On 11/9/06, isplist@xxxxxxxxxxxx <isplist@xxxxxxxxxxxx> wrote:
> Try removing that interface then starting up pulse. The netmask and
> gateway looks really off compared to eth0. Pulse will add the
> interface and then write back with your ifconfig output.
Ok, stopped pulse;
Nothing to remove on interface, restart pulse;
# ifconfig
eth0 Link encap:Ethernet HWaddr 00:20:94:10:44:A5
inet addr:192.168.1.52 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::220:94ff:fe10:44a5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:218526 errors:0 dropped:0 overruns:0 frame:0
TX packets:44604 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:14276764 (13.6 MiB) TX bytes:4034081 (3.8 MiB)
eth0:1 Link encap:Ethernet HWaddr 00:20:94:10:44:A5
inet addr:192.168.1.150 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
Pulse adds VIP to interface;
# tail -f /var/log/messages
Nov 9 14:51:04 lb52 pulse[3487]: STARTING PULSE AS MASTER
Nov 9 14:51:04 lb52 pulse: pulse startup succeeded
Nov 9 14:51:22 lb52 pulse[3487]: partner dead: activating lvs
Nov 9 14:51:22 lb52 lvs[3494]: starting virtual service HTTP active: 80
Nov 9 14:51:22 lb52 nanny[3498]: starting LVS client monitor for
192.168.1.150:80
Nov 9 14:51:22 lb52 lvs[3494]: create_monitor for HTTP/cweb92 running as pid
3498
Nov 9 14:51:22 lb52 nanny[3499]: starting LVS client monitor for
192.168.1.150:80
Nov 9 14:51:22 lb52 lvs[3494]: create_monitor for HTTP/cweb93 running as pid
3499
Nov 9 14:51:22 lb52 nanny[3500]: starting LVS client monitor for
192.168.1.150:80
Nov 9 14:51:22 lb52 lvs[3494]: create_monitor for HTTP/cweb94 running as pid
3500
Nov 9 14:51:27 lb52 pulse[3501]: gratuitous lvs arps finished
Nov 9 14:51:28 lb52 nanny[3498]: READ to 192.168.1.92:80 timed out
Nov 9 14:51:28 lb52 nanny[3499]: READ to 192.168.1.93:80 timed out
Nov 9 14:51:28 lb52 nanny[3500]: READ to 192.168.1.94:80 timed out
Here's another one that might help:
Your LVS reads:
send = "GET / HTTP/1.0rnrn"
It should be (at least one mine it is):
send = "GET / HTTP/1.0\r\n\r\n"
Could be a copy/paste problem but that might be your problem in
addition to the interface mentioned before.
--
Linux-cluster mailing list
Linux-cluster@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/linux-cluster
