Hello again, On Fri, 6 Mar 2009 21:09:28 +0200, Kaloyan Kovachev wrote > On Fri, 06 Mar 2009 12:33:40 -0600, Matthew Fredrickson wrote > > Kaloyan Kovachev wrote: > > > another problem ... > > > when CGB for CIC 1 with range 30 is received CIC 17 remains non blocked and > > > when a call is attemted it pickups CIC 17 ... then it gets a BLO (for 17) > > > and when received its is properly put in blocking state. > > > > > > The same behavior is on CGB for 17 with range 14 - CIC 17 remains available. > > > On CGB for 1 with range 14 it properly sets 1 to 15 as blocked. > > > > > > When local blocking is requested from cli the status is properly displayed. > > > > > > in chan_dahdi.conf: > > > > > > cicbeginswith=1 > > > channel => 1-15 > > > cicbeginswith=17 > > > channel => 17-31 > > > sigchan=16 > > > > Can you post a debug of this when it's occurring? > > This i could not repeat with two Asterisk, because Asterisk says invalid cic - range on such requests, but here is the log from the real link with: pointcode = 2000 adjpointcode = 1001 defaultdpc = 1000 It is similar when all CICs are blocked and an unblock request is received i.e. CIC 17 stays blocked > > Unfortunately i didn't save it, so will need to repeat it on monday, but when > i looked at the debug it was that the other side is sending blocking request > for CIC 1 with range 30 and 'ss7 show cics' shown 17 as idle. At this time > there was a call on CIC 31 (marked as remotely blocked), which was not > interrupted until the other side have sent GRS with the same CIC and range > > > Also, can you post your chan_dahdi.conf as well? > > > > here is the ss7 related part located at the end of the chan_dahdi.conf : > > signalling=ss7 > ss7_called_nai=dynamic > ss7_calling_nai=dynamic > ss7_internationalprefix=00 > ss7_nationalprefix=0 > linkset=1 > networkindicator=national > group=1 > callgroup=1 > pickupgroup=1 > context=Span1 > ss7type=itu > pointcode=X > adjpointcode=Y > defaultdpc=Z > cicbeginswith=1 > channel => 1-15 > cicbeginswith=17 > channel => 17-31 > sigchan=16 > #include ss7.timers > > the adjpointcode is different from the defaultdpc and the included file is > with the default timers listed earlier in the config. > > and the system.conf content: > > # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) > span=1,1,0,ccs,hdb3,crc4 > bchan=1-15,17-31 > #dchan=16 > mtp2=16 > alaw=1-15,17-31 > #echocanceller=mg2,1-15,17-31 > > # ready for PRI ... change signaling if SS7 > # Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2" > span=2,0,0,ccs,hdb3,crc4 > bchan=32-46,48-62 > dchan=47 > alaw=32-46,48-62 > #echocanceller=mg2,32-46,48-62 > > loadzone = bg > defaultzone=bg > > > Thanks, > > Matthew Fredrickson > > Digium, Inc. > > > > _______________________________________________ > > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > > > asterisk-ss7 mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > _______________________________________________ > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 -------------- next part -------------- A non-text attachment was scrubbed... Name: block1-30 Type: application/octet-stream Size: 8495 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-ss7/attachments/20090311/3eba09d0/attachment-0001.obj
|