On 08/19/2013 05:29 PM, Mark Rutland wrote:
On Mon, Aug 19, 2013 at 02:42:05PM +0100, Tero Kristo wrote:
On 08/13/2013 02:04 PM, Mark Rutland wrote:
On Fri, Aug 02, 2013 at 05:25:24PM +0100, Tero Kristo wrote:
This node adds support for a clock node which allows control to the
clockdomain enable / disable.
Signed-off-by: Tero Kristo <t-kristo@xxxxxx>
---
.../devicetree/bindings/clock/ti/gate.txt | 41 ++++++++
arch/arm/mach-omap2/clock.h | 9 --
drivers/clk/ti/Makefile | 2 +-
drivers/clk/ti/gate.c | 106 ++++++++++++++++++++
include/linux/clk/ti.h | 8 ++
5 files changed, 156 insertions(+), 10 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/ti/gate.txt
create mode 100644 drivers/clk/ti/gate.c
diff --git a/Documentation/devicetree/bindings/clock/ti/gate.txt b/Documentation/devicetree/bindings/clock/ti/gate.txt
new file mode 100644
index 0000000..620a73d
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/gate.txt
@@ -0,0 +1,41 @@
+Binding for Texas Instruments gate clock.
+
+This binding uses the common clock binding[1]. This clock is
+quite much similar to the basic gate-clock [2], however,
+it supports a number of additional features. If no register
+is provided for this clock, the code assumes that a clockdomain
+will be controlled instead and the corresponding hw-ops for
+that is used.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/clock/gate-clock.txt
+
+Required properties:
+- compatible : shall be "ti,gate-clock"
+- #clock-cells : from common clock binding; shall be set to 0
+- clocks : link to phandle of parent clock
+
+Optional properties:
+- reg : base address for register controlling adjustable gate
Optional? That's odd. If I have a clock with registers, but don't
specify the register, will it still work? i.e. are registerless clocks
really compatible with clocks with registers?.
I think I implemented this in somewhat confusing manner. This could be
split to:
ti,gate-clock:
requires reg and ti,enable-bit info
ti,clkdm-clock:
requires ti,clkdm-name
clkdm clock is kind of a master clock for clockdomain, the clock is
provided always if the clockdomain is active.
Ok.
+- ti,enable-bit : bit shift for programming the clock gate
Why is this needed? Does the hardware vary wildly, or are several clocks
sharing the same register(s)?
Yea, same register is shared.
Ok. Are those gate clocks are part of a larger "gate clocks" block, with
the register that controls them? or are they really independent? Does
the register control other items too?
Not really. Typically they only have the clockdomain in common, and the
individual clocks are mostly controlled independently from each other.
For example on omap3 we have following register:
CM_FCLKEN_PER
Physical Address 0x4800 5000
BIT31:19 RESERVED Write 0s for future compatibility. Read returns 0.
BIT18 EN_UART4 UART4 functional clock control.
BIT17 EN_GPIO6 GPIO6 functional clock control.
BIT16 EN_GPIO5 GPIO5 functional clock control.
BIT15 EN_GPIO4 GPIO4 functional clock control.
BIT14 EN_GPIO3 GPIO3 functional clock control.
BIT13 EN_GPIO2 GPIO2 functional clock control.
BIT12 EN_WDT3 WDT3 functional clock control.
BIT11 EN_UART3 Type UART3 functional clock control.
BIT10 EN_GPT9 GPTIMER 9 functional clock control.
BIT9 EN_GPT8 GPTIMER 8 functional clock control.
BIT8 EN_GPT7 GPTIMER 7 functional clock control.
BIT7 EN_GPT6 GPTIMER 6 functional clock control.
BIT6 EN_GPT5 GPTIMER 5 functional clock control.
BIT5 EN_GPT4 GPTIMER 4 functional clock control.
BIT4 EN_GPT3GPTIMER 3 functional clock control.
BIT3 EN_GPT2 GPTIMER 2 functional clock control.
BIT2 EN_MCBSP4 McBSP 4 functional clock control.
BIT1 EN_MCBSP3 McBSP3 functional clock control.
BIT0 EN_MCBSP2 McBSP 2 functional clock control.
So multiple drivers will be using this register for example.
If they were part of some bigger unit, it might be possible to have a
binding like the following (though maybe not):
gate_clks: gate_clks {
compatible = "ti,gate-clocks-block";
reg = <0x4003a000 0x1000>;
#clock-cells = <1>;
/*
* has 4 gate clocks at bit shifts 0,1,2,3,
* corresponding to input clocks 0,1,2,3
*/
clocks = <&clk1 0 23>,
<&clk1 0 4>,
<&clk3 2>,
<&clk3 5>;
};
device {
compatible = "vendor,some-device";
clocks = <&gate_clks 1>; /* gate clock with bitshift 1*/
};
+- ti,dss-clk : use DSS hardware OPS for the clock
+- ti,am35xx-clk : use AM35xx hardware OPS for the clock
Those last two sounds like the kind of thing that should be derived from
the compatible string (e.g. ti,am35xx-gate-clock).
Hmm yea, I think I can change this and add some sub-types.
+- ti,clkdm-name : clockdomain to control this gate
As previously mentioned, I'm not a fan of this property. It would make
more sense to describe the domain and have an explicit link to it
(either nodes being children of the domain or having a phandle).
Same comments as with patch #2.
Same reply as to patch #2 :)
I'll think of a proper reply there. :)
-Tero
[...]
+void __init of_omap_gate_clk_setup(struct device_node *node)
+{
+ struct clk *clk;
+ struct clk_init_data init = { 0 };
+ struct clk_hw_omap *clk_hw;
+ const char *clk_name = node->name;
+ int num_parents;
+ const char **parent_names = NULL;
+ int i;
+ u32 val;
+
+ clk_hw = kzalloc(sizeof(*clk_hw), GFP_KERNEL);
+ if (!clk_hw) {
+ pr_err("%s: could not allocate clk_hw_omap\n", __func__);
+ return;
+ }
+
+ clk_hw->hw.init = &init;
+
+ of_property_read_string(node, "clock-output-names", &clk_name);
+ of_property_read_string(node, "ti,clkdm-name", &clk_hw->clkdm_name);
+
+ init.name = clk_name;
+ init.flags = 0;
+
+ if (of_property_read_u32_index(node, "reg", 0, &val)) {
+ /* No register, clkdm control only */
+ init.ops = &omap_gate_clkdm_clk_ops;
If they're truly compatible, you can just see if you can of_iomap, and
if not, continue. Your reg values might be wider than 32 bits, and usig
of_property_read_u32 to read this feels wrong.
I'll split this to two separate supported types.
+ } else {
+ init.ops = &omap_gate_clk_ops;
+ clk_hw->enable_reg = of_iomap(node, 0);
+ of_property_read_u32(node, "ti,enable-bit", &val);
+ clk_hw->enable_bit = val;
What if of_property_read_u32 failed to read the "ti,enable-bit"
property? One might not be present, it's marked as optional in the
binding description.
I'll make sure this is present in case it is needed.
+
+ clk_hw->ops = &clkhwops_wait;
+
+ if (of_property_read_bool(node, "ti,dss-clk"))
+ clk_hw->ops = &clkhwops_omap3430es2_dss_usbhost_wait;
+
+ if (of_property_read_bool(node, "ti,am35xx-clk"))
+ clk_hw->ops = &clkhwops_am35xx_ipss_module_wait;
I really don't like this. I think this should be done based on the
compatible string.
Yea, will change.
Cheers!
Mark.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html