Hi Antoine, Did you get around to using this setup with full 8 E1s? It would be very helpful if you could post your results. Regards HASSAN On Wed, Apr 8, 2009 at 2:22 AM, Antoine Megalla<aatef at rocketmail.com> wrote: > > Thank you Anders, > > It seems like it is working now. > Although I could not test with the full 8 E1s, but I tested on 2 E1s, one in each server and it is working. > > When I test with the 8 E1s I?will report back. > > Thank you and best regards, > > Antoine Megalla. > > > > ----- Original Message ---- > From: Anders Baekgaard <ab at dicea.dk> > To: asterisk-ss7 at lists.digium.com > Sent: Thursday, April 2, 2009 3:05:25 PM > Subject: Re: [asterisk-ss7] chan_ss7 signalling across multiple servers > > The config spec looks correct. > > You will not need a [cluster] section when you use mtp3d to transport > signaling for multiple servers. > > You can also configure a cluster using the [cluster] section, and then not use > mtp3d. There is a template ss7.conf for that in the source distribution. > > The method of configuring clusters using the [cluster] section is the old > approach. The newer approach of using mtp3d was introduced as a step towards > supporting SIGTRAN, and for support of sharing transport for other protocols > like GSM MAP and INAP. > > Best regards, > -- > Anders Baekgaard > Managing Director, Dicea ApS > Esromgade 15, 1110 > DK-2200 Copenhagen N > Denmark > Tel: +45 46931411 > Fax: +45 46931466 > Mobile: +45 20771844 > > On Thursday 02 April 2009 14:03:00 Antoine Megalla wrote: >> Hi, >> >> So I wrote 1 ss7.conf for both servers as suggested, I just need comments >> if the file looks correct, or if it missing anything: Do I need a [cluster] >> section in the file: >> >> Here is my ss7.conf file: >> >> [linkset-MSC1] >> enabled => yes >> enable_st => no >> use_connect => yes >> hunting_policy => seq_htl >> subservice => auto >> context => ss7 >> language => en >> t35 => 15000,timeout >> >> [link-l1] >> linkset => MSC1 >> channels => 1-15,17-31 >> schannel => 16,host1:12000 >> firstcic => 1 >> echocancel => no >> echocan_train => 350 >> echocan_taps => 128 >> enabled => yes >> >> [link-l2] >> linkset => MSC1 >> channels => 1-31 >> schannel => >> firstcic => 33 >> echocancel=allways >> echocan_taps=32 >> echocan_train=350 >> enabled => yes >> >> [link-l3] >> linkset => MSC1 >> channels => 1-31 >> schannel => >> firstcic => 65 >> echocancel=no >> echocan_taps=32 >> echocan_train=350 >> enabled => yes >> >> [link-l4] >> linkset => MSC1 >> channels => 1-31 >> schannel => >> firstcic => 97 >> echocancel=no >> echocan_taps=32 >> echocan_train=350 >> enabled => yes >> >> [link-l5] >> linkset => MSC1 >> channels => 1-31 >> schannel => >> firstcic => 129 >> echocancel=no >> echocan_taps=32 >> echocan_train=350 >> enabled => yes >> >> [link-l6] >> linkset => MSC1 >> channels => 1-31 >> schannel => >> firstcic => 161 >> echocancel=no >> echocan_taps=32 >> echocan_train=350 >> enabled => yes >> >> [link-l7] >> linkset => MSC1 >> channels => 1-31 >> schannel => >> firstcic => 193 >> echocancel=no >> echocan_taps=32 >> echocan_train=350 >> enabled => yes >> >> [link-l8] >> linkset => MSC1 >> channels => 1-31 >> schannel => >> firstcic => 225 >> echocancel=no >> echocan_taps=32 >> echocan_train=350 >> enabled => yes >> >> [host-host1] >> enabled => yes >> default_linkset => MSC1 >> opc => 1000 >> dpc => MSC1:2000 >> links => l1:1,l2:2,l3:3,l4:4 >> if-1 => 10.0.0.1 >> >> [host-host2] >> enabled => yes >> default_linkset => MSC1 >> opc => 1000 >> dpc => MSC1:2000 >> links => l5:1,l6:2,l7:3,l8:4 >> if-1 => 10.0.0.2 >> >> >> Appreciate your comments, >> >> Regards, >> >> Antoine Megalla. >> >> >> >> >> ----- Original Message ---- >> From: Anders Baekgaard <ab at dicea.dk> >> To: asterisk-ss7 at lists.digium.com >> Sent: Thursday, April 2, 2009 12:03:57 PM >> Subject: Re: [asterisk-ss7] chan_ss7 signalling across multiple servers >> >> Assuming link 'l1' has signaling on ts 16, and this is connected on server >> 'host1', you will write >> >> [link-l1] >> ... >> schannel => 16, host1:12000 >> ... >> >> >> You must specify this on both servers. It is easiest to have the same >> configuration specification (ss7.conf) on both servers. chan_ss7 will >> forward signaling using TCP/IP to 'host1', port 12000, so you must ensure >> mtp3d is running on that server. >> >> Best regards, > > > _______________________________________________ > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > ? http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > > > > > _______________________________________________ > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > ? http://lists.digium.com/mailman/listinfo/asterisk-ss7 > >
|