Signed-off-by: Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/imx23-evk.dts | 10 +-
arch/arm/boot/dts/imx23-olinuxino.dts | 6 +-
arch/arm/boot/dts/imx23-stmp378x_devb.dts | 6 +-
arch/arm/boot/dts/imx23.dtsi | 163 +++++++-------
arch/arm/boot/dts/imx28-apf28.dts | 2 +-
arch/arm/boot/dts/imx28-apf28dev.dts | 24 +-
arch/arm/boot/dts/imx28-apx4devkit.dts | 38 ++--
arch/arm/boot/dts/imx28-cfa10036.dts | 8 +-
arch/arm/boot/dts/imx28-cfa10037.dts | 6 +-
arch/arm/boot/dts/imx28-cfa10049.dts | 84 ++++----
arch/arm/boot/dts/imx28-cfa10055.dts | 56 +++---
arch/arm/boot/dts/imx28-cfa10056.dts | 20 +-
arch/arm/boot/dts/imx28-cfa10057.dts | 48 ++--
arch/arm/boot/dts/imx28-cfa10058.dts | 12 +-
arch/arm/boot/dts/imx28-evk.dts | 32 ++--
arch/arm/boot/dts/imx28-m28evk.dts | 16 +-
arch/arm/boot/dts/imx28-sps1.dts | 8 +-
arch/arm/boot/dts/imx28-tx28.dts | 85 ++++----
arch/arm/boot/dts/imx28.dtsi | 345 +++++++++++++++--------------
19 files changed, 486 insertions(+), 483 deletions(-)
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts
index 185c7c0..fdd8b27 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/imx23-evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "Freescale i.MX23 Evaluation Kit";
@@ -45,10 +45,10 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1123 /* MX23_PAD_LCD_RESET__GPIO_1_18 */
- 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */
- 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
+ MX23_PAD_LCD_RESET__GPIO_1_18
+ MX23_PAD_PWM3__GPIO_1_29
+ MX23_PAD_PWM4__GPIO_1_30
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts
index fc766ae..f575434 100644
--- a/arch/arm/boot/dts/imx23-olinuxino.dts
+++ b/arch/arm/boot/dts/imx23-olinuxino.dts
@@ -12,7 +12,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "i.MX23 Olinuxino Low Cost Board";
@@ -40,7 +40,7 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0113 /* MX23_PAD_GPMI_ALE__GPIO_0_17 */
+ MX23_PAD_GPMI_ALE__GPIO_0_17
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -50,7 +50,7 @@
led_pin_gpio2_1: led_gpio2_1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2013 /* MX23_PAD_SSP1_DETECT__GPIO_2_1 */
+ MX23_PAD_SSP1_DETECT__GPIO_2_1
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/imx23-stmp378x_devb.dts
index 85c3864..2c8a9b0 100644
--- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts
+++ b/arch/arm/boot/dts/imx23-stmp378x_devb.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "Freescale STMP378x Development Board";
@@ -39,8 +39,8 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */
- 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */
+ MX23_PAD_PWM3__GPIO_1_29
+ MX23_PAD_PWM4__GPIO_1_30
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi
index 28b5ce2..1c2cb1c 100644
--- a/arch/arm/boot/dts/imx23.dtsi
+++ b/arch/arm/boot/dts/imx23.dtsi
@@ -9,7 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
+#include <dt-bindings/pinctrl/mx23.h>
/ {
interrupt-parent = <&icoll>;
@@ -137,8 +138,8 @@
duart_pins_a: duart@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11a2 /* MX23_PAD_PWM0__DUART_RX */
- 0x11b2 /* MX23_PAD_PWM1__DUART_TX */
+ MX23_PAD_PWM0__DUART_RX
+ MX23_PAD_PWM1__DUART_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -148,10 +149,10 @@
auart0_pins_a: auart0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x01c0 /* MX23_PAD_AUART1_RX__AUART1_RX */
- 0x01d0 /* MX23_PAD_AUART1_TX__AUART1_TX */
- 0x01a0 /* MX23_PAD_AUART1_CTS__AUART1_CTS */
- 0x01b0 /* MX23_PAD_AUART1_RTS__AUART1_RTS */
+ MX23_PAD_AUART1_RX__AUART1_RX
+ MX23_PAD_AUART1_TX__AUART1_TX
+ MX23_PAD_AUART1_CTS__AUART1_CTS
+ MX23_PAD_AUART1_RTS__AUART1_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -161,8 +162,8 @@
auart0_2pins_a: auart0-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x01e2 /* MX23_PAD_I2C_SCL__AUART1_TX */
- 0x01f2 /* MX23_PAD_I2C_SDA__AUART1_RX */
+ MX23_PAD_I2C_SCL__AUART1_TX
+ MX23_PAD_I2C_SDA__AUART1_RX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -172,23 +173,23 @@
gpmi_pins_a: gpmi-nand@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0000 /* MX23_PAD_GPMI_D00__GPMI_D00 */
- 0x0010 /* MX23_PAD_GPMI_D01__GPMI_D01 */
- 0x0020 /* MX23_PAD_GPMI_D02__GPMI_D02 */
- 0x0030 /* MX23_PAD_GPMI_D03__GPMI_D03 */
- 0x0040 /* MX23_PAD_GPMI_D04__GPMI_D04 */
- 0x0050 /* MX23_PAD_GPMI_D05__GPMI_D05 */
- 0x0060 /* MX23_PAD_GPMI_D06__GPMI_D06 */
- 0x0070 /* MX23_PAD_GPMI_D07__GPMI_D07 */
- 0x0100 /* MX23_PAD_GPMI_CLE__GPMI_CLE */
- 0x0110 /* MX23_PAD_GPMI_ALE__GPMI_ALE */
- 0x0130 /* MX23_PAD_GPMI_RDY0__GPMI_RDY0 */
- 0x0140 /* MX23_PAD_GPMI_RDY1__GPMI_RDY1 */
- 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */
- 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */
- 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */
- 0x21b0 /* MX23_PAD_GPMI_CE1N__GPMI_CE1N */
- 0x21c0 /* MX23_PAD_GPMI_CE0N__GPMI_CE0N */
+ MX23_PAD_GPMI_D00__GPMI_D00
+ MX23_PAD_GPMI_D01__GPMI_D01
+ MX23_PAD_GPMI_D02__GPMI_D02
+ MX23_PAD_GPMI_D03__GPMI_D03
+ MX23_PAD_GPMI_D04__GPMI_D04
+ MX23_PAD_GPMI_D05__GPMI_D05
+ MX23_PAD_GPMI_D06__GPMI_D06
