Hi, Yes we tries that, and it's working. That's the way we do it when I refer to removing them manually. Sorry if my first message was not clear enough. My question is, is there a way to remove some config key from some declaration on the orch's spec file or not? Luis Domingues Proton AG ------- Original Message ------- On Tuesday, July 19th, 2022 at 13:47, Redouane Kachach Elhichou <rkachach@xxxxxxxxxx> wrote: > Did you try the *rm *option? both ceph config and ceph config-key support > removing config kyes: > > From: > https://docs.ceph.com/en/quincy/man/8/ceph/#ceph-ceph-administration-tool > > ceph config-key [ rm | exists | get | ls | dump | set ] … > ceph config [ dump | ls | help | get | show | show-with-defaults > | set | rm | log | reset | assimilate-conf | > generate-minimal-conf ] … > > Best, > Redo. > > On Tue, Jul 19, 2022 at 1:24 PM Luis Domingues luis.domingues@xxxxxxxxx > > wrote: > > > Hi, > > > > We are interested in the exact same feature. I was able to test it. > > > > I have a question regarding the removal of some configuration. If I add > > some config, I can see it using ceph config dump. But if I remove it from > > my spec file, it stays on the ceph config db. > > > > Is there a way to remove some configuration from the ceph db? Or do we > > need to do the removal manually? > > > > Best, > > > > Luis Domingues > > Proton AG > > > > ------- Original Message ------- > > On Friday, July 15th, 2022 at 17:06, Redouane Kachach Elhichou < > > rkachach@xxxxxxxxxx> wrote: > > > > > This section could be added to any service spec. cephadm will parse it > > > and > > > apply all the values included in the same. > > > > > > There's no documentation because this wasn't documented so far. I've just > > > created a PR for that purpose: > > > > > > https://github.com/ceph/ceph/pull/46926 > > > > > > Best, > > > Redo. > > > > > > On Fri, Jul 15, 2022 at 4:47 PM Ali Akil ali-akil@xxxxxx wrote: > > > > > > > Where to this add this section exactly. In the osd service > > > > specification > > > > section https://docs.ceph.com/en/latest/cephadm/services/osd/#examples > > > > there is not mention for config. > > > > Also cephadm doesn't seem to apply changes added to ceph.conf. > > > > > > > > Best Regards, > > > > Ali > > > > On 15.07.22 15:21, Redouane Kachach Elhichou wrote: > > > > > > > > Hello Ali, > > > > > > > > You can set configuration by including a config section in our yaml as > > > > following: > > > > > > > > config: > > > > param_1: val_1 > > > > ... > > > > param_N: val_N > > > > > > > > this is equivalent to call the following ceph cmd: > > > > > > > > > ceph config set <service-name> <param> <value> > > > > > > > > Best Regards, > > > > Redo. > > > > > > > > On Fri, Jul 15, 2022 at 2:45 PM Ali Akil ali-akil@xxxxxx wrote: > > > > > > > > > Hallo, > > > > > > > > > > i used to set the configuration for Ceph using the cli aka `ceph config set global osd_deep_scrub_interval <value>`. I would like though to > > > > > store these configuration in my git repository. Is there a way to > > > > > apply > > > > > these configurations as yaml file? > > > > > > > > > > I am using Quincy ceph cluster provisioned by cephadm. > > > > > > > > > > Best Regards, > > > > > Ali Akil > > > > > > > > > > _______________________________________________ > > > > > ceph-users mailing list -- ceph-users@xxxxxxx > > > > > To unsubscribe send an email to ceph-users-leave@xxxxxxx > > > > > > _______________________________________________ > > > ceph-users mailing list -- ceph-users@xxxxxxx > > > To unsubscribe send an email to ceph-users-leave@xxxxxxx > > > _______________________________________________ > > > ceph-users mailing list -- ceph-users@xxxxxxx > > > To unsubscribe send an email to ceph-users-leave@xxxxxxx > > _______________________________________________ > ceph-users mailing list -- ceph-users@xxxxxxx > To unsubscribe send an email to ceph-users-leave@xxxxxxx _______________________________________________ ceph-users mailing list -- ceph-users@xxxxxxx To unsubscribe send an email to ceph-users-leave@xxxxxxx
 |