Anton wrote: > Try adjusting too, but in my case i did not need to modify > it. Actually I see that message appearing several times, > and after 3-4 timeouts finally receiving GRA > > On Monday 21 July 2008 11:34, Low Yu Siang wrote: >> I am connecting to a Siemens switch. I waited for hours, >> T23 timer are also appearing. Currently I see in the >> chan_ss7 code that the timeout value is set at 30 >> seconds, are you suggesting that I should modify the code >> so that it is >120 seconds? >> >> Thanks. >> Yu Siang >> >> --- On Mon, 21/7/08, Anton <anton.vazir at gmail.com> wrote: >>> From: Anton <anton.vazir at gmail.com> >>> Subject: Re: [asterisk-ss7] chan_ss7 - T22 timeout (No >>> 'circuit group reset acknowledge' from peer) To: >>> asterisk-ss7 at lists.digium.com, yusiang at yahoo.com Date: >>> Monday, 21 July, 2008, 2:22 PM >>> I have similar issue with connecting to ZTE and HUAWEI >>> switches. GRA comes not imediatelly, but after 1-2 >>> minutes. >>> >>> Maybe you have the same issue. Did you wait long >>> enough? >>> >>> On Saturday 19 July 2008 19:39, Low Yu Siang wrote: >>>> Hi all, >>>> >>>> Thanks to the generous help from Mr. Pawel >>>> Ratajewski, >>> I >>> >>>> have managed to solve the initial alignment >>> problem(was >>> >>>> using the beta version 1.0.93 of chan_ss7 and it is >>>> solved by downgrading to 1.0.0 following some >>> reboots). >>> >>>> But I still couldn't get the ss7 link ready for >>> making >>> >>>> calls. All CIC are in 'idle reset pending' >>> status. The >>> >>>> below's is the log messages. >>>> >>>> [Jul 19 22:26:00] NOTICE[7676]: config.c:549 >>>> load_config_link: Configured link 'l1' on >>> linkset 'siuc', >>> >>>> firstcic=1 [Jul 19 22:26:00] DEBUG[7676]: >>>> config.c:674 load_config_host: links 'l1:1' [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: config.c:693 load_config_host: linkname >>>> 'l1', no 1 [Jul 19 22:26:00] DEBUG[7676]: >>> config.c:711 >>> >>>> load_config_host: host n_spans 1 [Jul 19 22:26:00] >>>> WARNING[7676]: config.c:795 load_config_host: Missing >>>> interface entries for host 'scvideo'. [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: config.c:800 load_config_host: host >>> scvideo, >>> >>>> n_spans 1 [Jul 19 22:26:00] NOTICE[7676]: >>>> config.c:959 load_config: Configuring DPC 12864 for >>>> linkset >>> 'siuc'. >>> >>>> [Jul 19 22:26:00] DEBUG[7676]: config.c:975 >>> load_config: >>>> Setting linkset 0 'siuc' enabled 1 [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: config.c:173 show_config: Host scvideo, >>>> links 1, ifs 0 [Jul 19 22:26:00] DEBUG[7676]: >>>> l4isup.c:4302 isup_init: Links 1, host scvideo [Jul >>>> 19 22:26:00] DEBUG[7676]: l4isup.c:4310 isup_init: >>>> New >>> CIC, >>> >>>> first_zapid 0, channelmask 0x7fff7fff, connector 1, >>>> firstcic 1, schannel 16 [Jul 19 22:26:00] >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>>> CIC 1 on >>> zaptel >>> >>>> device 1. [Jul 19 22:26:00] DEBUG[7676]: >>> transport.c:127 >>> >>>> openchannel: Configuring CIC 2 on zaptel device 2. >>> [Jul >>> >>>> 19 22:26:00] DEBUG[7676]: transport.c:127 >>>> openchannel: Configuring CIC 3 on zaptel device 3. >>>> [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>> CIC >>> >>>> 4 on zaptel device 4. [Jul 19 22:26:00] DEBUG[7676]: >>>> transport.c:127 openchannel: Configuring CIC 5 on >>> zaptel >>> >>>> device 5. [Jul 19 22:26:00] DEBUG[7676]: >>> transport.c:127 >>> >>>> openchannel: Configuring CIC 6 on zaptel device 6. >>> [Jul >>> >>>> 19 22:26:00] DEBUG[7676]: transport.c:127 >>>> openchannel: Configuring CIC 7 on zaptel device 7. >>>> [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>> CIC >>> >>>> 8 on zaptel device 8. [Jul 19 22:26:00] DEBUG[7676]: >>>> transport.c:127 openchannel: Configuring CIC 9 on >>> zaptel >>> >>>> device 9. [Jul 19 22:26:00] DEBUG[7676]: >>> transport.c:127 >>> >>>> openchannel: Configuring CIC 10 on zaptel device 10. >>> [Jul >>> >>>> 19 22:26:00] DEBUG[7676]: transport.c:127 >>>> openchannel: Configuring CIC 11 on zaptel device 11. >>>> [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>> CIC >>> >>>> 12 on zaptel device 12. [Jul 19 22:26:00] >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>>> CIC 13 on >>> zaptel >>> >>>> device 13. [Jul 19 22:26:00] DEBUG[7676]: >>> transport.c:127 >>> >>>> openchannel: Configuring CIC 14 on zaptel device 14. >>> [Jul >>> >>>> 19 22:26:00] DEBUG[7676]: transport.c:127 >>>> openchannel: Configuring CIC 15 on zaptel device 15. >>>> [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>> CIC >>> >>>> 17 on zaptel device 17. [Jul 19 22:26:00] >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>>> CIC 18 on >>> zaptel >>> >>>> device 18. [Jul 19 22:26:00] DEBUG[7676]: >>> transport.c:127 >>> >>>> openchannel: Configuring CIC 19 on zaptel device 19. >>> [Jul >>> >>>> 19 22:26:00] DEBUG[7676]: transport.c:127 >>>> openchannel: Configuring CIC 20 on zaptel device 20. >>>> [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>> CIC >>> >>>> 21 on zaptel device 21. [Jul 19 22:26:00] >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>>> CIC 22 on >>> zaptel >>> >>>> device 22. [Jul 19 22:26:00] DEBUG[7676]: >>> transport.c:127 >>> >>>> openchannel: Configuring CIC 23 on zaptel device 23. >>> [Jul >>> >>>> 19 22:26:00] DEBUG[7676]: transport.c:127 >>>> openchannel: Configuring CIC 24 on zaptel device 24. >>>> [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>> CIC >>> >>>> 25 on zaptel device 25. [Jul 19 22:26:00] >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>>> CIC 26 on >>> zaptel >>> >>>> device 26. [Jul 19 22:26:00] DEBUG[7676]: >>> transport.c:127 >>> >>>> openchannel: Configuring CIC 27 on zaptel device 27. >>> [Jul >>> >>>> 19 22:26:00] DEBUG[7676]: transport.c:127 >>>> openchannel: Configuring CIC 28 on zaptel device 28. >>>> [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>> CIC >>> >>>> 29 on zaptel device 29. [Jul 19 22:26:00] >>>> DEBUG[7676]: transport.c:127 openchannel: Configuring >>>> CIC 30 on >>> zaptel >>> >>>> device 30. [Jul 19 22:26:00] DEBUG[7676]: >>> transport.c:127 >>> >>>> openchannel: Configuring CIC 31 on zaptel device 31. >>> [Jul >>> >>>> 19 22:26:00] DEBUG[7676]: cluster.c:780 >>>> build_sender_list: Found no senders to supervise -- >>>> Starting cluster thread, pid=7676. >>>> [Jul 19 22:26:00] DEBUG[7676]: cluster.c:798 >>>> wait_for_connections: wait 0 0 0 0 -- Starting >>> continuity >>> >>>> check thread, pid=7676. == Registered channel type >>> 'SS7' >>> >>>> (SS7 Protocol Driver) [Jul 19 22:26:00] NOTICE[7676]: >>>> mtp.c:2190 mtp_init: Initialising 1 signalling links >>> -- >>> >>>> Starting MTP thread, pid=7676. >>>> -- SS7 channel loaded successfully. >>>> Loaded chan_ss7 => (SS7 Protocol Support) >>>> The 'load' command is deprecated and will be >>> removed in a >>> >>>> future release. Please use 'module load' >>> instead. *CLI> >>> >>>> -- Starting monitor thread, pid=7676. >>>> [Jul 19 22:26:00] DEBUG[7711]: mtp.c:2085 >>> mtp_init_link: >>>> init link l1, linkset siuc, schannel 16. [Jul 19 >>>> 22:26:00] DEBUG[7711]: mtp.c:681 >>> start_initial_alignment: >>>> Starting initial alignment on link 'l1', >>> reason: Initial. >>> >>>> *CLI> [Jul 19 22:26:00] NOTICE[7711]: mtp.c:1792 >>>> mtp_thread_main: Empty Zaptel output buffer detected, >>>> outgoing packets may have been lost on link >>> 'l1'. [Jul 19 >>> >>>> 22:26:00] DEBUG[7711]: mtp.c:988 mtp2_process_lssu: >>>> Entering proving state for link 'l1'. [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7711]: mtp.c:499 t4_timeout: Proving successful >>> on >>> >>>> link 'l1'. [Jul 19 22:26:00] NOTICE[7711]: >>> mtp.c:1130 >>> >>>> mtp2_good_frame: Sending TRA to peer on link >>> 'l1'.... >>> >>>> [Jul 19 22:26:00] DEBUG[7711]: mtp.c:1567 >>>> mtp2_fill_zaptel_buf: Sending buffer to zaptel len=9, >>> on >>> >>>> link 'l1' bsn=127, fsn=0. [Jul 19 22:26:00] >>> DEBUG[7711]: >>>> mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to >>> zaptel >>> >>>> len=25, on link 'l1' bsn=127, fsn=1. [Jul 19 >>> 22:26:00] >>> >>>> DEBUG[7711]: mtp.c:1250 mtp2_good_frame: Got MSU on >>> link >>> >>>> 'l1' sio=1 slc=0 m.sls=0 bsn=1/1, fsn=1/0, >>> sio=81, >>> >>>> len=15: 47 34 90 0c 11 80 f2 54 5c 10 aa ff 55 00 >>>> [Jul >>> 19 >>> >>>> 22:26:00] DEBUG[7711]: mtp.c:1323 process_msu: Got >>> SLTM, >>> >>>> sending SLTA 'l1', state=5. [Jul 19 22:26:00] >>>> DEBUG[7711]: mtp.c:1567 mtp2_fill_zaptel_buf: Sending >>>> buffer to zaptel len=18, on link 'l1' bsn=0, >>> fsn=2. [Jul >>> >>>> 19 22:26:00] DEBUG[7711]: mtp.c:1250 mtp2_good_frame: >>> Got >>> >>>> MSU on link 'l1' sio=1 slc=0 m.sls=0 bsn=1/1, >>> fsn=1/1, >>> >>>> sio=81, len=22: 47 34 90 0c 21 f0 11 22 33 44 55 66 >>>> 77 >>> 88 >>> >>>> 99 aa bb cc dd ee ff [Jul 19 22:26:00] DEBUG[7711]: >>>> mtp.c:1338 process_msu: Got valid SLTA response on >>> link >>> >>>> 'l1', state=5. [Jul 19 22:26:00] DEBUG[7711]: >>>> l4isup.c:1344 send_init_grs: Sending GROUP RESET >>> messages >>> >>>> on linkset 'siuc'. [Jul 19 22:26:00] >>> DEBUG[7711]: >>>> l4isup.c:389 mtp_enqueue_isup_packet: Queue packet >>> CIC=1, >>> >>>> len=10, linkset='siuc', link='l1', >>> slinkset='siuc', >>> >>>> slink='l1' [Jul 19 22:26:00] DEBUG[7711]: >>> l4isup.c:1377 >>> >>>> send_init_grs: Group reset first 1, range 14 [Jul 19 >>>> 22:26:00] DEBUG[7711]: l4isup.c:389 >>>> mtp_enqueue_isup_packet: Queue packet CIC=17, len=10, >>>> linkset='siuc', link='l1', >>> slinkset='siuc', slink='l1' >>> >>>> [Jul 19 22:26:00] DEBUG[7711]: l4isup.c:1377 >>>> send_init_grs: Group reset first 17, range 14 [Jul 19 >>>> 22:26:00] WARNING[7711]: chan_ss7.c:617 >>>> process_event: MTP is now UP on link 'l1'. [Jul 19 >>>> 22:26:00] DEBUG[7711]: mtp.c:1859 mtp_thread_main: >>>> Queue MSU, lsi=0, last_send_ix=0, linkset=siuc, >>>> m->link=l1 >>> [Jul 19 >>> >>>> 22:26:00] DEBUG[7711]: mtp.c:1859 mtp_thread_main: >>> Queue >>> >>>> MSU, lsi=0, last_send_ix=0, linkset=siuc, >>> m->link=l1 [Jul >>> >>>> 