+ MX23_PAD_GPMI_D07__GPMI_D07
+ MX23_PAD_GPMI_CLE__GPMI_CLE
+ MX23_PAD_GPMI_ALE__GPMI_ALE
+ MX23_PAD_GPMI_RDY0__GPMI_RDY0
+ MX23_PAD_GPMI_RDY1__GPMI_RDY1
+ MX23_PAD_GPMI_WPN__GPMI_WPN
+ MX23_PAD_GPMI_WRN__GPMI_WRN
+ MX23_PAD_GPMI_RDN__GPMI_RDN
+ MX23_PAD_GPMI_CE1N__GPMI_CE1N
+ MX23_PAD_GPMI_CE0N__GPMI_CE0N
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -197,9 +198,9 @@
gpmi_pins_fixup: gpmi-pins-fixup {
fsl,pinmux-ids = <
- 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */
- 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */
- 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */
+ MX23_PAD_GPMI_WPN__GPMI_WPN
+ MX23_PAD_GPMI_WRN__GPMI_WRN
+ MX23_PAD_GPMI_RDN__GPMI_RDN
>;
fsl,drive-strength = <2>;
};
@@ -207,12 +208,12 @@
mmc0_4bit_pins_a: mmc0-4bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */
- 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */
- 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
- 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
- 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DATA0__SSP1_DATA0
+ MX23_PAD_SSP1_DATA1__SSP1_DATA1
+ MX23_PAD_SSP1_DATA2__SSP1_DATA2
+ MX23_PAD_SSP1_DATA3__SSP1_DATA3
+ MX23_PAD_SSP1_CMD__SSP1_CMD
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -222,17 +223,17 @@
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */
- 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */
- 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
- 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
- 0x0082 /* MX23_PAD_GPMI_D08__SSP1_DATA4 */
- 0x0092 /* MX23_PAD_GPMI_D09__SSP1_DATA5 */
- 0x00a2 /* MX23_PAD_GPMI_D10__SSP1_DATA6 */
- 0x00b2 /* MX23_PAD_GPMI_D11__SSP1_DATA7 */
- 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DATA0__SSP1_DATA0
+ MX23_PAD_SSP1_DATA1__SSP1_DATA1
+ MX23_PAD_SSP1_DATA2__SSP1_DATA2
+ MX23_PAD_SSP1_DATA3__SSP1_DATA3
+ MX23_PAD_GPMI_D08__SSP1_DATA4
+ MX23_PAD_GPMI_D09__SSP1_DATA5
+ MX23_PAD_GPMI_D10__SSP1_DATA6
+ MX23_PAD_GPMI_D11__SSP1_DATA7
+ MX23_PAD_SSP1_CMD__SSP1_CMD
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -241,8 +242,8 @@
mmc0_pins_fixup: mmc0-pins-fixup {
fsl,pinmux-ids = <
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
fsl,pull-up = <0>;
};
@@ -250,7 +251,7 @@
pwm2_pins_a: pwm2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11c0 /* MX23_PAD_PWM2__PWM2 */
+ MX23_PAD_PWM2__PWM2
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -260,34 +261,34 @@
lcdif_24bit_pins_a: lcdif-24bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX23_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX23_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX23_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX23_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX23_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX23_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX23_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX23_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX23_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX23_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX23_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX23_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX23_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX23_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX23_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX23_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX23_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX23_PAD_LCD_D17__LCD_D17 */
- 0x0081 /* MX23_PAD_GPMI_D08__LCD_D18 */
- 0x0091 /* MX23_PAD_GPMI_D09__LCD_D19 */
- 0x00a1 /* MX23_PAD_GPMI_D10__LCD_D20 */
- 0x00b1 /* MX23_PAD_GPMI_D11__LCD_D21 */
- 0x00c1 /* MX23_PAD_GPMI_D12__LCD_D22 */
- 0x00d1 /* MX23_PAD_GPMI_D13__LCD_D23 */
- 0x1160 /* MX23_PAD_LCD_DOTCK__LCD_DOTCK */
- 0x1170 /* MX23_PAD_LCD_ENABLE__LCD_ENABLE */
- 0x1180 /* MX23_PAD_LCD_HSYNC__LCD_HSYNC */
- 0x1190 /* MX23_PAD_LCD_VSYNC__LCD_VSYNC */
+ MX23_PAD_LCD_D00__LCD_D00
+ MX23_PAD_LCD_D01__LCD_D01
+ MX23_PAD_LCD_D02__LCD_D02
+ MX23_PAD_LCD_D03__LCD_D03
+ MX23_PAD_LCD_D04__LCD_D04
+ MX23_PAD_LCD_D05__LCD_D05
+ MX23_PAD_LCD_D06__LCD_D06
+ MX23_PAD_LCD_D07__LCD_D07
+ MX23_PAD_LCD_D08__LCD_D08
+ MX23_PAD_LCD_D09__LCD_D09
+ MX23_PAD_LCD_D10__LCD_D10
+ MX23_PAD_LCD_D11__LCD_D11
+ MX23_PAD_LCD_D12__LCD_D12
+ MX23_PAD_LCD_D13__LCD_D13
+ MX23_PAD_LCD_D14__LCD_D14
+ MX23_PAD_LCD_D15__LCD_D15
+ MX23_PAD_LCD_D16__LCD_D16
+ MX23_PAD_LCD_D17__LCD_D17
+ MX23_PAD_GPMI_D08__LCD_D18
+ MX23_PAD_GPMI_D09__LCD_D19
+ MX23_PAD_GPMI_D10__LCD_D20
+ MX23_PAD_GPMI_D11__LCD_D21
+ MX23_PAD_GPMI_D12__LCD_D22
+ MX23_PAD_GPMI_D13__LCD_D23
+ MX23_PAD_LCD_DOTCK__LCD_DOTCK
+ MX23_PAD_LCD_ENABLE__LCD_ENABLE
+ MX23_PAD_LCD_HSYNC__LCD_HSYNC
+ MX23_PAD_LCD_VSYNC__LCD_VSYNC
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -297,10 +298,10 @@
spi2_pins_a: spi2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0182 /* MX23_PAD_GPMI_WRN__SSP2_SCK */
- 0x0142 /* MX23_PAD_GPMI_RDY1__SSP2_CMD */
- 0x0002 /* MX23_PAD_GPMI_D00__SSP2_DATA0 */
