDC__ENET0_MDC */ - 0x4010 /* MX28_PAD_ENET0_MDIO__ENET0_MDIO */ - 0x4020 /* MX28_PAD_ENET0_RX_EN__ENET0_RX_EN */ - 0x4030 /* MX28_PAD_ENET0_RXD0__ENET0_RXD0 */ - 0x4040 /* MX28_PAD_ENET0_RXD1__ENET0_RXD1 */ - 0x4060 /* MX28_PAD_ENET0_TX_EN__ENET0_TX_EN */ - 0x4070 /* MX28_PAD_ENET0_TXD0__ENET0_TXD0 */ - 0x4080 /* MX28_PAD_ENET0_TXD1__ENET0_TXD1 */ - 0x4100 /* MX28_PAD_ENET_CLK__CLKCTRL_ENET */ + MX28_PAD_ENET0_MDC__ENET0_MDC + MX28_PAD_ENET0_MDIO__ENET0_MDIO + MX28_PAD_ENET0_RX_EN__ENET0_RX_EN + MX28_PAD_ENET0_RXD0__ENET0_RXD0 + MX28_PAD_ENET0_RXD1__ENET0_RXD1 + MX28_PAD_ENET0_TX_EN__ENET0_TX_EN + MX28_PAD_ENET0_TXD0__ENET0_TXD0 + MX28_PAD_ENET0_TXD1__ENET0_TXD1 + MX28_PAD_ENET_CLK__CLKCTRL_ENET >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -409,12 +410,12 @@ mac1_pins_a: mac1@0 { reg = <0>; fsl,pinmux-ids = < - 0x40f1 /* MX28_PAD_ENET0_CRS__ENET1_RX_EN */ - 0x4091 /* MX28_PAD_ENET0_RXD2__ENET1_RXD0 */ - 0x40a1 /* MX28_PAD_ENET0_RXD3__ENET1_RXD1 */ - 0x40e1 /* MX28_PAD_ENET0_COL__ENET1_TX_EN */ - 0x40b1 /* MX28_PAD_ENET0_TXD2__ENET1_TXD0 */ - 0x40c1 /* MX28_PAD_ENET0_TXD3__ENET1_TXD1 */ + MX28_PAD_ENET0_CRS__ENET1_RX_EN + MX28_PAD_ENET0_RXD2__ENET1_RXD0 + MX28_PAD_ENET0_RXD3__ENET1_RXD1 + MX28_PAD_ENET0_COL__ENET1_TX_EN + MX28_PAD_ENET0_TXD2__ENET1_TXD0 + MX28_PAD_ENET0_TXD3__ENET1_TXD1 >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -424,17 +425,17 @@ mmc0_8bit_pins_a: mmc0-8bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */ - 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */ - 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */ - 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */ - 0x2040 /* MX28_PAD_SSP0_DATA4__SSP0_D4 */ - 0x2050 /* MX28_PAD_SSP0_DATA5__SSP0_D5 */ - 0x2060 /* MX28_PAD_SSP0_DATA6__SSP0_D6 */ - 0x2070 /* MX28_PAD_SSP0_DATA7__SSP0_D7 */ - 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */ - 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ - 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + MX28_PAD_SSP0_DATA0__SSP0_D0 + MX28_PAD_SSP0_DATA1__SSP0_D1 + MX28_PAD_SSP0_DATA2__SSP0_D2 + MX28_PAD_SSP0_DATA3__SSP0_D3 + MX28_PAD_SSP0_DATA4__SSP0_D4 + MX28_PAD_SSP0_DATA5__SSP0_D5 + MX28_PAD_SSP0_DATA6__SSP0_D6 + MX28_PAD_SSP0_DATA7__SSP0_D7 + MX28_PAD_SSP0_CMD__SSP0_CMD + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT + MX28_PAD_SSP0_SCK__SSP0_SCK >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -444,13 +445,13 @@ mmc0_4bit_pins_a: mmc0-4bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */ - 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */ - 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */ - 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */ - 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */ - 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ - 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + MX28_PAD_SSP0_DATA0__SSP0_D0 + MX28_PAD_SSP0_DATA1__SSP0_D1 + MX28_PAD_SSP0_DATA2__SSP0_D2 + MX28_PAD_SSP0_DATA3__SSP0_D3 + MX28_PAD_SSP0_CMD__SSP0_CMD + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT + MX28_PAD_SSP0_SCK__SSP0_SCK >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -459,14 +460,14 @@ mmc0_cd_cfg: mmc0-cd-cfg { fsl,pinmux-ids = < - 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ + MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT >; fsl,pull-up = <0>; }; mmc0_sck_cfg: mmc0-sck-cfg { fsl,pinmux-ids = < - 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + MX28_PAD_SSP0_SCK__SSP0_SCK >; fsl,drive-strength = <2>; fsl,pull-up = <0>; @@ -475,8 +476,8 @@ i2c0_pins_a: i2c0@0 { reg = <0>; fsl,pinmux-ids = < - 0x3180 /* MX28_PAD_I2C0_SCL__I2C0_SCL */ - 0x3190 /* MX28_PAD_I2C0_SDA__I2C0_SDA */ + MX28_PAD_I2C0_SCL__I2C0_SCL + MX28_PAD_I2C0_SDA__I2C0_SDA >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -486,8 +487,8 @@ i2c0_pins_b: i2c0@1 { reg = <1>; fsl,pinmux-ids = < - 0x3001 /* MX28_PAD_AUART0_RX__I2C0_SCL */ - 0x3011 /* MX28_PAD_AUART0_TX__I2C0_SDA */ + MX28_PAD_AUART0_RX__I2C0_SCL + MX28_PAD_AUART0_TX__I2C0_SDA >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -497,8 +498,8 @@ i2c1_pins_a: i2c1@0 { reg = <0>; fsl,pinmux-ids = < - 0x3101 /* MX28_PAD_PWM0__I2C1_SCL */ - 0x3111 /* MX28_PAD_PWM1__I2C1_SDA */ + MX28_PAD_PWM0__I2C1_SCL + MX28_PAD_PWM1__I2C1_SDA >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -508,10 +509,10 @@ saif0_pins_a: saif0@0 { reg = <0>; fsl,pinmux-ids = < - 0x3140 /* MX28_PAD_SAIF0_MCLK__SAIF0_MCLK */ - 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */ - 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */ - 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */ + MX28_PAD_SAIF0_MCLK__SAIF0_MCLK + MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK + MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK + MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 >; fsl,drive-strength = <2>; fsl,voltage = <1>; @@ -521,9 +522,9 @@ saif0_pins_b: saif0@1 { reg = <1>; fsl,pinmux-ids = < - 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */ - 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */ - 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */ + MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK + MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK + MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 >; fsl,drive-strength = <2>; fsl,voltage = <1>; @@ -545,7 +546,7 @@ saif1_pins_a: saif1@0 { reg = <0>; fsl,pinmux-ids = < - 0x31a0 /* MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 */ + MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 >; fsl,drive-strength = <2>; fsl,voltage = <1>; @@ -555,7 +556,7 @@ pwm0_pins_a: pwm0@0 { reg = <0>; fsl,pinmux-ids = < - 0x3100 /* MX28_PAD_PWM0__PWM_0 */ + MX28_PAD_PWM0__PWM_0 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -565,7 +566,7 @@ pwm2_pins_a: pwm2@0 { reg = <0>; fsl,pinmux-ids = < - 0x3120 /* MX28_PAD_PWM2__PWM_2 */ + MX28_PAD_PWM2__PWM_2 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -575,7 +576,7 @@ pwm3_pins_a: pwm3@0 { reg = <0>; fsl,pinmux-ids = < - 0x31c0 /* MX28_PAD_PWM3__PWM_3 */ + MX28_PAD_PWM3__PWM_3 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -585,7 +586,7 @@ pwm3_pins_b: pwm3@1 { reg = <1>; fsl,pinmux-ids = < - 0x3141 /* MX28_PAD_SAIF0_MCLK__PWM3 */ + MX28_PAD_SAIF0_MCLK__PWM_3 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -595,7 +596,7 @@ pwm4_pins_a: pwm4@0 { reg = <0>; fsl,pinmux-ids = < - 0x31d0 /* MX28_PAD_PWM4__PWM_4 */ + MX28_PAD_PWM4__PWM_4 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -605,30 +606,30 @@ lcdif_24bit_pins_a: lcdif-24bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ - 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ - 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ - 0x1120 /* MX28_PAD_LCD_D18__LCD_D18 */ - 0x1130 /* MX28_PAD_LCD_D19__LCD_D19 */ - 0x1140 /* MX28_PAD_LCD_D20__LCD_D20 */ - 0x1150 /* MX28_PAD_LCD_D21__LCD_D21 */ - 0x1160 /* MX28_PAD_LCD_D22__LCD_D22 */ - 0x1170 /* MX28_PAD_LCD_D23__LCD_D23 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 + MX28_PAD_LCD_D18__LCD_D18 + MX28_PAD_LCD_D19__LCD_D19 + MX28_PAD_LCD_D20__LCD_D20 + MX28_PAD_LCD_D21__LCD_D21 + MX28_PAD_LCD_D22__LCD_D22 + MX28_PAD_LCD_D23__LCD_D23 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -638,22 +639,22 @@ lcdif_16bit_pins_a: