> Op 15 juli 2016 om 21:19 schreef Will Dennis <willard.dennis@xxxxxxxxx>: > > > Hi all, > > Background: Completely new to Ceph; trying it out on three VMs I have, following install instructions found at http://docs.ceph.com/docs/master/start/quick-ceph-deploy/ <http://docs.ceph.com/docs/master/start/quick-ceph-deploy/> > > I am at the point in the docs where it says to run 'ceph-deploy osd activate’ on the other two nodes from the first node. I try to do so, but get the following error: > > [root@ceph2 ~]# ceph-deploy osd activate ceph3:/dev/sdc ceph3:/dev/sdd ceph3:/dev/sde > [ceph_deploy.conf][DEBUG ] found configuration file at: /root/.cephdeploy.conf > [ceph_deploy.cli][INFO ] Invoked (1.5.25): /bin/ceph-deploy osd activate ceph3:/dev/sdc ceph3:/dev/sdd ceph3:/dev/sde > [ceph_deploy.osd][DEBUG ] Activating cluster ceph disks ceph3:/dev/sdc: ceph3:/dev/sdd: ceph3:/dev/sde: > [ceph3][DEBUG ] connected to host: ceph3 > [ceph3][DEBUG ] detect platform information from remote host > [ceph3][DEBUG ] detect machine type > [ceph_deploy.osd][INFO ] Distro info: CentOS Linux 7.2.1511 Core > [ceph_deploy.osd][DEBUG ] activating host ceph3 disk /dev/sdc > [ceph_deploy.osd][DEBUG ] will use init type: sysvinit > [ceph3][INFO ] Running command: ceph-disk -v activate --mark-init sysvinit --mount /dev/sdc > [ceph3][WARNIN] INFO:ceph-disk:Running command: /sbin/blkid -p -s TYPE -ovalue -- /dev/sdc > [ceph3][WARNIN] ceph-disk: Cannot discover filesystem type: device /dev/sdc: Line is truncated: > [ceph3][ERROR ] RuntimeError: command returned non-zero exit status: 1 > [ceph_deploy][ERROR ] RuntimeError: Failed to execute command: ceph-disk -v activate --mark-init sysvinit --mount /dev/sdc > > In some manual testing, I found that if I ran the listed command, indeed I got no output: > [root@ceph2 ~]# ssh root@ceph4 /sbin/blkid -p -s TYPE -ovalue -- /dev/sdc > [root@ceph2 ~]# > > Then tried taking away the ‘-s TYPE’ and ‘-ovalue' params, I got output as follows: > [root@ceph2 ~]# ssh root@ceph4 /sbin/blkid -p -- /dev/sdc > /dev/sdc: PTTYPE="gpt" > [root@ceph2 ~]# > > So if I modified the original command, but set the ‘-s' param to use “PTTYPE” instead of “TYPE”, I get a valid response: > [root@ceph2 ~]# ssh root@ceph4 /sbin/blkid -p -s PTTYPE -ovalue -- /dev/sdc > gpt > [root@ceph2 ~]# > > Is this a bug in ‘osd activate’ (at least on CentOS 7.2), or is there some way to specify the blkid parameter to use? > Which version of Ceph are you testing with? I see 'will use init type: sysvinit' which is odd, since Ceph version Jewel uses systemd. Wido > Thanks, > Will_______________________________________________ > ceph-users mailing list > ceph-users@xxxxxxxxxxxxxx > http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com _______________________________________________ ceph-users mailing list ceph-users@xxxxxxxxxxxxxx http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
 |