- 0x0032 /* MX23_PAD_GPMI_D03__SSP2_DATA3 */
+ MX23_PAD_GPMI_WRN__SSP2_SCK
+ MX23_PAD_GPMI_RDY1__SSP2_CMD
+ MX23_PAD_GPMI_D00__SSP2_DATA0
+ MX23_PAD_GPMI_D03__SSP2_DATA3
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts
index 7eb0758..7198fe3 100644
--- a/arch/arm/boot/dts/imx28-apf28.dts
+++ b/arch/arm/boot/dts/imx28-apf28.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Armadeus Systems APF28 module";
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
index b602494..7d923cc 100644
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ b/arch/arm/boot/dts/imx28-apf28dev.dts
@@ -10,7 +10,7 @@
*/
/* APF28Dev is a docking board for the APF28 SOM */
-/include/ "imx28-apf28.dts"
+#include "imx28-apf28.dts"
/ {
model = "Armadeus Systems APF28Dev docking/development board";
@@ -41,13 +41,13 @@
hog_pins_apf28dev: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1103 /* MX28_PAD_LCD_D16__GPIO_1_16 */
- 0x1113 /* MX28_PAD_LCD_D17__GPIO_1_17 */
- 0x1123 /* MX28_PAD_LCD_D18__GPIO_1_18 */
- 0x1133 /* MX28_PAD_LCD_D19__GPIO_1_19 */
- 0x1143 /* MX28_PAD_LCD_D20__GPIO_1_20 */
- 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
- 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
+ MX28_PAD_LCD_D16__GPIO_1_16
+ MX28_PAD_LCD_D17__GPIO_1_17
+ MX28_PAD_LCD_D18__GPIO_1_18
+ MX28_PAD_LCD_D19__GPIO_1_19
+ MX28_PAD_LCD_D20__GPIO_1_20
+ MX28_PAD_LCD_D21__GPIO_1_21
+ MX28_PAD_LCD_D22__GPIO_1_22
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -57,10 +57,10 @@
lcdif_pins_apf28dev: lcdif-apf28dev@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
index 0e7fed4..cb19dc1 100644
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ b/arch/arm/boot/dts/imx28-apx4devkit.dts
@@ -1,5 +1,5 @@
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Bluegiga APX4 Development Kit";
@@ -40,13 +40,13 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */
- 0x0153 /* MX28_PAD_GPMI_RDY1__GPIO_0_21 */
- 0x2123 /* MX28_PAD_SSP2_MISO__GPIO_2_18 */
- 0x2131 /* MX28_PAD_SSP2_SS0__GPIO_2_19 */
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
- 0x4143 /* MX28_PAD_JTAG_RTCK__GPIO_4_20 */
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_RDY1__GPIO_0_21
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_JTAG_RTCK__GPIO_4_20
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -56,10 +56,10 @@
lcdif_pins_apx4: lcdif-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -69,12 +69,12 @@
mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2041 /* MX28_PAD_SSP0_DATA4__SSP2_D0 */
- 0x2051 /* MX28_PAD_SSP0_DATA5__SSP2_D3 */
- 0x2061 /* MX28_PAD_SSP0_DATA6__SSP2_CMD */
- 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */
- 0x2141 /* MX28_PAD_SSP2_SS1__SSP2_D1 */
- 0x2151 /* MX28_PAD_SSP2_SS2__SSP2_D2 */
+ MX28_PAD_SSP0_DATA4__SSP2_D0
+ MX28_PAD_SSP0_DATA5__SSP2_D3
+ MX28_PAD_SSP0_DATA6__SSP2_CMD
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
+ MX28_PAD_SSP2_SS1__SSP2_D1
+ MX28_PAD_SSP2_SS2__SSP2_D2
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -83,7 +83,7 @@
mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 {
fsl,pinmux-ids = <
- 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
fsl,drive-strength = <2>;
fsl,pull-up = <0>;
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 1ec8c94..2474207 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Crystalfontz CFA-10036 Board";
@@ -26,7 +26,7 @@
ssd1306_cfa10036: ssd1306-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */
+ MX28_PAD_SSP0_DATA7__GPIO_2_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -36,7 +36,7 @@
led_pins_cfa10036: leds-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3043 /* MX28_PAD_AUART1_RX__GPIO_3_4 */
+ MX28_PAD_AUART1_RX__GPIO_3_4
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -46,7 +46,7 @@
usb0_otg_cfa10036: otg-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0142 /* MX28_PAD_GPMI_READY0__USB0_ID */
+ MX28_PAD_GPMI_RDY0__USB0_ID
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts
index 182b99f..42a9a99 100644
--- a/arch/arm/boot/dts/imx28-cfa10037.dts
+++ b/arch/arm/boot/dts/imx28-cfa10037.dts
@@ -13,7 +13,7 @@
* The CFA-10049 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10037 Board";
@@ -25,7 +25,7 @@
usb_pins_cfa10037: usb-10037@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -35,7 +35,7 @@
mac0_pins_cfa10037: mac0-10037@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
+ MX28_PAD_SSP2_SS2__GPIO_2_21
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 06e4cfa..9ee2566 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -13,7 +13,7 @@
* The CFA-10049 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10049 Board";
@@ -25,7 +25,7 @@
usb_pins_cfa10049: usb-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -35,8 +35,8 @@
i2cmux_pins_cfa10049: i2cmux-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
- 0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
+ MX28_PAD_LCD_D22__GPIO_1_22
+ MX28_PAD_LCD_D23__GPIO_1_23
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -46,7 +46,7 @@
