> Hi, > replying to a mail from two months back: > drwho@xxxxxxxxxxxx writes: >> I just got a UB134C which has a QCA ar9375. I tried it in Ubuntu 14.04 beta 2 kernel = >> 3.13.0-22-generic #44-Ubuntu SMP Wed Apr 2 20:04:41 UTC 2014 i686 I'm told the 9375 is an ath6kl, but it doesn't look like the ath6kl driver >> supports it. kernel output..... >> new high-speed USB device number 4 using ehci-pci >> [175257.129911] usb 1-2: New USB device found, idVendor=0cf3, >> idProduct=9375 >> [175257.129923] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 >> [175257.129931] usb 1-2: Product: USBWLAN >> [175257.129939] usb 1-2: Manufacturer: Qualcomm Atheros. >> [175257.129946] usb 1-2: SerialNumber: 12345678 > I just sent patches to add ar6004 hw3.0 support. If you can, please test those and give feedback. Ok, I rebuilt the Ubuntu kernel with your 6 patches, sudo modprobe ath6kl_usb insert ar9375 At first I was getting an error about not being able find the firmware file, so I renamed your fw-5.bin to fw.ram.bin. Now I get...... [ 105.212065] usb 2-1: new high-speed USB device number 3 using ehci-pci [ 105.344939] usb 2-1: New USB device found, idVendor=0cf3, idProduct=9375 [ 105.344944] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 105.344948] usb 2-1: Product: USBWLAN [ 105.344951] usb 2-1: Manufacturer: Qualcomm Atheros. [ 105.344953] usb 2-1: SerialNumber: 12345678 [ 140.212654] usb 2-1: Direct firmware load failed with error -2 [ 140.212660] usb 2-1: Falling back to user helper [ 140.213580] usb 2-1: Direct firmware load failed with error -2 [ 140.213584] usb 2-1: Falling back to user helper [ 140.215225] usb 2-1: Direct firmware load failed with error -2 [ 140.215230] usb 2-1: Falling back to user helper [ 141.232254] ath6kl: Failed to submit usb control message: -110 [ 141.232259] ath6kl: unable to send the bmi data to the device: -110 [ 141.232263] ath6kl: Unable to write to the device: -110 [ 141.232265] ath6kl: Failed to write firmware: -110 [ 141.239999] ath6kl: Failed to start hardware: -110 [ 141.240132] ath6kl: Failed to init ath6kl core: -110 [ 141.240215] ath6kl_usb: probe of 2-1:1.0 failed with error -110 [ 141.240251] usbcore: registered new interface driver ath6kl_usb I then replaced your fw.ram.bin and bdata.bin with the firmware from ATH6KL-LSDK-WLAN-AIO-OSR-5.0.0.110 and the device registers now.... [ 264.596614] usb 2-1: USB disconnect, device number 6 [ 295.384085] usb 2-1: new high-speed USB device number 7 using ehci-pci [ 295.517925] usb 2-1: New USB device found, idVendor=0cf3, idProduct=9375 [ 295.517937] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 295.517946] usb 2-1: Product: USBWLAN [ 295.517954] usb 2-1: Manufacturer: Qualcomm Atheros. [ 295.517961] usb 2-1: SerialNumber: 12345678 [ 295.521134] usb 2-1: Direct firmware load failed with error -2 [ 295.521144] usb 2-1: Falling back to user helper [ 295.523720] usb 2-1: Direct firmware load failed with error -2 [ 295.523729] usb 2-1: Falling back to user helper [ 295.527415] usb 2-1: Direct firmware load failed with error -2 [ 295.527426] usb 2-1: Falling back to user helper [ 295.760488] ath6kl: ar6004 hw 3.0 usb fw 5.0.0.110 api 1 [ 295.760502] ath6kl: firmware supports: 64bit-rates,ap-inactivity-mins [ 295.784446] systemd-udevd[2781]: renamed network interface wlan1 to wlan2 [ 295.795658] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 295.796058] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 322.236793] IPv6: ADDRCONF(NETDEV_CHANGE): wlan2: link becomes ready however it looks like it can not fully authenticate. repeatedly doing "iw wlan2 link" briefly shows a connection, then not connected. Network manager repeatedly tries to connect. I also put your patches into backports and tried it on an arm with wpa_supplicant. wpa_supplicant keeps trying to re associate. I can run wpa_supplicant with -dd if you want? Jon _______________________________________________ ath6kl mailing list ath6kl@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/ath6kl