lcdif-16bit@0 { reg = <0>; fsl,pinmux-ids = < - 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ - 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ - 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ - 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ - 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ - 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ - 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ - 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ - 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ - 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ - 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ - 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ - 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ - 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ - 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ - 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -663,10 +664,10 @@ lcdif_sync_pins_a: lcdif-sync@0 { reg = <0>; fsl,pinmux-ids = < - 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ - 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ - 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ - 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ + MX28_PAD_LCD_RS__LCD_DOTCLK + MX28_PAD_LCD_CS__LCD_ENABLE + MX28_PAD_LCD_RD_E__LCD_VSYNC + MX28_PAD_LCD_WR_RWN__LCD_HSYNC >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -689,8 +690,8 @@ can0_pins_a: can0@0 { reg = <0>; fsl,pinmux-ids = < - 0x0161 /* MX28_PAD_GPMI_RDY2__CAN0_TX */ - 0x0171 /* MX28_PAD_GPMI_RDY3__CAN0_RX */ + MX28_PAD_GPMI_RDY2__CAN0_TX + MX28_PAD_GPMI_RDY3__CAN0_RX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -700,8 +701,8 @@ can1_pins_a: can1@0 { reg = <0>; fsl,pinmux-ids = < - 0x0121 /* MX28_PAD_GPMI_CE2N__CAN1_TX */ - 0x0131 /* MX28_PAD_GPMI_CE3N__CAN1_RX */ + MX28_PAD_GPMI_CE2N__CAN1_TX + MX28_PAD_GPMI_CE3N__CAN1_RX >; fsl,drive-strength = <0>; fsl,voltage = <1>; @@ -711,10 +712,10 @@ spi2_pins_a: spi2@0 { reg = <0>; fsl,pinmux-ids = < - 0x2100 /* MX28_PAD_SSP2_SCK__SSP2_SCK */ - 0x2110 /* MX28_PAD_SSP2_MOSI__SSP2_CMD */ - 0x2120 /* MX28_PAD_SSP2_MISO__SSP2_D0 */ - 0x2130 /* MX28_PAD_SSP2_SS0__SSP2_D3 */ + MX28_PAD_SSP2_SCK__SSP2_SCK + MX28_PAD_SSP2_MOSI__SSP2_CMD + MX28_PAD_SSP2_MISO__SSP2_D0 + MX28_PAD_SSP2_SS0__SSP2_D3 >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -724,12 +725,12 @@ spi3_pins_a: spi3@0 { reg = <0>; fsl,pinmux-ids = < - 0x3082 /* MX28_PAD_AUART2_RX__SSP3_D4 */ - 0x3092 /* MX28_PAD_AUART2_TX__SSP3_D5 */ - 0x2180 /* MX28_PAD_SSP3_SCK__SSP3_SCK */ - 0x2190 /* MX28_PAD_SSP3_MOSI__SSP3_CMD */ - 0x21A0 /* MX28_PAD_SSP3_MISO__SSP3_D0 */ - 0x21B0 /* MX28_PAD_SSP3_SS0__SSP3_D3 */ + MX28_PAD_AUART2_RX__SSP3_D4 + MX28_PAD_AUART2_TX__SSP3_D5 + MX28_PAD_SSP3_SCK__SSP3_SCK + MX28_PAD_SSP3_MOSI__SSP3_CMD + MX28_PAD_SSP3_MISO__SSP3_D0 + MX28_PAD_SSP3_SS0__SSP3_D3 >; fsl,drive-strength = <1>; fsl,voltage = <1>; @@ -739,7 +740,7 @@ usbphy0_pins_a: usbphy0@0 { reg = <0>; fsl,pinmux-ids = < - 0x2152 /* MX28_PAD_SSP2_SS2__USB0_OVERCURRENT */ + MX28_PAD_SSP2_SS2__USB0_OVERCURRENT >; fsl,drive-strength = <2>; fsl,voltage = <1>; @@ -749,7 +750,7 @@ usbphy0_pins_b: usbphy0@1 { reg = <1>; fsl,pinmux-ids = < - 0x3061 /* MX28_PAD_AUART1_CTS__USB0_OVERCURRENT */ + MX28_PAD_AUART1_CTS__USB0_OVERCURRENT >; fsl,drive-strength = <2>; fsl,voltage = <1>; @@ -759,7 +760,7 @@ usbphy1_pins_a: usbphy1@0 { reg = <0>; fsl,pinmux-ids = < - 0x2142 /* MX28_PAD_SSP2_SS1__USB1_OVERCURRENT */ + MX28_PAD_SSP2_SS1__USB1_OVERCURRENT >; fsl,drive-strength = <2>; fsl,voltage = <1>; -- 1.7.2.5 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html