Anton, Paul, Joseph, Thanks for your assistance and suggestions to date. Based on the information you provided, I think I may have narrowed the source ot the problem down the the timing source. I have my end of the link set as NORMAL in the Sangoma config and Zaptel config. This is obvious for me in a Q931/PRI context but I'm not sure how signalling works on an SS7 context. Is SS7 similar to PRI in that I need a master timing source? Can I ask you folks how you have set up you timing? My Zaptel config is: #Sangoma A108 port 1 [slot:4 bus:13 span:1] <wanpipe1> span=1,0,0,ccs,hdb3,crc4 bchan=1-31 And the wanpipe1.conf is below. Thanks again, Barry [devices] wanpipe1 = WAN_AFT_TE1, Comment [interfaces] w1g1 = wanpipe1, , TDM_VOICE, Comment [wanpipe1] CARD_TYPE = AFT S514CPU = A CommPort = PRI AUTO_PCISLOT = NO PCISLOT = 4 PCIBUS = 13 FE_MEDIA = E1 FE_LCODE = HDB3 FE_FRAME = CRC4 FE_LINE = 1 TE_CLOCK = NORMAL TE_REF_CLOCK = 0 TE_SIG_MODE = CCS TE_HIGHIMPEDANCE = NO LBO = 120OH FE_TXTRISTATE = NO MTU = 1500 UDPPORT = 9000 TTL = 255 IGNORE_FRONT_END = NO TDMV_SPAN = 1 TDMV_DCHAN = 0 TDMV_HW_DTMF = NO [w1g1] ACTIVE_CH = ALL TDMV_ECHO_OFF = NO TDMV_HWEC = NO On Thursday 24 April 2008 09:58:02 Anton wrote: > I do use sangoma A108 card with chan_ss7 - if you have HW > echocancellers on board - they does bother. Trying > cancelling an echo on sigchannel. dig mailing list for > sangoma settings to deal with this. > > On Thursday 24 April 2008 00:36, Barry O'Donovan wrote: > > Hi folks, > > > > I'm trying to use either libss7 (preferably) or chan_ss7 > > with a Sangoma A108 card but I have issues with both. To > > summarise, the issue appears to be that the port will not > > enter a "CONNECTED" state but rather stays in a > > "Connecting" state and so I cannot pass frames on it. At > > least this is what I believe the issue is. > > > > For libss7, I used current (today's) Asterisk trunk, > > libpri trunk, Zaptel 1.4, libss7 trunk and wanpipe-3.2.5. > > > > For chan_ss7, I used current Asterisk 1.4 from SVN, > > libpri-1.4, Zaptel 1.4 and wanpipe-3.2.5 again. > > > > In both cases, the SS7 link was in NOT_ALIGNED and I > > could not progress it any further. I tried all manner of > > combinations of CIC numbering, etc from the expected to > > the crazy. > > > > The other end of the SS7 is a Nortel DMS100. > > > > I'm posting relevent command outputs and configs below > > for the chan_ss7 set-up (I'd need to reinstall trunk for > > libss7). > > > > Any pointers would be greatly appreciated. > > > > Thanks, > > Barry > > > > ######################################################### > >################# > > ######################################################### > >################# > > > > # wanpipemon -i w1g1 -c Ta > > > > ***** w1g1: E1 Alarms (Framer) ***** > > > > ALOS: OFF | LOS: OFF > > RED: ON | AIS: OFF > > OOF: ON | RAI: OFF > > > > > > ***** w1g1: E1 Performance Monitoring Counters ***** > > > > Line Code Violation : 745 > > Far End Block Errors : 0 > > CRC4 Errors : 0 > > FAS Errors : 0 > > > > > > Rx Level : > -2.5db > > > > > > ######################################################### > >################# > > ######################################################### > >################# > > > > # wanrouter status > > > > Devices currently active: > > wanpipe1 > > > > > > Wanpipe Config: > > > > Device name | Protocol Map | Adapter | IRQ | Slot/IO | > > If's | CLK | Baud rate | > > wanpipe1 | N/A | A101/1D/A102/2D/4/4D/8| 16 > > > > | 4 | 1 | EXT | 0 | > > > > Wanrouter Status: > > > > Device name | Protocol | Station | Status | > > wanpipe1 | AFT HDLC | N/A | Connecting | > > > > > > ######################################################### > >################# > > ######################################################### > >################# > > > > # ifconfig > > > > w1g1 Link encap:Point-to-Point Protocol > > UP POINTOPOINT NOARP MTU:8 Metric:1 > > RX packets:0 errors:0 dropped:0 overruns:0 > > frame:0 TX packets:0 errors:0 dropped:0 overruns:0 > > carrier:0 collisions:0 txqueuelen:100 > > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > > Interrupt:16 Memory:ffffc20000d00000-d01fff > > > > > > ######################################################### > >################# > > ######################################################### > >################# > > > > # cat /etc/wanpipe/wanpipe1.conf > > #================================================ > > # WANPIPE1 Configuration File > > #================================================ > > # > > # Date: Wed Dec 6 20:29:03 UTC 2006 > > # > > # Note: This file was generated automatically > > # by /usr/local/sbin/setup-sangoma program. > > # > > # If you want to edit this file, it is > > # recommended that you use wancfg program > > # to do so. > > #================================================ > > # Sangoma Technologies Inc. > > #================================================ > > > > [devices] > > wanpipe1 = WAN_AFT_TE1, Comment > > > > [interfaces] > > w1g1 = wanpipe1, , TDM_VOICE, Comment > > > > [wanpipe1] > > CARD_TYPE = AFT > > S514CPU = A > > CommPort = PRI > > AUTO_PCISLOT = NO > > PCISLOT = 4 > > PCIBUS = 13 > > FE_MEDIA = E1 > > FE_LCODE = HDB3 > > FE_FRAME = CRC4 > > FE_LINE = 1 > > TE_CLOCK = NORMAL > > TE_REF_CLOCK = 0 > > TE_SIG_MODE = CCS > > TE_HIGHIMPEDANCE = NO > > LBO = 120OH > > FE_TXTRISTATE = NO > > MTU = 1500 > > UDPPORT = 9000 > > TTL = 255 > > IGNORE_FRONT_END = NO > > TDMV_SPAN = 1 > > TDMV_DCHAN = 0 > > TDMV_HW_DTMF = NO > > > > [w1g1] > > ACTIVE_CH = ALL > > TDMV_ECHO_OFF = NO > > TDMV_HWEC = YES > > > > > > ######################################################### > >################# > > ######################################################### > >################# > > > > > > # cat /etc/zaptel.conf > > > > > > #Sangoma A108 port 1 [slot:4 bus:13 span:1] <wanpipe1> > > span=1,0,0,ccs,hdb3,crc4 > > bchan=1-31 > > > > > > ######################################################### > >################# > > ######################################################### > >################# > > > > # cat /etc/asterisk/ss7.conf > > > > [linkset-siuc] > > > > enabled => yes > > enable_st => no > > use_connect => no > > hunting_policy => seq_lth > > context => ss7 > > language => en > > t35 => 15000,timeout > > subservice => auto > > > > [link-l1] > > > > linkset => siuc > > channels => 1-15,17-31 > > schannel => 16 > > firstcic => 1 > > enabled => yes > > > > echocancel => no > > echocan_train => 350 > > echocan_taps => 128 > > > > > > [host-A-Host] > > > > enabled => yes > > opc => 0x1 > > dpc => siuc:0x39B0 > > links => l1:1 > > > > ; The SCCP global title: translation-type, > > nature-of-address, numbering-plan, address > > globaltitle => 0x00, 0x04, 0x01, 4546931411 > > ssn => 7 > > > > ######################################################### > >################# > > ######################################################### > >################# > > > > *CLI> unload chan_ss7.so > > > > The 'unload' command is deprecated and will be removed in > > a future release. Please use 'module unload' instead. > > == Unregistered channel type 'SS7' > > -- SS7 channel unloaded. > > > > *CLI> load chan_ss7.so > > > > The 'load' command is deprecated and will be removed in a > > future release. Please use 'module load' instead. > > == Parsing '/etc/asterisk/ss7.conf': Found > > [Apr 23 20:35:30] NOTICE[21479]: config.c:549 > > load_config_link: Configured link 'l1' on linkset 'siuc', > > firstcic=1 > > [Apr 23 20:35:30] WARNING[21479]: config.c:795 > > load_config_host: Missing interface entries for host > > 'A-Host'. > > [Apr 