Re: [PATCHv5 05/31] CLK: TI: add support for OMAP gate clock

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 08/13/2013 02:04 PM, Mark Rutland wrote:
On Fri, Aug 02, 2013 at 05:25:24PM +0100, Tero Kristo wrote:
This node adds support for a clock node which allows control to the
clockdomain enable / disable.

Signed-off-by: Tero Kristo <t-kristo@xxxxxx>
---
  .../devicetree/bindings/clock/ti/gate.txt          |   41 ++++++++
  arch/arm/mach-omap2/clock.h                        |    9 --
  drivers/clk/ti/Makefile                            |    2 +-
  drivers/clk/ti/gate.c                              |  106 ++++++++++++++++++++
  include/linux/clk/ti.h                             |    8 ++
  5 files changed, 156 insertions(+), 10 deletions(-)
  create mode 100644 Documentation/devicetree/bindings/clock/ti/gate.txt
  create mode 100644 drivers/clk/ti/gate.c

diff --git a/Documentation/devicetree/bindings/clock/ti/gate.txt b/Documentation/devicetree/bindings/clock/ti/gate.txt
new file mode 100644
index 0000000..620a73d
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/gate.txt
@@ -0,0 +1,41 @@
+Binding for Texas Instruments gate clock.
+
+This binding uses the common clock binding[1]. This clock is
+quite much similar to the basic gate-clock [2], however,
+it supports a number of additional features. If no register
+is provided for this clock, the code assumes that a clockdomain
+will be controlled instead and the corresponding hw-ops for
+that is used.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/clock/gate-clock.txt
+
+Required properties:
+- compatible : shall be "ti,gate-clock"
+- #clock-cells : from common clock binding; shall be set to 0
+- clocks : link to phandle of parent clock
+
+Optional properties:
+- reg : base address for register controlling adjustable gate

Optional? That's odd. If I have a clock with registers, but don't
specify the register, will it still work? i.e. are registerless clocks
really compatible with clocks with registers?.

I think I implemented this in somewhat confusing manner. This could be split to:

ti,gate-clock:
  requires reg and ti,enable-bit info
ti,clkdm-clock:
  requires ti,clkdm-name

clkdm clock is kind of a master clock for clockdomain, the clock is provided always if the clockdomain is active.


+- ti,enable-bit : bit shift for programming the clock gate

Why is this needed? Does the hardware vary wildly, or are several clocks
sharing the same register(s)?

Yea, same register is shared.


+- ti,dss-clk : use DSS hardware OPS for the clock
+- ti,am35xx-clk : use AM35xx hardware OPS for the clock

Those last two sounds like the kind of thing that should be derived from
the compatible string (e.g. ti,am35xx-gate-clock).

Hmm yea, I think I can change this and add some sub-types.


+- ti,clkdm-name : clockdomain to control this gate

As previously mentioned, I'm not a fan of this property. It would make
more sense to describe the domain and have an explicit link to it
(either nodes being children of the domain or having a phandle).

Same comments as with patch #2.


[...]

+void __init of_omap_gate_clk_setup(struct device_node *node)
+{
+       struct clk *clk;
+       struct clk_init_data init = { 0 };
+       struct clk_hw_omap *clk_hw;
+       const char *clk_name = node->name;
+       int num_parents;
+       const char **parent_names = NULL;
+       int i;
+       u32 val;
+
+       clk_hw = kzalloc(sizeof(*clk_hw), GFP_KERNEL);
+       if (!clk_hw) {
+               pr_err("%s: could not allocate clk_hw_omap\n", __func__);
+               return;
+       }
+
+       clk_hw->hw.init = &init;
+
+       of_property_read_string(node, "clock-output-names", &clk_name);
+       of_property_read_string(node, "ti,clkdm-name", &clk_hw->clkdm_name);
+
+       init.name = clk_name;
+       init.flags = 0;
+
+       if (of_property_read_u32_index(node, "reg", 0, &val)) {
+               /* No register, clkdm control only */
+               init.ops = &omap_gate_clkdm_clk_ops;

If they're truly compatible, you can just see if you can of_iomap, and
if not, continue. Your reg values might be wider than 32 bits, and usig
of_property_read_u32 to read this feels wrong.

I'll split this to two separate supported types.


+       } else {
+               init.ops = &omap_gate_clk_ops;
+               clk_hw->enable_reg = of_iomap(node, 0);
+               of_property_read_u32(node, "ti,enable-bit", &val);
+               clk_hw->enable_bit = val;

What if of_property_read_u32 failed to read the "ti,enable-bit"
property? One might not be present, it's marked as optional in the
binding description.

I'll make sure this is present in case it is needed.


+
+               clk_hw->ops = &clkhwops_wait;
+
+               if (of_property_read_bool(node, "ti,dss-clk"))
+                       clk_hw->ops = &clkhwops_omap3430es2_dss_usbhost_wait;
+
+               if (of_property_read_bool(node, "ti,am35xx-clk"))
+                       clk_hw->ops = &clkhwops_am35xx_ipss_module_wait;

I really don't like this. I think this should be done based on the
compatible string.

Yea, will change.

-Tero

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux