|
Hardware:
MB ABIT VP6, on-board HPT-370 raid (enabled, but
not currently used)
Dual PIII 1GZ
1GB Ram
1 x 80GB disk OS, etc
1 x Promise FastTrak TX4 (20270) bios configured
for 0+1
4 x 80GB disk on FastTrak
OS:
Mandrake 8.0
kernel 2.4.10 compiled with
(Yes) Support for IDE Raid
controllers
(Yes) Support Promise
software RAID
(Module) Highpoint 370
software RAID.
What I would like:
1. To set raid up
successfully using the current version of linux I have installed, but will do
whatever is need to the kernel.
2. Would like to use
Rieserfs.
2. Be able to add 4
additional drives to the HPT-370 raid later to expand storage.
I have gone out, read many how-to's and remarks on
how to do this. I have been unsuccessful in making it work. Here is
part of the dmesg... also the whole message is attached. Lookis like my
ide is doing only 33MHz, how do I change it to 100?
Thanks
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xcc00-0xcc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xcc08-0xcc0f, BIOS settings: hdc:DMA, hdd:pio HPT370A: IDE controller on PCI bus 00 dev 70 HPT370A: chipset revision 4 HPT370A: not 100% native mode: will probe irqs later ide2: BM-DMA at 0xe000-0xe007, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at 0xe008-0xe00f, BIOS settings: hdg:pio, hdh:pio PDC20268: IDE controller on PCI bus 02 dev 08 PDC20268: chipset revision 2 PDC20268: not 100% native mode: will probe irqs later ide4: BM-DMA at 0xa000-0xa007, BIOS settings: hdi:pio, hdj:pio ide5: BM-DMA at 0xa008-0xa00f, BIOS settings: hdk:pio, hdl:pio PDC20268: IDE controller on PCI bus 02 dev 10 PDC20268: chipset revision 2 PDC20268: not 100% native mode: will probe irqs later ide6: BM-DMA at 0xb400-0xb407, BIOS settings: hdm:pio, hdn:pio ide7: BM-DMA at 0xb408-0xb40f, BIOS settings: hdo:pio, hdp:pio hda: WDC WD800BB-00BSA0, ATA DISK drive hdc: YAMAHA CRW2100E, ATAPI CD/DVD-ROM drive hdi: WDC WD800BB-00BSA0, ATA DISK drive hdk: WDC WD800BB-00BSA0, ATA DISK drive hdm: WDC WD800BB-00BSA0, ATA DISK drive hdo: WDC WD800BB-00BSA0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide4 at 0x9000-0x9007,0x9402 on irq 11 ide5 at 0x9800-0x9807,0x9c02 on irq 11 ide6 at 0xa400-0xa407,0xa802 on irq 11 ide7 at 0xac00-0xac07,0xb002 on irq 11 hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63 hdi: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63 hdk: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63 hdm: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63 hdo: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63 Partition check: hda: hda1 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 > hdi: hdi1 hdk: hdk1 hdm: hdm1 hdo: hdo1 |
Attachment:
this
Description: Binary data
