Re: need help on second Ethernet port (eth1) point to point connect

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]



setup IP address as "192.168.xxx.xxx" does NOT work. 
Someone say I need use "crossover" type of cable, but
I don't have.  I put a switch and coneect cable from
each PC and it work fine.

Thanks.


 
--- gnulinux <gnulinux@xxxxxxxxxxx> 說:

> mcclnx mcc wrote:
> > I have two DELL servers with two Ethernet ports in
> it.
> >  Bith servers have CENTOS 4.5 installed.  First
> > Ethernet port connect to public Ethernet line and
> work
> > correctly.  Second Ethernet port I connect
> > point-to-point as private Ethernet (cable direct
> > connect without router or switch).  Private
> Ethernet
> > use IP asddress 1.1.1.1 and 1.1.1.2.
> >
> > I check "ifconfig -a" and both eth0 and eth1 are
> up
> > and active.  when I tried to ping another server
> use
> > second port (private) and no response.  Does
> anything
> > I configure wrong?
> >
> > Thanks.
> >
> > ========   info   ===  
> >
> >  %ifconfig -a
> > eth0      Link encap:Ethernet  HWaddr
> > 00:08:74:EA:54:64  
> >           inet addr:172.29.86.15 
> Bcast:172.29.85.255 
> > Mask:255.255.255.0
> >           inet6 addr: fe80::208:74ff:feea:5464/64
> > Scope:Link
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500
> 
> > Metric:1
> >           RX packets:471 errors:0 dropped:0
> overruns:0
> > frame:0
> >           TX packets:91 errors:0 dropped:0
> overruns:0
> > carrier:0
> >           collisions:0 txqueuelen:0 
> >           RX bytes:65669 (64.1 KiB)  TX
> bytes:11847
> > (11.5 KiB)
> >
> > eth1      Link encap:Ethernet  HWaddr
> > 00:0E:2E:C8:B9:80  
> >           inet addr:1.1.1.1  Bcast:1.1.1.255 
> > Mask:255.255.255.0
> >           UP BROADCAST MULTICAST  MTU:1500 
> Metric:1
> >           RX packets:0 errors:0 dropped:0
> overruns:0
> > frame:0
> >           TX packets:0 errors:0 dropped:0
> overruns:0
> > carrier:0
> >           collisions:0 txqueuelen:1000 
> >           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
> >           Interrupt:18 Base address:0x4c00 
> >
> > %ping 1.1.1.2
> > PING 1.1.1.2 (1.1.1.2) 56(84) bytes of data.
> > >From 1.1.1.1 icmp_seq=1 Destination Host
> Unreachable
> > >From 1.1.1.1 icmp_seq=2 Destination Host
> Unreachable
> > >From 1.1.1.1 icmp_seq=3 Destination Host
> Unreachable
> >
> > --- 1.1.1.2 ping statistics ---
> > 4 packets transmitted, 0 received, +3 errors, 100%
> > packet loss, time 3015ms
> > , pipe 3
> >
> >
> > %telnet 1.1.1.2
> > Trying 1.1.1.2...
> > telnet: connect to address 1.1.1.2: No route to
> host
> >   
> Try a private network IP 192.168.xxx.xxx? Right
> ether cable, straight?
> _______________________________________________
> CentOS mailing list
> CentOS@xxxxxxxxxx
> http://lists.centos.org/mailman/listinfo/centos
> 



      ____________________________________________________________________________________
設定安全圖章,保護您的 Yahoo!奇摩帳號不被駭客盜用!
http://tw.info.yahoo.com/seal/index.html
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos

[Index of Archives]     [CentOS]     [CentOS Announce]     [CentOS Development]     [CentOS ARM Devel]     [CentOS Docs]     [CentOS Virtualization]     [Carrier Grade Linux]     [Linux Media]     [Asterisk]     [DCCP]     [Netdev]     [Xorg]     [Linux USB]
  Powered by Linux