OK... When I hit the wall, Ceph got pretty unusable; I haven't figured out how to restore it to health. So to do as you suggest, I am going to have to scrape everything into the trash and try again (3rd time's the charm, right?) - so let me get started on that. I will pause before I run the big test that can overflow the cache and consult with you on what specific steps you might recommend. -don- -----Original Message----- From: Nick Fisk [mailto:nick@xxxxxxxxxx] Sent: 30 April, 2015 10:58 To: Don Doerner; ceph-users@xxxxxxxxxxxxxx Subject: RE: RHEL7/HAMMER cache tier doesn't flush or evict? Sensitivity: Personal I'm using Inkscope to monitor my cluster and looking at the pool details I saw that mode was set to none. I'm pretty sure there must be a ceph cmd line to get the option state but I couldn't find anything obvious when I was looking for it. > -----Original Message----- > From: ceph-users [mailto:ceph-users-bounces@xxxxxxxxxxxxxx] On Behalf > Of Don Doerner > Sent: 30 April 2015 18:47 > To: Nick Fisk; ceph-users@xxxxxxxxxxxxxx > Subject: Re: RHEL7/HAMMER cache tier doesn't flush or evict? > Sensitivity: Personal > > Hi Nick, > > For brevity, I didn't detail all of the commands I issued. Looking > back through > my command history, I can confirm that I did explicitly set cache-mode > to writeback (and later reset it to forward to try flush-and-evict). Question: > how did you determine that your cache-mode was not writeback? I'll do > that, just to confirm that this is the problem, then reestablish the cache- > mode. > > Thank you very much for your assistance! > > -don- > > -----Original Message----- > From: Nick Fisk [mailto:nick@xxxxxxxxxx] > Sent: 30 April, 2015 10:38 > To: Don Doerner; ceph-users@xxxxxxxxxxxxxx > Subject: RE: RHEL7/HAMMER cache tier doesn't flush or evict? > Sensitivity: Personal > > Hi Don, > > I experienced the same thing a couple of days ago on Hammer. On > investigation the cache mode wasn't set to writeback even though I'm > sure it > accepted the command successfully when I set the pool up. > > Could you reapply the cache mode writeback command and see if that > makes a difference? > > Nick > > > -----Original Message----- > > From: ceph-users [mailto:ceph-users-bounces@xxxxxxxxxxxxxx] On > > Behalf Of Don Doerner > > Sent: 30 April 2015 17:57 > > To: ceph-users@xxxxxxxxxxxxxx > > Subject: RHEL7/HAMMER cache tier doesn't flush or evict? > > Sensitivity: Personal > > > > All, > > > > Synopsis: I can't get cache tiering to work in HAMMER on RHEL7. > > > > Process: > > 1. Fresh install of HAMMER on RHEL7 went well. > > 2. Crush map adapted to provide two "root" level resources a. > > "ctstorage", to use as a cache tier based on very high-performance, > high > > IOPS SSD (intrinsic journal). 2 OSDs. > > b. "ecstorage", to use as an erasure-coded poolbased on > > low-performance, cost effective storage (extrinsic journal). 12 OSDs. > > 3. Established a pool "ctpool", 32 PGs on ctstorage (pool size = > > min_size > = 1). > > Ran a quick RADOS bench test, all worked as expected. Cleaned up. > > 4. Established a pool "ecpool", 256 PGs on ecstorage (5+3 profile). > > Ran a quick RADOS bench test, all worked as expected. Cleaned up. > > 5. Ensured that both pools were empty (i.e., "rados ls" shows no > > objects) 6. Put the cache tier on the erasure coded storage (one > > Bloom hit set, interval 900 seconds), set up the overlay. Used > > defaults for flushing and eviction. No errors. > > 7. Started a 3600-second write test to ecpool. > > > > Objects piled up in ctpool (as expected) - went past the 40% mark > > (as expected), then past the 80% mark (unexpected), then ran into > > the wall (95% full - very unexpected). Using "rados df", I can see > > that the cache > tier is > > full (duh!) but not one single object lives in the ecpool. Nothing > > was > ever > > flushed, nothing was ever evicted. Thought I might be misreading > > that, so > I > > went back to SAR data that I captured during the test: the SSDs were > > the > only > > [ceph] devices that sustained I/O. > > > > I based this experiment on another (much more successful) experiment > > that I performed using GIANT (.1) on RHEL7 a couple of weeks ago > > (wherein I used RAM as a cache tier); that all worked. It seems > > there are at least > three > > possibilities. > > . I forgot a critical step this time around. > > . The steps needed for a cache tier in HAMMER are different than the > > steps needed in GIANT (and different than the documentation online). > > . There is a problem with HAMMER in the area of cache tier. > > > > Has anyone successfully deployed cache-tiering in HAMMER? Did you > > have to do anything unusual? Do you see any steps that I missed? > > > > Regards, > > > > -don- > > > > ________________________________________ > > The information contained in this transmission may be confidential. > > Any disclosure, copying, or further distribution of confidential > > information > is not > > permitted unless such privilege is explicitly granted in writing by > Quantum. > > Quantum reserves the right to have electronic communications, > > including email and attachments, sent across its networks filtered > > through anti > virus > > and spam software programs and retain such messages in order to > > comply with applicable data security and retention requirements. > > Quantum is not responsible for the proper and complete transmission > > of the substance of this communication or for any delay in its receipt. > > > > > _______________________________________________ > ceph-users mailing list > ceph-users@xxxxxxxxxxxxxx > https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.ceph.com_lis > tinfo.cgi_ceph-2Dusers-2Dceph.com&d=BQICAg&c=8S5idjlO_n28Ko3lg6lskTMwn > eSC-WqZ5EBTEEvDlkg&r=DAW8QzIBpV_iBddECxqMq8sRPZPQOBqikPmeCBg26bM&m=aNoZ-EWdwG72G_Y6BINvMTf6VjXHuuxJRqXN2Dqn1k0&s=WGWzgEUz8djDKJe0c62GmYz6OqoATjVpYeMHeLiXT_c&e= _______________________________________________ ceph-users mailing list ceph-users@xxxxxxxxxxxxxx http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
 |