Re: Errors on an SSD drive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]



Robert Moskowitz wrote:


On 08/09/2017 01:48 PM, hw wrote:
Robert Moskowitz wrote:
I am building a new system using an Kingston 240GB SSD drive I pulled from my notebook (when I had to upgrade to a 500GB SSD drive).  Centos install went fine and ran for a couple days then got errors on the console.  Here is an example:

[168176.995064] sd 0:0:0:0: [sda] tag#14 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[168177.004050] sd 0:0:0:0: [sda] tag#14 CDB: Read(10) 28 00 01 04 68 b0 00 00 08 00
[168177.011615] blk_update_request: I/O error, dev sda, sector 17066160
[168487.534510] sd 0:0:0:0: [sda] tag#17 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[168487.543576] sd 0:0:0:0: [sda] tag#17 CDB: Read(10) 28 00 01 04 68 b0 00 00 08 00
[168487.551206] blk_update_request: I/O error, dev sda, sector 17066160
[168787.813941] sd 0:0:0:0: [sda] tag#20 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[168787.822951] sd 0:0:0:0: [sda] tag#20 CDB: Read(10) 28 00 01 04 68 b0 00 00 08 00
[168787.830544] blk_update_request: I/O error, dev sda, sector 17066160

Eventually, I could not do anything on the system.  Not even a 'reboot'.  I had to do a cold power cycle to bring things back.

Is there anything to do about this or trash the drive and start anew?

Make sure the cables and power supply are ok.  Try the drive in another machine
that has a different controller to see if there is an incompatibility between
the drive and the controller.

You could make a btrfs file system on the whole device: that should say that
a trim operation is performed for the whole device.  Maybe that helps.

This is a Centos7-armv7hl install which is done by dd the provided image onto a drive, so really can't alter the provided file systems much other than to resize them.  What I have is:

Perhaps there´s some incompatibility on this architecture.

BTW, that the cables sit tight doesn´t mean they are good.



Model: ATA KINGSTON SV300S3 (scsi)
Disk /dev/sda: 240GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:

Number  Start   End     Size    Type     File system     Flags
 1      1049kB  1075MB  1074MB  primary  ext3
 2      1075MB  2149MB  1074MB  primary  linux-swap(v1)
 3      2149MB  240GB   238GB   primary  ext4





If the errors persist, replace the drive.  I´d use Intel SSDs because they
seam to have the least problems with broken firmwares.  Do not use SSDs with
hardware RAID controllers unless the SSDs were designed for this application.



_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
https://lists.centos.org/mailman/listinfo/centos




[Index of Archives]     [CentOS]     [CentOS Announce]     [CentOS Development]     [CentOS ARM Devel]     [CentOS Docs]     [CentOS Virtualization]     [Carrier Grade Linux]     [Linux Media]     [Asterisk]     [DCCP]     [Netdev]     [Xorg]     [Linux USB]


  Powered by Linux