mac0_pins_cfa10049: mac0-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
+ MX28_PAD_SSP2_SS2__GPIO_2_21
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -56,7 +56,7 @@
pca_pins_cfa10049: pca-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
+ MX28_PAD_SSP2_SS0__GPIO_2_19
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -66,8 +66,8 @@
rotary_pins_cfa10049: rotary-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
- 0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -77,7 +77,7 @@
rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
+ MX28_PAD_SAIF1_SDATA0__GPIO_3_26
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -87,10 +87,10 @@
spi2_pins_cfa10049: spi2-cfa10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -100,11 +100,11 @@
spi3_pins_cfa10049: spi3-cfa10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0183 /* MX28_PAD_GPMI_RDN__GPIO_0_24 */
- 0x01c3 /* MX28_PAD_GPMI_RESETN__GPIO_0_28 */
- 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */
- 0x01a3 /* MX28_PAD_GPMI_ALE__GPIO_0_26 */
- 0x01b3 /* MX28_PAD_GPMI_CLE__GPIO_0_27 */
+ MX28_PAD_GPMI_RDN__GPIO_0_24
+ MX28_PAD_GPMI_RESETN__GPIO_0_28
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_ALE__GPIO_0_26
+ MX28_PAD_GPMI_CLE__GPIO_0_27
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -114,24 +114,24 @@
lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -141,10 +141,10 @@
lcdif_pins_cfa10049: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -154,7 +154,7 @@
lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -164,7 +164,7 @@
w1_gpio_pins: w1-gpio@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
+ MX28_PAD_LCD_D21__GPIO_1_21
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index 171bcbe..8b262a2 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -14,7 +14,7 @@
* The CFA-10055 is an expansion board for the CFA-10036 module and
* CFA-10037, thus we need to include the CFA-10037 DTS.
*/
-/include/ "imx28-cfa10037.dts"
+#include "imx28-cfa10037.dts"
/ {
model = "Crystalfontz CFA-10055 Board";
@@ -26,10 +26,10 @@
spi2_pins_cfa10055: spi2-cfa10055@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -39,24 +39,24 @@
lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -66,10 +66,10 @@
lcdif_pins_cfa10055: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -79,7 +79,7 @@
lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
index b45dd0e..f651998 100644
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -13,7 +13,7 @@
* The CFA-10055 is an expansion board for the CFA-10036 module and
* CFA-10037, thus we need to include the CFA-10037 DTS.
*/
-/include/ "imx28-cfa10037.dts"
+#include "imx28-cfa10037.dts"
/ {
model = "Crystalfontz CFA-10056 Board";
@@ -25,10 +25,10 @@
spi2_pins_cfa10056: spi2-cfa10056@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -38,10 +38,10 @@
lcdif_pins_cfa10056: lcdif-10056@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -51,7 +51,7 @@
lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 0333c05..76430ca 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -14,7 +14,7 @@
* The CFA-10057 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10057 Board";
@@ -26,7 +26,7 @@
usb_pins_cfa10057: usb-10057@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -36,24 +36,24 @@
lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -63,10 +63,10 @@
lcdif_pins_cfa10057: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
index 64c64c5..502be77 100644
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -14,7 +14,7 @@
* The CFA-10058 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10058 Board";
@@ -26,7 +26,7 @@
usb_pins_cfa10058: usb-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -36,10 +36,10 @@
lcdif_pins_cfa10058: lcdif-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 15715d9..dff2279 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Freescale i.MX28 Evaluation Kit";
@@ -70,14 +70,14 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */
- 0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */
- 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */
- 0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
- 0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */
- 0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP1_DATA3__GPIO_2_15
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_AUART2_TX__GPIO_3_9
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -87,7 +87,7 @@
led_pin_gpio3_5: led_gpio3_5@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -97,8 +97,8 @@
gpmi_pins_evk: gpmi-nand-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */
- 0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */
+ MX28_PAD_GPMI_CE1N__GPMI_CE1N
+ MX28_PAD_GPMI_RDY1__GPMI_READY1
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -108,10 +108,10 @@
lcdif_pins_evk: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
index 0d322a2..9f3271d 100644
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ b/arch/arm/boot/dts/imx28-m28evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "DENX M28EVK";