23 20:35:30] NOTICE[21479]: config.c:959 > > load_config: Configuring DPC 14768 for linkset 'siuc'. > > -- Starting cluster thread, pid=21438. > > -- Starting continuity check thread, pid=21438. > > == Registered channel type 'SS7' (SS7 Protocol Driver) > > [Apr 23 20:35:30] NOTICE[21479]: mtp.c:2190 mtp_init: > > Initialising 1 signalling links > > -- Starting MTP thread, pid=21438. > > -- SS7 channel loaded successfully. > > Loaded chan_ss7.so => (SS7 Protocol Support) > > -- Starting monitor thread, pid=21438. > > [Apr 23 20:35:30] NOTICE[21487]: mtp.c:1792 > > mtp_thread_main: Empty Zaptel output buffer detected, > > outgoing packets may have been lost on link 'l1'. > > > > (and after some time:) > > > > [Apr 23 20:36:45] WARNING[21487]: mtp.c:457 t2_timeout: > > MTP2 timer T2 timeout (failed to receive 'O', 'N', or 'E' > > after sending 'O'), initial alignment failed on link > > 'l1'. > > > > > > > > *CLI> ss7 linestat > > Linkset: siuc> > > CIC 1 Idle Reset pending > > CIC 2 Idle Reset pending > > CIC 3 Idle Reset pending > > CIC 4 Idle Reset pending > > CIC 5 Idle Reset pending > > CIC 6 Idle Reset pending > > CIC 7 Idle Reset pending > > CIC 8 Idle Reset pending > > CIC 9 Idle Reset pending > > CIC 10 Idle Reset pending > > CIC 11 Idle Reset pending > > CIC 12 Idle Reset pending > > CIC 13 Idle Reset pending > > CIC 14 Idle Reset pending > > CIC 15 Idle Reset pending > > CIC 17 Idle Reset pending > > CIC 18 Idle Reset pending > > CIC 19 Idle Reset pending > > CIC 20 Idle Reset pending > > CIC 21 Idle Reset pending > > CIC 22 Idle Reset pending > > CIC 23 Idle Reset pending > > CIC 24 Idle Reset pending > > CIC 25 Idle Reset pending > > CIC 26 Idle Reset pending > > CIC 27 Idle Reset pending > > CIC 28 Idle Reset pending > > CIC 29 Idle Reset pending > > CIC 30 Idle Reset pending > > CIC 31 Idle Reset pending > > > > > > *CLI> ss7 link status > > linkset siuc, link l1, schannel 16, sls 0, NOT_ALIGNED, > > rx: 0, tx: 4/4, sentseq/lastack: 127/127, total > > 933920, 934016 > > > > > > *CLI> ss7 show channels > > Linkset: siuc> > > CIC 1 Idle Reset pending > > CIC 2 Idle Reset pending > > CIC 3 Idle Reset pending > > CIC 4 Idle Reset pending > > CIC 5 Idle Reset pending > > CIC 6 Idle Reset pending > > CIC 7 Idle Reset pending > > CIC 8 Idle Reset pending > > CIC 9 Idle Reset pending > > CIC 10 Idle Reset pending > > CIC 11 Idle Reset pending > > CIC 12 Idle Reset pending > > CIC 13 Idle Reset pending > > CIC 14 Idle Reset pending > > CIC 15 Idle Reset pending > > CIC 17 Idle Reset pending > > CIC 18 Idle Reset pending > > CIC 19 Idle Reset pending > > CIC 20 Idle Reset pending > > CIC 21 Idle Reset pending > > CIC 22 Idle Reset pending > > CIC 23 Idle Reset pending > > CIC 24 Idle Reset pending > > CIC 25 Idle Reset pending > > CIC 26 Idle Reset pending > > CIC 27 Idle Reset pending > > CIC 28 Idle Reset pending > > CIC 29 Idle Reset pending > > CIC 30 Idle Reset pending > > CIC 31 Idle Reset pending > > > > > > *CLI> ss7 status > > linkset idle busy initiating resetting total > > incoming total outgoing siuc 0 0 > > 0 30 0 0 *** Idle list > > lenth is: 30 > > > > > > > > *CLI> ss7 version > > chan_ss7 version 1.0.0 > > > > > > > > _______________________________________________ > > --Bandwidth and Colocation Provided by > > http://www.api-digital.com-- > > > > asterisk-ss7 mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-ss7 -- Kind regards, Barry O'Donovan +353 86 801 7669 http://www.opensolutions.ie/ Open Source Solutions Ltd 51 Limes Road, Wedgewood, Dundrum, Dublin 16 1890 929 300 +353 1 293 2184 Open Source Solutions Limited is a company registered in the Republic of Ireland (#438231). Open Source Solutions Limited trades as Open Solutions (registered business name #329120). PGP Key: http://www.opensolutions.ie/barryo-pgp.key
|