/var/log/syslog says:
---------
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 16
VP_IDE: not 100%% native mode: will probe irqs later
Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
PDC20267: IDE controller on PCI bus 00 dev 58
PDC20267: chipset revision 2
PDC20267: not 100%% native mode: will probe irqs later
spurious 8259A interrupt: IRQ7.
PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER Mode.
ide2: BM-DMA at 0x8800-0x8807, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x8808-0x880f, BIOS settings: hdg:pio, hdh:DMA
PDC20265: IDE controller on PCI bus 00 dev 88
PDC20265: chipset revision 2
PDC20265: not 100%% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
PDC20265: FORCING BURST BIT 0x00 -> 0x01 ACTIVE
ide4: BM-DMA at 0x6800-0x6807, BIOS settings: hdi:pio, hdj:pio
ide5: BM-DMA at 0x6808-0x680f, BIOS settings: hdk:DMA, hdl:pio
hda: IBM-DTLA-307045, ATA DISK drive
hdc: Pioneer DVD-ROM ATAPIModel DVD-106S 010, ATAPI CD/DVD-ROM drive
hdd: SONY CD-RW CRX140E, ATAPI CD/DVD-ROM drive
hde: WDC WD800JB-00CRA1, ATA DISK drive
hdf: WDC WD800JB-00CRA1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xa000-0xa007,0x9802 on irq 10
----------
I noticed in the syslog above that the controllers report pio and DMA in a to me unlogical way. Don't know if it's part of the problem though.
/var/log/messages says:
---------
Uniform Multi-Platform E-IDE driver Revision: 6.31
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:04.1
PCI: Found IRQ 10 for device 00:0b.0
PCI: Sharing IRQ 10 with 00:11.0
PCI: Found IRQ 10 for device 00:11.0
PCI: Sharing IRQ 10 with 00:0b.0
hda: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=5606/255/63, UDMA(66)
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100)
hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3 hda4
hde: [PTBL] [9729/255/63] hde1 hde2
hdf: unknown partition table
--------
hde and hdf are the raid drives.
In the kernel, besides pdc 202xx support (static), I also include Special UDMA feature (also static), but not the Special FastTrak feature.
Do I also need the "Multiple devices driver support (RAID and LVM)"? I have seen no info on this anywhere, I thought it only applies to scsi cards, or am I wrong here?
I have created the ataraid devices in dev, but fdisk -l on those devs reports nothing.
I appreciate all the help I can get with this!
_________________________________________________________________
MSN Photos is the easiest way to share and print your photos: http://photos.msn.com/support/worldwide.aspx