@@ -92,11 +92,11 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x30a3 /* MX28_PAD_AUART2_CTS__GPIO_3_10 */
- 0x30b3 /* MX28_PAD_AUART2_RTS__GPIO_3_11 */
- 0x30c3 /* MX28_PAD_AUART3_RX__GPIO_3_12 */
- 0x30d3 /* MX28_PAD_AUART3_TX__GPIO_3_13 */
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_AUART2_CTS__GPIO_3_10
+ MX28_PAD_AUART2_RTS__GPIO_3_11
+ MX28_PAD_AUART3_RX__GPIO_3_12
+ MX28_PAD_AUART3_TX__GPIO_3_13
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -106,8 +106,8 @@
lcdif_pins_m28: lcdif-m28@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11e0 /* MX28_PAD_LCD_DOTCLK__LCD_DOTCLK */
- 0x11f0 /* MX28_PAD_LCD_ENABLE__LCD_ENABLE */
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
index 6c6a544..4613522 100644
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ b/arch/arm/boot/dts/imx28-sps1.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "SchulerControl GmbH, SC SPS 1";
@@ -29,9 +29,9 @@
hog_pins_a: hog-gpios@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0003 /* MX28_PAD_GPMI_D00__GPIO_0_0 */
- 0x0033 /* MX28_PAD_GPMI_D03__GPIO_0_3 */
- 0x0063 /* MX28_PAD_GPMI_D06__GPIO_0_6 */
+ MX28_PAD_GPMI_D00__GPIO_0_0
+ MX28_PAD_GPMI_D03__GPIO_0_3
+ MX28_PAD_GPMI_D06__GPIO_0_6
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts
index 866af60..a82ac3d 100644
--- a/arch/arm/boot/dts/imx28-tx28.dts
+++ b/arch/arm/boot/dts/imx28-tx28.dts
@@ -11,7 +11,8 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Ka-Ro electronics TX28 module";
@@ -457,9 +458,9 @@
edt_ft5x06_pins: edt-ft5x06-pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2063 /* MX28_PAD_SSP0_DATA6__GPIO_2_6 - RESET */
- 0x2053 /* MX28_PAD_SSP0_DATA5__GPIO_2_5 - IRQ */
- 0x4093 /* MX28_PAD_ENET0_RXD2__GPIO_4_9 - WAKE */
+ MX28_PAD_SSP0_DATA6__GPIO_2_6 /* RESET */
+ MX28_PAD_SSP0_DATA5__GPIO_2_5 /* IRQ */
+ MX28_PAD_ENET0_RXD2__GPIO_4_9 /* WAKE */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -469,7 +470,7 @@
flexcan_xcvr_pins_a: flexcan-xcvr {
reg = <0>;
fsl,pinmux-ids = <
- 0x1003 /* MX28_PAD_LCD_D00__GPIO_1_0 */
+ MX28_PAD_LCD_D00__GPIO_1_0
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -479,7 +480,7 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x40a3 /* MX28_PAD_ENET0_RXD3__GPIO_4_10 - module LED */
+ MX28_PAD_ENET0_RXD3__GPIO_4_10 /* module LED */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -490,29 +491,29 @@
reg = <0>;
fsl,pinmux-ids = <
/* LCD_D00 may be used as Flexcan Transceiver Enable on STK5-V5 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
- 0x1120 /* MX28_PAD_LCD_D18__LCD_D18 */
- 0x1130 /* MX28_PAD_LCD_D19__LCD_D19 */
- 0x1140 /* MX28_PAD_LCD_D20__LCD_D20 */
- 0x1150 /* MX28_PAD_LCD_D21__LCD_D21 */
- 0x1160 /* MX28_PAD_LCD_D22__LCD_D22 */
- 0x1170 /* MX28_PAD_LCD_D23__LCD_D23 */
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ MX28_PAD_LCD_D18__LCD_D18
+ MX28_PAD_LCD_D19__LCD_D19
+ MX28_PAD_LCD_D20__LCD_D20
+ MX28_PAD_LCD_D21__LCD_D21
+ MX28_PAD_LCD_D22__LCD_D22
+ MX28_PAD_LCD_D23__LCD_D23
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -522,8 +523,8 @@
lcdif_ctrl_pins_a: lcdif-ctrl@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11f3 /* MX28_PAD_LCD_ENABLE__GPIO_1_31 - Enable */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 - Reset */
+ MX28_PAD_LCD_ENABLE__GPIO_1_31 /* Enable */
+ MX28_PAD_LCD_RESET__GPIO_3_30 /* Reset */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -533,15 +534,15 @@
mac0_pins_gpio: mac0-gpio-mode@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x4003 /* MX28_PAD_ENET0_MDC__GPIO_4_0 */
- 0x4013 /* MX28_PAD_ENET0_MDIO__GPIO_4_1 */
- 0x4023 /* MX28_PAD_ENET0_RX_EN__GPIO_4_2 */
- 0x4033 /* MX28_PAD_ENET0_RXD0__GPIO_4_3 */
- 0x4043 /* MX28_PAD_ENET0_RXD1__GPIO_4_4 */
- 0x4063 /* MX28_PAD_ENET0_TX_EN__GPIO_4_6 */
- 0x4073 /* MX28_PAD_ENET0_TXD0__GPIO_4_7 */
- 0x4083 /* MX28_PAD_ENET0_TXD1__GPIO_4_8 */
- 0x4103 /* MX28_PAD_ENET_CLK__GPIO_4_16 */
+ MX28_PAD_ENET0_MDC__GPIO_4_0
+ MX28_PAD_ENET0_MDIO__GPIO_4_1
+ MX28_PAD_ENET0_RX_EN__GPIO_4_2
+ MX28_PAD_ENET0_RXD0__GPIO_4_3
+ MX28_PAD_ENET0_RXD1__GPIO_4_4
+ MX28_PAD_ENET0_TX_EN__GPIO_4_6
+ MX28_PAD_ENET0_TXD0__GPIO_4_7
+ MX28_PAD_ENET0_TXD1__GPIO_4_8
+ MX28_PAD_ENET_CLK__GPIO_4_16
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -551,7 +552,7 @@
pca9554_pins: pca9554-pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
+ MX28_PAD_PWM3__GPIO_3_28
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -561,7 +562,7 @@
tsc2007_pins: tsc2007-pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3143 /* MX28_PAD_SAIF0_MCLK__GPIO_3_20 - TSC2007 IRQ */
+ MX28_PAD_SAIF0_MCLK__GPIO_3_20 /* TSC2007 IRQ */
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index f941648..e459d63 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -9,7 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
+#include <dt-bindings/pinctrl/mx28.h>
/ {
interrupt-parent = <&icoll>;
@@ -207,8 +208,8 @@
duart_pins_a: duart@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3102 /* MX28_PAD_PWM0__DUART_RX */
