Hi, Pekon 2013/8/26 Gupta, Pekon <pekon@xxxxxx>: >> >> Signed-off-by: wangyuhang <wangyuhang2014@xxxxxxxxx> >> --- >> Documentation/devicetree/bindings/spi/spi-bus.txt | 14 ++++++++++++++ >> 1 file changed, 14 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt >> b/Documentation/devicetree/bindings/spi/spi-bus.txt >> index 296015e..145ba96 100644 >> --- a/Documentation/devicetree/bindings/spi/spi-bus.txt >> +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt >> @@ -55,6 +55,20 @@ contain the following properties. >> chip select active high >> - spi-3wire - (optional) Empty property indicating device requires >> 3-wire mode. >> +- spi-tx-nbits - (optional) Number of bits used for MOSI(writting) >> +- spi-rx-nbits - (optional) Number of bits used for MISO(reading) >> + >> +So if for example the slave has 4 wires for writting and 2 wires for reading, >> +and the spi-tx/rx-nbits property should be set as follows: >> + >> +spi-tx-nbits = <4>; >> +spi-rx-nbits = <2>; > > [Pekon]: there is a problem here... > spi-tx-nbit = <4> suggests that SPI device support QUAD writes, but it does > not indicate whether DUAL writes are supported by device or not. > So, In my view having either of the following implementation could help > in specifying capabilities independently and clearly. > *Implementation-1 Boolean* > spi-tx-quad = <true | false> > spi-tx-dual = <true | false> > spi-tx-single = <true | false> > Same way for Rx.. > spi-rx-quad = <true | false> > spi-rx-dual = <true | false> > spi-rx-single = <true | false> > > *Implementation-2 Multi-option* > spi-quad = <tx-only | rx-only | duplex> > spi-dual = <tx-only | rx-only | duplex> > spi-single = <tx-only | rx-only | full-duplex | half-duplex> > Not exactly, spi-tx-nbit = <4> suggests that SPI device will use QUAD writes, not support QUAD writes. There is no need to set what mode slave supports, user just set the certain mode slave will work in. >> + >> +Now the value that spi-tx-nbits and spi-rx-nbits can receive is only >> +1(single), 2(dual) and 4(quad). If you don't set spi-tx-nbits or spi-rx-nbits, >> +spi_device mode will be set in single(1 wire) as default. Another point, if >> +property:spi-3wire is set, spi-tx/rx-nbits is forbidden to set to <2 or 4>, >> +otherwise, an errro will return. >> > [Pekon]: Also, instead of having separate binding for 'spi-3wire', it can be > moved under as spi-single = <half-duplex>. > Full-duplex = Tx and Rx operate on independent channels and concurrently. > Half-duplex = Tx and Rx use same bi-directional channel for transmission > one by one > Actually, spi-3wire can be regarded as a part of spi-single, but corrected as what you said, there will be some inconvenient. 1,the driver that has already used spi-3wire need a big change. 2,there have to be a complexed check in spi framework if set like: spi-quad = <tx-only | rx-only | duplex> spi-dual = <tx-only | rx-only | duplex> spi-single = <tx-only | rx-only | full-duplex | half-duplex> >> If a gpio chipselect is used for the SPI slave the gpio number will be passed >> via the cs_gpio >> -- >> 1.7.9.5 > > with regards, pekon -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