19 22:26:00] DEBUG[7711]: mtp.c:1567 >>>> mtp2_fill_zaptel_buf: Sending buffer to zaptel >>>> len=14, >>> on >>> >>>> link 'l1' bsn=1, fsn=3. [Jul 19 22:26:00] >>> DEBUG[7711]: >>>> mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to >>> zaptel >>> >>>> len=14, on link 'l1' bsn=1, fsn=4. [Jul 19 >>> 22:26:30] >>> >>>> NOTICE[7711]: l4isup.c:1220 t22_timeout: T22 timeout >>> (No >>> >>>> "circuit group reset acknowledge" from peer) >>> CIC=1. [Jul >>> >>>> 19 22:26:30] DEBUG[7711]: l4isup.c:389 >>>> mtp_enqueue_isup_packet: Queue packet CIC=1, len=10, >>>> linkset='siuc', link='l1', >>> slinkset='siuc', slink='l1' >>> >>>> [Jul 19 22:26:30] NOTICE[7711]: l4isup.c:1220 >>>> t22_timeout: T22 timeout (No "circuit group reset >>>> acknowledge" from peer) CIC=17. [Jul 19 22:26:30] >>>> DEBUG[7711]: l4isup.c:389 mtp_enqueue_isup_packet: >>> Queue >>> >>>> packet CIC=17, len=10, linkset='siuc', >>> link='l1', >>> >>>> slinkset='siuc', slink='l1' [Jul 19 >>> 22:26:30] >>> >>>> DEBUG[7711]: mtp.c:1859 mtp_thread_main: Queue MSU, >>>> lsi=0, last_send_ix=0, linkset=siuc, m->link=l1 >>> [Jul 19 >>> >>>> 22:26:30] DEBUG[7711]: mtp.c:1859 mtp_thread_main: >>> Queue >>> >>>> MSU, lsi=0, last_send_ix=0, linkset=siuc, >>> m->link=l1 [Jul >>> >>>> 19 22:26:30] DEBUG[7711]: mtp.c:1567 >>>> mtp2_fill_zaptel_buf: Sending buffer to zaptel >>>> len=14, >>> on >>> >>>> link 'l1' bsn=1, fsn=5. [Jul 19 22:26:30] >>> DEBUG[7711]: >>>> mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to >>> zaptel >>> >>>> len=14, on link 'l1' bsn=1, fsn=6. [Jul 19 >>> 22:27:00] >>> >>>> NOTICE[7711]: l4isup.c:1220 t22_timeout: T22 timeout >>> (No >>> >>>> "circuit group reset acknowledge" from peer) >>> CIC=1. [Jul >>> >>>> 19 22:27:00] DEBUG[7711]: l4isup.c:389 >>>> mtp_enqueue_isup_packet: Queue packet CIC=1, len=10, >>>> linkset='siuc', link='l1', >>> slinkset='siuc', slink='l1' >>> >>>> [Jul 19 22:27:00] NOTICE[7711]: l4isup.c:1220 >>>> t22_timeout: T22 timeout (No "circuit group reset >>>> acknowledge" from peer) CIC=17. [Jul 19 22:27:00] >>>> DEBUG[7711]: l4isup.c:389 mtp_enqueue_isup_packet: >>> Queue >>> >>>> packet CIC=17, len=10, linkset='siuc', >>> link='l1', >>> >>>> slinkset='siuc', slink='l1' >>>> >>>> Any help would be greatly appreciated. Thank you! >>>> >>>> Regards, >>>> Low Yu Siang >>> _______________________________________________________ >>> __ >>> >>>> _ Not happy with your email address?. >>>> Get the one you really want - millions of new email >>>> addresses available now at Yahoo! >>>> http://uk.docs.yahoo.com/ymail/new.html >>>> >>>> _______________________________________________ >>>> --Bandwidth and Colocation Provided by >>>> http://www.api-digital.com-- >>>> >>>> asterisk-ss7 mailing list >>>> To UNSUBSCRIBE or update options visit: >>> http://lists.digium.com/mailman/listinfo/asterisk-ss7 >> >> _________________________________________________________ >> _ Not happy with your email address?. >> Get the one you really want - millions of new email >> addresses available now at Yahoo! >> http://uk.docs.yahoo.com/ymail/new.html > > _______________________________________________ > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 > I have connected to siemens ewsd16 without stress and its on production for close to 18months now without much problem. Thanks goksie
|