- 0x3112 /* MX28_PAD_PWM1__DUART_TX */
+ MX28_PAD_PWM0__DUART_RX
+ MX28_PAD_PWM1__DUART_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -218,8 +219,8 @@
duart_pins_b: duart@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */
- 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */
+ MX28_PAD_AUART0_CTS__DUART_RX
+ MX28_PAD_AUART0_RTS__DUART_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -229,10 +230,10 @@
duart_4pins_a: duart-4pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */
- 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */
- 0x3002 /* MX28_PAD_AUART0_RX__DUART_CTS */
- 0x3012 /* MX28_PAD_AUART0_TX__DUART_RTS */
+ MX28_PAD_AUART0_CTS__DUART_RX
+ MX28_PAD_AUART0_RTS__DUART_TX
+ MX28_PAD_AUART0_RX__DUART_CTS
+ MX28_PAD_AUART0_TX__DUART_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -242,21 +243,21 @@
gpmi_pins_a: gpmi-nand@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0000 /* MX28_PAD_GPMI_D00__GPMI_D0 */
- 0x0010 /* MX28_PAD_GPMI_D01__GPMI_D1 */
- 0x0020 /* MX28_PAD_GPMI_D02__GPMI_D2 */
- 0x0030 /* MX28_PAD_GPMI_D03__GPMI_D3 */
- 0x0040 /* MX28_PAD_GPMI_D04__GPMI_D4 */
- 0x0050 /* MX28_PAD_GPMI_D05__GPMI_D5 */
- 0x0060 /* MX28_PAD_GPMI_D06__GPMI_D6 */
- 0x0070 /* MX28_PAD_GPMI_D07__GPMI_D7 */
- 0x0100 /* MX28_PAD_GPMI_CE0N__GPMI_CE0N */
- 0x0140 /* MX28_PAD_GPMI_RDY0__GPMI_READY0 */
- 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */
- 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */
- 0x01a0 /* MX28_PAD_GPMI_ALE__GPMI_ALE */
- 0x01b0 /* MX28_PAD_GPMI_CLE__GPMI_CLE */
- 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */
+ MX28_PAD_GPMI_D00__GPMI_D0
+ MX28_PAD_GPMI_D01__GPMI_D1
+ MX28_PAD_GPMI_D02__GPMI_D2
+ MX28_PAD_GPMI_D03__GPMI_D3
+ MX28_PAD_GPMI_D04__GPMI_D4
+ MX28_PAD_GPMI_D05__GPMI_D5
+ MX28_PAD_GPMI_D06__GPMI_D6
+ MX28_PAD_GPMI_D07__GPMI_D7
+ MX28_PAD_GPMI_CE0N__GPMI_CE0N
+ MX28_PAD_GPMI_RDY0__GPMI_READY0
+ MX28_PAD_GPMI_RDN__GPMI_RDN
+ MX28_PAD_GPMI_WRN__GPMI_WRN
+ MX28_PAD_GPMI_ALE__GPMI_ALE
+ MX28_PAD_GPMI_CLE__GPMI_CLE
+ MX28_PAD_GPMI_RESETN__GPMI_RESETN
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -265,9 +266,9 @@
gpmi_status_cfg: gpmi-status-cfg {
fsl,pinmux-ids = <
- 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */
- 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */
- 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */
+ MX28_PAD_GPMI_RDN__GPMI_RDN
+ MX28_PAD_GPMI_WRN__GPMI_WRN
+ MX28_PAD_GPMI_RESETN__GPMI_RESETN
>;
fsl,drive-strength = <2>;
};
@@ -275,10 +276,10 @@
auart0_pins_a: auart0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */
- 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */
- 0x3020 /* MX28_PAD_AUART0_CTS__AUART0_CTS */
- 0x3030 /* MX28_PAD_AUART0_RTS__AUART0_RTS */
+ MX28_PAD_AUART0_RX__AUART0_RX
+ MX28_PAD_AUART0_TX__AUART0_TX
+ MX28_PAD_AUART0_CTS__AUART0_CTS
+ MX28_PAD_AUART0_RTS__AUART0_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -288,8 +289,8 @@
auart0_2pins_a: auart0-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */
- 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */
+ MX28_PAD_AUART0_RX__AUART0_RX
+ MX28_PAD_AUART0_TX__AUART0_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -299,10 +300,10 @@
auart1_pins_a: auart1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */
- 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */
- 0x3060 /* MX28_PAD_AUART1_CTS__AUART1_CTS */
- 0x3070 /* MX28_PAD_AUART1_RTS__AUART1_RTS */
+ MX28_PAD_AUART1_RX__AUART1_RX
+ MX28_PAD_AUART1_TX__AUART1_TX
+ MX28_PAD_AUART1_CTS__AUART1_CTS
+ MX28_PAD_AUART1_RTS__AUART1_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -312,8 +313,8 @@
auart1_2pins_a: auart1-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */
- 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */
+ MX28_PAD_AUART1_RX__AUART1_RX
+ MX28_PAD_AUART1_TX__AUART1_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -323,8 +324,8 @@
auart2_2pins_a: auart2-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2101 /* MX28_PAD_SSP2_SCK__AUART2_RX */
- 0x2111 /* MX28_PAD_SSP2_MOSI__AUART2_TX */
+ MX28_PAD_SSP2_SCK__AUART2_RX
+ MX28_PAD_SSP2_MOSI__AUART2_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -334,8 +335,8 @@
auart2_2pins_b: auart2-2pins@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3080 /* MX28_PAD_AUART2_RX__AUART2_RX */
- 0x3090 /* MX28_PAD_AUART2_TX__AUART2_TX */
+ MX28_PAD_AUART2_RX__AUART2_RX
+ MX28_PAD_AUART2_TX__AUART2_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -345,10 +346,10 @@
auart3_pins_a: auart3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */
- 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */
- 0x30e0 /* MX28_PAD_AUART3_CTS__AUART3_CTS */
- 0x30f0 /* MX28_PAD_AUART3_RTS__AUART3_RTS */
+ MX28_PAD_AUART3_RX__AUART3_RX
+ MX28_PAD_AUART3_TX__AUART3_TX
+ MX28_PAD_AUART3_CTS__AUART3_CTS
+ MX28_PAD_AUART3_RTS__AUART3_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -358,8 +359,8 @@
auart3_2pins_a: auart3-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2121 /* MX28_PAD_SSP2_MISO__AUART3_RX */
