Hi Torrey, I've the SGW box configured as normal and the Asterisk box configured as the master clock source. SGW wanpipe1.conf: > #================================================ > # WANPIPE1 Configuration File > #================================================ > # > # Date: Wed Dec 6 20:29:03 UTC 2006 > # > # Note: This file was generated automatically > # by /usr/local/sbin/setup-sangoma program. > # > # If you want to edit this file, it is > # recommended that you use wancfg program > # to do so. > #================================================ > # Sangoma Technologies Inc. > #================================================ > > [devices] > wanpipe1 = WAN_AFT_TE1, Comment > > [interfaces] > w1g1 = wanpipe1, , TDM_VOICE, Comment > > [wanpipe1] > CARD_TYPE = AFT > S514CPU = A > CommPort = PRI > AUTO_PCISLOT = NO > PCISLOT = 4 > PCIBUS = 5 > FE_MEDIA = E1 > FE_LCODE = HDB3 > FE_FRAME = CRC4 > FE_LINE = 1 > TE_CLOCK = NORMAL > TE_REF_CLOCK = 0 > TE_SIG_MODE = CCS > TE_HIGHIMPEDANCE = NO > TE_RX_SLEVEL = 430 > HW_RJ45_PORT_MAP = DEFAULT > LBO = 120OH > FE_TXTRISTATE = NO > MTU = 1500 > UDPPORT = 9000 > TTL = 255 > IGNORE_FRONT_END = NO > TDMV_SPAN = 1 > TDMV_DCHAN = 0 > TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS Blue > Alarm and keep line down > #wanpipemon -i w1g1 -c Ttx_ais_off to > disable AIS maintenance mode > #wanpipemon -i w1g1 -c Ttx_ais_on to > enable AIS maintenance mode > TDMV_HW_DTMF = NO # YES: receive dtmf events from hardware > TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz events > from hardware > HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation > enabled with nlp (default) > # OCT_SPEECH: improves software > tone detection by disabling NLP (echo possible) > # OCT_NO_ECHO:disables echo > cancelation but allows VQE/tone functions. > HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of > incoming media (must have hwdtmf enabled) > HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on the > line - could break fax > HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic echo > cancelation > HWEC_NLP_DISABLE = NO # NO: default YES: guarantees software > tone detection (possible echo) > HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio > level to be maintained (-20 default) > HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio > level to be maintained (-20 default) > HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to be > applied to tx signal > HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to be > applied to tx signal > > [w1g1] > ACTIVE_CH = ALL > TDMV_HWEC = YES > MTU = 8 > > Asterisk wanpipe1.conf > #================================================ > # WANPIPE1 Configuration File > #================================================ > # > # Date: Wed Dec 6 20:29:03 UTC 2006 > # > # Note: This file was generated automatically > # by /usr/local/sbin/setup-sangoma program. > # > # If you want to edit this file, it is > # recommended that you use wancfg program > # to do so. > #================================================ > # Sangoma Technologies Inc. > #================================================ > > [devices] > wanpipe1 = WAN_AFT_TE1, Comment > > [interfaces] > w1g1 = wanpipe1, , TDM_VOICE, Comment > > [wanpipe1] > CARD_TYPE = AFT > S514CPU = A > CommPort = PRI > AUTO_PCISLOT = NO > PCISLOT = 4 > PCIBUS = 2 > FE_MEDIA = E1 > FE_LCODE = HDB3 > FE_FRAME = CRC4 > FE_LINE = 1 > TE_CLOCK = MASTER > TE_REF_CLOCK = 0 > TE_SIG_MODE = CCS > TE_HIGHIMPEDANCE = NO > TE_RX_SLEVEL = 430 > HW_RJ45_PORT_MAP = DEFAULT > LBO = 120OH > FE_TXTRISTATE = NO > MTU = 1500 > UDPPORT = 9000 > TTL = 255 > IGNORE_FRONT_END = NO > TDMV_SPAN = 1 > TDMV_DCHAN = 0 > TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS Blue > Alarm and keep line down > #wanpipemon -i w1g1 -c Ttx_ais_off to > disable AIS maintenance mode > #wanpipemon -i w1g1 -c Ttx_ais_on to > enable AIS maintenance mode > TDMV_HW_DTMF = NO # YES: receive dtmf events from hardware > TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz events > from hardware > HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation > enabled with nlp (default) > # OCT_SPEECH: improves software > tone detection by disabling NLP (echo possible) > # OCT_NO_ECHO:disables echo > cancelation but allows VQE/tone functions. > HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of > incoming media (must have hwdtmf enabled) > HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on the > line - could break fax > HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic echo > cancelation > HWEC_NLP_DISABLE = NO # NO: default YES: guarantees software > tone detection (possible echo) > HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio > level to be maintained (-20 default) > HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio > level to be maintained (-20 default) > HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to be > applied to tx signal > HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to be > applied to tx signal > > [w1g1] > ACTIVE_CH = ALL > TDMV_HWEC = NO > MTU = 8 > > On Mon, Oct 1, 2012 at 10:44 AM, Torrey Searle <tsearle at gmail.com> wrote: > With wanpipe cards, I believe you need to also configure the timing > information into the wanpipe config files too. > (/etc/wanpipe/wanpipe*.conf) > > Torrey > > On 1 October 2012 09:11, Victor Neiman <victor at blacksheepdev.co.za> wrote: > > Hi, > > > > I'm trying to get SS7 communication between Asterisk 1.8.16.0 which has > > libss7 installed and the Mobicents Signalling Gateway , using Sangoma > A101 > > hardware in two boxes. Both boxes are using wanrouter and dahdi. One > box is > > running Asterisk, the other Mobicents. I have been corresponding closely > > with people at Mobicents to get the configuration right for their > software > > and am fairly sure it is correct. The problem is that when I start up the > > Mobicents Signalling Gateway, Asterisk on the other side immediately > fills > > up with these errors: > > > >> [Oct 1 10:55:46] NOTICE[19825]: chan_dahdi.c:3437 > >> my_handle_link_exception: SS7 got event: HDLC Abort(6) on span 1/0 > > > > > > > > The box that is running the SGW has the following /etc/dahdi/system.conf: > > > >> #autogenerated by /usr/sbin/wancfg_dahdi do not hand edit > >> #autogenrated on 2012-09-28 > >> #Dahdi Channels Configurations > >> #For detailed Dahdi options, view /etc/dahdi/system.conf.bak > >> loadzone=us > >> defaultzone=us > >> > >> #Sangoma A101 port 1 [slot:4 bus:5 span:1] <wanpipe1> > >> span=1,1,0,ccs,hdb3,crc4 > >> bchan=1-31 > > > > > > This config comes straight from the guys at Mobicents. All channels are > > bchan. > > > > The Asterisk side looks like this, /etc/dahdi/sysem.conf > > > >> #autogenerated by /usr/sbin/wancfg_dahdi do not hand edit > >> #autogenrated on 2012-09-28 > >> #Dahdi Channels Configurations > >> #For detailed Dahdi options, view /etc/dahdi/system.conf.bak > >> loadzone=us > >> defaultzone=us > >> > >> #Sangoma A101 port 1 [slot:4 bus:2 span:1] <wanpipe1> > >> span=1,0,0,ccs,hdb3,crc4 > >> bchan=2-31 > >> mtp2=1 > > > > > > /etc/asterisk/chan_dahdi,conf looks like this: > > > >> ;autogenerated by /usr/sbin/wancfg_dahdi do not hand edit > >> ;autogenrated on 2012-09-28 > >> ;Dahdi Channels Configurations > >> ;For detailed Dahdi options, view /etc/asterisk/chan_dahdi.conf.bak > >> > >> [trunkgroups] > >> > >> [channels] > >> context=default > >> usecallerid=yes > >> hidecallerid=no > >> callwaiting=yes > >> usecallingpres=yes > >> callwaitingcallerid=yes > >> threewaycalling=yes > >> transfer=yes > >> canpark=yes > >> cancallforward=yes > >> callreturn=yes > >> echocancel=yes > >> echocancelwhenbridged=yes > >> relaxdtmf=yes > >> rxgain=0.0 > >> txgain=0.0 > >> group=1 > >> callgroup=1 > >> pickupgroup=1 > >> immediate=no > >> > >> ;Sangoma A102 port 1 [slot:2 bus:6 span:1] <wanpipe1> > >> context=from-pstn > >> group=0 > >> echocancel=no > >> signaling=ss7 ;this is ss7 signaling > >> ss7type=itu ;using the ITU variant > >> ss7_called_nai=dynamic ;NAI for outgoing calls > >> ss7_calling_nai=dynamic ;NAI for incoming calls > >> ss7_internationalprefix=00 ;international prefix value for incoming > calls > >> ss7_nationalprefix=0 ;national prefix value for incoming calls > >> ss7_subscriberprefix= ;subscriber prefix value for incoming calls > >> ss7_unknownprefix= ;unknown prefix value for incoming calls > >> ss7_explictacm=yes ;ACM is send as soon as call enters the dial > plan...may > >> not accepted yet though > >> linkset=1 ;arbitrary name for this set of channels > >> pointcode=1 ;the point code for this system...aka SPC > >> adjpointcode=2 ;the point code for the system that we are signaling > to... > >> aka APC > >> defaultdpc=2 ;the point code for the system that the CICs will be > >> negotiated with...aka DPC > >> networkindicator=international ;NI value for MTP3 > >> cicbeginswith=1 ;the starting value of the CICs > >> channel=2-31 ;the channels that are CICs > >> sigchan=1 ;the signaling channel > > > > > > Any help would be appreciated. Feels like I'm missing something in the > > configs but I just can't seem to pin it down. > > > > Regards > > Victor > > > > > > > > -- > > _____________________________________________________________________ > > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > > > asterisk-ss7 mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > -- > _____________________________________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-ss7/attachments/20121001/87297ba6/attachment-0001.htm>
|