Re: Trouble with kernel-3.10.0-1160.80.1.el7.x86_64

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]



On the other hand --- I just upgraded one of my CentOS7 systems to 3.10.0-1160.80.1 today. With that kernel it will not run any KVM guest. The system hangs - HARD - within one or two seconds of issuing the "virsh start ..." command. It hangs so hard that a power-off restart using the back panel switch is required. It does not log any error I can find, nor display any message about a kernel panic.

Rebooting with 3.10.0-1160.76.1 works fine.

The system is an older SuperMicro mainboard with a Q9400 processor.

===============
Bill Gee

On 11/16/22 12:38, Chris Schanzle via CentOS wrote:
On 11/15/22 7:50 PM, Petko Alov wrote:

On 2022-11-08 15:49, Orion Poplawski wrote:

    On 11/8/22 13:12, Simon Matter wrote:

            Is anyone else experiencing trouble with
            kernel-3.10.0-1160.80.1.el7.x86_64?

            I'm seeing a kernel panics in the kvm module on one of our VM hosts with

            it.

            I did notice a new libvirt update as well, but it seems to work fine with

            the
            older kernel (.76.1).

        Where did you get the .80.1 kernel from? I'm a bit confused because I can

        only see .76.1 on my systems.

        Simon

    I'm actually running Scientific Linux, which seems to be a little ahead here. Probably not related, but vmlinuz-4.18.0-372.32.1.el8_6.x86_64 (AlmaLinux 8.6) had a kernel panic on a Intel Xeon E5504 processor, but works fine on Xeon E56XX processors (5620 specifically in our tests). * Believe from kernel version, the original email is for Centos 7, possible the same change that went into the EL8 kernel went also to EL7 Triggered right after I used virsh start to start the vm. (Caused Black Screen, and reboot. Found this in the crashed kernel logs on /var/crash) Works fine on vmlinuz-4.18.0-372.26.1.el8_6.x86_64 and vmlinuz-4.18.0-372.16.1.el8_6.x86_64

In fact, related - on our systems attempt to start qemu-kvm VM under kernel-3.10.0-1160.80.1.el7.x86_64 freezes any of 5 workstations with dual E5507 (all worked OK under kernel-3.10.0-1160.76.1.el7.x86_64 and any previous version). The workstations with E5-2609, E5-2650 or E5-2630 are not affected - all of them run qemu-kvm VM under kernel-3.10.0-1160.80.1.el7.x86_64 without problems.


Thankfully, no problems with 2x Xeon E5-2667 v2 and CentOS 7.9 kernel 3.10.0-1160.80.1.el7.x86_64.

_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
https://lists.centos.org/mailman/listinfo/centos
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
https://lists.centos.org/mailman/listinfo/centos




[Index of Archives]     [CentOS]     [CentOS Announce]     [CentOS Development]     [CentOS ARM Devel]     [CentOS Docs]     [CentOS Virtualization]     [Carrier Grade Linux]     [Linux Media]     [Asterisk]     [DCCP]     [Netdev]     [Xorg]     [Linux USB]


  Powered by Linux