- 0x2131 /* MX28_PAD_SSP2_SS0__AUART3_TX */
+ MX28_PAD_SSP2_MISO__AUART3_RX
+ MX28_PAD_SSP2_SS0__AUART3_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -369,8 +370,8 @@
auart3_2pins_b: auart3-2pins@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */
- 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */
+ MX28_PAD_AUART3_RX__AUART3_RX
+ MX28_PAD_AUART3_TX__AUART3_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -380,8 +381,8 @@
auart4_2pins_a: auart4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2181 /* MX28_PAD_SSP3_SCK__AUART4_TX */
- 0x2191 /* MX28_PAD_SSP3_MOSI__AUART4_RX */
+ MX28_PAD_SSP3_SCK__AUART4_TX
+ MX28_PAD_SSP3_MOSI__AUART4_RX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -391,15 +392,15 @@
mac0_pins_a: mac0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x4000 /* MX28_PAD_ENET0_MDC__ENET0_MDC */
- 0x4010 /* MX28_PAD_ENET0_MDIO__ENET0_MDIO */
- 0x4020 /* MX28_PAD_ENET0_RX_EN__ENET0_RX_EN */
- 0x4030 /* MX28_PAD_ENET0_RXD0__ENET0_RXD0 */
- 0x4040 /* MX28_PAD_ENET0_RXD1__ENET0_RXD1 */
- 0x4060 /* MX28_PAD_ENET0_TX_EN__ENET0_TX_EN */
- 0x4070 /* MX28_PAD_ENET0_TXD0__ENET0_TXD0 */
- 0x4080 /* MX28_PAD_ENET0_TXD1__ENET0_TXD1 */
- 0x4100 /* MX28_PAD_ENET_CLK__CLKCTRL_ENET */
+ MX28_PAD_ENET0_MDC__ENET0_MDC
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -409,12 +410,12 @@
mac1_pins_a: mac1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x40f1 /* MX28_PAD_ENET0_CRS__ENET1_RX_EN */
- 0x4091 /* MX28_PAD_ENET0_RXD2__ENET1_RXD0 */
- 0x40a1 /* MX28_PAD_ENET0_RXD3__ENET1_RXD1 */
- 0x40e1 /* MX28_PAD_ENET0_COL__ENET1_TX_EN */
- 0x40b1 /* MX28_PAD_ENET0_TXD2__ENET1_TXD0 */
- 0x40c1 /* MX28_PAD_ENET0_TXD3__ENET1_TXD1 */
+ MX28_PAD_ENET0_CRS__ENET1_RX_EN
+ MX28_PAD_ENET0_RXD2__ENET1_RXD0
+ MX28_PAD_ENET0_RXD3__ENET1_RXD1
+ MX28_PAD_ENET0_COL__ENET1_TX_EN
+ MX28_PAD_ENET0_TXD2__ENET1_TXD0
+ MX28_PAD_ENET0_TXD3__ENET1_TXD1
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -424,17 +425,17 @@
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */
- 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */
- 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */
- 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */
- 0x2040 /* MX28_PAD_SSP0_DATA4__SSP0_D4 */
- 0x2050 /* MX28_PAD_SSP0_DATA5__SSP0_D5 */
- 0x2060 /* MX28_PAD_SSP0_DATA6__SSP0_D6 */
- 0x2070 /* MX28_PAD_SSP0_DATA7__SSP0_D7 */
- 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_DATA0__SSP0_D0
+ MX28_PAD_SSP0_DATA1__SSP0_D1
+ MX28_PAD_SSP0_DATA2__SSP0_D2
+ MX28_PAD_SSP0_DATA3__SSP0_D3
+ MX28_PAD_SSP0_DATA4__SSP0_D4
+ MX28_PAD_SSP0_DATA5__SSP0_D5
+ MX28_PAD_SSP0_DATA6__SSP0_D6
+ MX28_PAD_SSP0_DATA7__SSP0_D7
+ MX28_PAD_SSP0_CMD__SSP0_CMD
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -444,13 +445,13 @@
mmc0_4bit_pins_a: mmc0-4bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */
- 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */
- 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */
- 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */
- 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_DATA0__SSP0_D0
+ MX28_PAD_SSP0_DATA1__SSP0_D1
+ MX28_PAD_SSP0_DATA2__SSP0_D2
+ MX28_PAD_SSP0_DATA3__SSP0_D3
+ MX28_PAD_SSP0_CMD__SSP0_CMD
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -459,14 +460,14 @@
mmc0_cd_cfg: mmc0-cd-cfg {
fsl,pinmux-ids = <
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
>;
fsl,pull-up = <0>;
};
mmc0_sck_cfg: mmc0-sck-cfg {
fsl,pinmux-ids = <
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
fsl,drive-strength = <2>;
fsl,pull-up = <0>;
@@ -475,8 +476,8 @@
i2c0_pins_a: i2c0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3180 /* MX28_PAD_I2C0_SCL__I2C0_SCL */
- 0x3190 /* MX28_PAD_I2C0_SDA__I2C0_SDA */
+ MX28_PAD_I2C0_SCL__I2C0_SCL
+ MX28_PAD_I2C0_SDA__I2C0_SDA
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -486,8 +487,8 @@
i2c0_pins_b: i2c0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3001 /* MX28_PAD_AUART0_RX__I2C0_SCL */
- 0x3011 /* MX28_PAD_AUART0_TX__I2C0_SDA */
+ MX28_PAD_AUART0_RX__I2C0_SCL
+ MX28_PAD_AUART0_TX__I2C0_SDA
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -497,8 +498,8 @@
i2c1_pins_a: i2c1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3101 /* MX28_PAD_PWM0__I2C1_SCL */
- 0x3111 /* MX28_PAD_PWM1__I2C1_SDA */
+ MX28_PAD_PWM0__I2C1_SCL
+ MX28_PAD_PWM1__I2C1_SDA
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -508,10 +509,10 @@
saif0_pins_a: saif0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3140 /* MX28_PAD_SAIF0_MCLK__SAIF0_MCLK */
- 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */
- 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */
- 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */
+ MX28_PAD_SAIF0_MCLK__SAIF0_MCLK
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -521,9 +522,9 @@
saif0_pins_b: saif0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */
- 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */
- 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -533,7 +534,7 @@
