Re: trouble booting install CD on old machine

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]



On Wed, Sep 14, 2011 at 09:57:54PM -0700, Keith Keller wrote:
> Hi all,
> 
> I'm having a bit of an issue booting the full 5.7 install CD on an older
> machine.  I downloaded the ISOs earlier today, checked the sha1sums, and
> burned the CDs with no reported errors.  But when I try to boot, the
> isolinux banner comes up quickly, but then instead of the boot prompt, I
> get a completely blank screen.  After 30-60 seconds, I get a message in
> purple, the exact wording I don't recall, but something like "can't
> boot, please restart".
> 
> Many years ago I put CentOS 4 on this machine, so I know it can boot CD
> media, and earlier today I booted an older UBCD, so I know that it can
> successfully boot from CD at the present time.  (I didn't have time to
> test the CD I burned in another box; I will do that next time I have the
> CD.)
> 
> What other options do I have for getting 5.7 on this box?  I have a few
> ideas:
> 
> --do some troubleshooting with the 5.7 CD.  I don't really know how to
> go about this, and there's no guarantee it'll end up with being able to
> boot in the end.
> --perhaps an older CentOS 5 ISO will work better?  Testing this will be
> fairly quick but is not sure to work.
> --remove the system disk, put it into another system that is known to
> boot the 5.7 CD, install there, then put the disk back.  This could be
> somewhat time consuming (the machine is in a rack, and the system drive
> is buried in the chassis, not hot-swappable), but is pretty sure to work.
> --try to boot from USB.  As I said, it's an old box, so I'm not sure it
> supports booting over USB media.  There were no "boot from USB" options
> in the BIOS; I could try to flash the firmware, but that seems excessive
> for this sort of issue.
> 
> Other thoughts/suggestions?  Any ideas why I'd be seeing this particular
> boot behavior?  It's not something I've seen before; either booting
> fails before even reaching isolinux, or the kernel panics on finding some
> exotic and/or broken piece of hardware.
> 
> --keith
> 
> -- 
> kkeller@xxxxxxxxxxxxxxxxxxxxxxxxxx
> 

Keith, I don't see that you identify what sort of old machine you're
trying to use.

You should be aware that current versions of Centos/RHEL REQUIRE some 
flavor of i686-class processor at minimum. that means Pentium Pro/Pentium II
or later. 

Of course, you may also be hitting some situation where there's some really
obsolete hardware in the machine for which newer systems don't have the
driver built in.

or a bad image burn, too, since you say you haven't yet tested it.

Good luck!

-- 
---- Fred Smith -- fredex@xxxxxxxxxxxxxxxxxxxxxx -----------------------------
    "Not everyone who says to me, 'Lord, Lord,' will enter the kingdom of
     heaven, but only he who does the will of my Father who is in heaven."
------------------------------ Matthew 7:21 (niv) -----------------------------
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos


[Index of Archives]     [CentOS]     [CentOS Announce]     [CentOS Development]     [CentOS ARM Devel]     [CentOS Docs]     [CentOS Virtualization]     [Carrier Grade Linux]     [Linux Media]     [Asterisk]     [DCCP]     [Netdev]     [Xorg]     [Linux USB]
  Powered by Linux