saif1_pins_a: saif1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31a0 /* MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 */
+ MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -543,7 +544,7 @@
pwm0_pins_a: pwm0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3100 /* MX28_PAD_PWM0__PWM_0 */
+ MX28_PAD_PWM0__PWM_0
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -553,7 +554,7 @@
pwm2_pins_a: pwm2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3120 /* MX28_PAD_PWM2__PWM_2 */
+ MX28_PAD_PWM2__PWM_2
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -563,7 +564,7 @@
pwm3_pins_a: pwm3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31c0 /* MX28_PAD_PWM3__PWM_3 */
+ MX28_PAD_PWM3__PWM_3
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -573,7 +574,7 @@
pwm3_pins_b: pwm3@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3141 /* MX28_PAD_SAIF0_MCLK__PWM3 */
+ MX28_PAD_SAIF0_MCLK__PWM_3
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -583,7 +584,7 @@
pwm4_pins_a: pwm4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31d0 /* MX28_PAD_PWM4__PWM_4 */
+ MX28_PAD_PWM4__PWM_4
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -593,30 +594,30 @@
lcdif_24bit_pins_a: lcdif-24bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
- 0x1120 /* MX28_PAD_LCD_D18__LCD_D18 */
- 0x1130 /* MX28_PAD_LCD_D19__LCD_D19 */
- 0x1140 /* MX28_PAD_LCD_D20__LCD_D20 */
- 0x1150 /* MX28_PAD_LCD_D21__LCD_D21 */
- 0x1160 /* MX28_PAD_LCD_D22__LCD_D22 */
- 0x1170 /* MX28_PAD_LCD_D23__LCD_D23 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ MX28_PAD_LCD_D18__LCD_D18
+ MX28_PAD_LCD_D19__LCD_D19
+ MX28_PAD_LCD_D20__LCD_D20
+ MX28_PAD_LCD_D21__LCD_D21
+ MX28_PAD_LCD_D22__LCD_D22
+ MX28_PAD_LCD_D23__LCD_D23
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -626,22 +627,22 @@
lcdif_16bit_pins_a: lcdif-16bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -651,10 +652,10 @@
lcdif_sync_pins_a: lcdif-sync@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -664,8 +665,8 @@
can0_pins_a: can0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0161 /* MX28_PAD_GPMI_RDY2__CAN0_TX */
- 0x0171 /* MX28_PAD_GPMI_RDY3__CAN0_RX */
+ MX28_PAD_GPMI_RDY2__CAN0_TX
+ MX28_PAD_GPMI_RDY3__CAN0_RX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -675,8 +676,8 @@
can1_pins_a: can1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0121 /* MX28_PAD_GPMI_CE2N__CAN1_TX */
- 0x0131 /* MX28_PAD_GPMI_CE3N__CAN1_RX */
+ MX28_PAD_GPMI_CE2N__CAN1_TX
+ MX28_PAD_GPMI_CE3N__CAN1_RX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -686,10 +687,10 @@
spi2_pins_a: spi2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2100 /* MX28_PAD_SSP2_SCK__SSP2_SCK */
- 0x2110 /* MX28_PAD_SSP2_MOSI__SSP2_CMD */
- 0x2120 /* MX28_PAD_SSP2_MISO__SSP2_D0 */
- 0x2130 /* MX28_PAD_SSP2_SS0__SSP2_D3 */
+ MX28_PAD_SSP2_SCK__SSP2_SCK
+ MX28_PAD_SSP2_MOSI__SSP2_CMD
+ MX28_PAD_SSP2_MISO__SSP2_D0
+ MX28_PAD_SSP2_SS0__SSP2_D3
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -699,12 +700,12 @@
spi3_pins_a: spi3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3082 /* MX28_PAD_AUART2_RX__SSP3_D4 */
- 0x3092 /* MX28_PAD_AUART2_TX__SSP3_D5 */
- 0x2180 /* MX28_PAD_SSP3_SCK__SSP3_SCK */
- 0x2190 /* MX28_PAD_SSP3_MOSI__SSP3_CMD */
- 0x21A0 /* MX28_PAD_SSP3_MISO__SSP3_D0 */
- 0x21B0 /* MX28_PAD_SSP3_SS0__SSP3_D3 */
+ MX28_PAD_AUART2_RX__SSP3_D4
+ MX28_PAD_AUART2_TX__SSP3_D5
+ MX28_PAD_SSP3_SCK__SSP3_SCK
+ MX28_PAD_SSP3_MOSI__SSP3_CMD
+ MX28_PAD_SSP3_MISO__SSP3_D0
+ MX28_PAD_SSP3_SS0__SSP3_D3
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -714,7 +715,7 @@
usbphy0_pins_a: usbphy0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2152 /* MX28_PAD_SSP2_SS2__USB0_OVERCURRENT */
+ MX28_PAD_SSP2_SS2__USB0_OVERCURRENT
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -724,7 +725,7 @@
usbphy0_pins_b: usbphy0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3061 /* MX28_PAD_AUART1_CTS__USB0_OVERCURRENT */
+ MX28_PAD_AUART1_CTS__USB0_OVERCURRENT
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -734,8 +735,8 @@
usbphy0_pins_c: usbphy0@2 {
reg = <2>;
fsl,pinmux-ids = <
- 0x0123 /* MX28_PAD_GPMI_CE2N__GPIO_0_18 - USBOTG_VBUSEN */
- 0x0133 /* MX28_PAD_GPMI_CE3N__GPIO_0_19 - USBOTH_OC */
+ MX28_PAD_GPMI_CE2N__GPIO_0_18 /* USBOTG_VBUSEN */
+ MX28_PAD_GPMI_CE3N__GPIO_0_19 /* USBOTH_OC */
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -745,7 +746,7 @@
usbphy1_pins_a: usbphy1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2142 /* MX28_PAD_SSP2_SS1__USB1_OVERCURRENT */
+ MX28_PAD_SSP2_SS1__USB1_OVERCURRENT
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -755,8 +756,8 @@
usbphy1_pins_b: usbphy1@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x31b3 /* MX28_PAD_SPDIF__GPIO_3_27 - USBH_VBUSEN */
- 0x4143 /* MX28_PAD_JTAG_RTCK__GPIO_4_20 - USBH_OC */
+ MX28_PAD_SPDIF__GPIO_3_27 /* USBH_VBUSEN */
+ MX28_PAD_JTAG_RTCK__GPIO_4_20 /* USBH_OC */
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
--
1.7.2.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
