I do use sangoma A108 card with chan_ss7 - if you have HW echocancellers on board - they does bother. Trying cancelling an echo on sigchannel. dig mailing list for sangoma settings to deal with this. On Thursday 24 April 2008 00:36, Barry O'Donovan wrote: > Hi folks, > > I'm trying to use either libss7 (preferably) or chan_ss7 > with a Sangoma A108 card but I have issues with both. To > summarise, the issue appears to be that the port will not > enter a "CONNECTED" state but rather stays in a > "Connecting" state and so I cannot pass frames on it. At > least this is what I believe the issue is. > > For libss7, I used current (today's) Asterisk trunk, > libpri trunk, Zaptel 1.4, libss7 trunk and wanpipe-3.2.5. > > For chan_ss7, I used current Asterisk 1.4 from SVN, > libpri-1.4, Zaptel 1.4 and wanpipe-3.2.5 again. > > In both cases, the SS7 link was in NOT_ALIGNED and I > could not progress it any further. I tried all manner of > combinations of CIC numbering, etc from the expected to > the crazy. > > The other end of the SS7 is a Nortel DMS100. > > I'm posting relevent command outputs and configs below > for the chan_ss7 set-up (I'd need to reinstall trunk for > libss7). > > Any pointers would be greatly appreciated. > > Thanks, > Barry > > ######################################################### >################# > ######################################################### >################# > > # wanpipemon -i w1g1 -c Ta > > ***** w1g1: E1 Alarms (Framer) ***** > > ALOS: OFF | LOS: OFF > RED: ON | AIS: OFF > OOF: ON | RAI: OFF > > > ***** w1g1: E1 Performance Monitoring Counters ***** > > Line Code Violation : 745 > Far End Block Errors : 0 > CRC4 Errors : 0 > FAS Errors : 0 > > > Rx Level : > -2.5db > > > ######################################################### >################# > ######################################################### >################# > > # wanrouter status > > Devices currently active: > wanpipe1 > > > Wanpipe Config: > > Device name | Protocol Map | Adapter | IRQ | Slot/IO | > If's | CLK | Baud rate | > wanpipe1 | N/A | A101/1D/A102/2D/4/4D/8| 16 > | 4 | 1 | EXT | 0 | > > Wanrouter Status: > > Device name | Protocol | Station | Status | > wanpipe1 | AFT HDLC | N/A | Connecting | > > > ######################################################### >################# > ######################################################### >################# > > # ifconfig > > w1g1 Link encap:Point-to-Point Protocol > UP POINTOPOINT NOARP MTU:8 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 > frame:0 TX packets:0 errors:0 dropped:0 overruns:0 > carrier:0 collisions:0 txqueuelen:100 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:16 Memory:ffffc20000d00000-d01fff > > > ######################################################### >################# > ######################################################### >################# > > # cat /etc/wanpipe/wanpipe1.conf > #================================================ > # WANPIPE1 Configuration File > #================================================ > # > # Date: Wed Dec 6 20:29:03 UTC 2006 > # > # Note: This file was generated automatically > # by /usr/local/sbin/setup-sangoma program. > # > # If you want to edit this file, it is > # recommended that you use wancfg program > # to do so. > #================================================ > # Sangoma Technologies Inc. > #================================================ > > [devices] > wanpipe1 = WAN_AFT_TE1, Comment > > [interfaces] > w1g1 = wanpipe1, , TDM_VOICE, Comment > > [wanpipe1] > CARD_TYPE = AFT > S514CPU = A > CommPort = PRI > AUTO_PCISLOT = NO > PCISLOT = 4 > PCIBUS = 13 > FE_MEDIA = E1 > FE_LCODE = HDB3 > FE_FRAME = CRC4 > FE_LINE = 1 > TE_CLOCK = NORMAL > TE_REF_CLOCK = 0 > TE_SIG_MODE = CCS > TE_HIGHIMPEDANCE = NO > LBO = 120OH > FE_TXTRISTATE = NO > MTU = 1500 > UDPPORT = 9000 > TTL = 255 > IGNORE_FRONT_END = NO > TDMV_SPAN = 1 > TDMV_DCHAN = 0 > TDMV_HW_DTMF = NO > > [w1g1] > ACTIVE_CH = ALL > TDMV_ECHO_OFF = NO > TDMV_HWEC = YES > > > ######################################################### >################# > ######################################################### >################# > > > # cat /etc/zaptel.conf > > > #Sangoma A108 port 1 [slot:4 bus:13 span:1] <wanpipe1> > span=1,0,0,ccs,hdb3,crc4 > bchan=1-31 > > > ######################################################### >################# > ######################################################### >################# > > # cat /etc/asterisk/ss7.conf > > [linkset-siuc] > > enabled => yes > enable_st => no > use_connect => no > hunting_policy => seq_lth > context => ss7 > language => en > t35 => 15000,timeout > subservice => auto > > [link-l1] > > linkset => siuc > channels => 1-15,17-31 > schannel => 16 > firstcic => 1 > enabled => yes > > echocancel => no > echocan_train => 350 > echocan_taps => 128 > > > [host-A-Host] > > enabled => yes > opc => 0x1 > dpc => siuc:0x39B0 > links => l1:1 > > ; The SCCP global title: translation-type, > nature-of-address, numbering-plan, address > globaltitle => 0x00, 0x04, 0x01, 4546931411 > ssn => 7 > > ######################################################### >################# > ######################################################### >################# > > *CLI> unload chan_ss7.so > > The 'unload' command is deprecated and will be removed in > a future release. Please use 'module unload' instead. > == Unregistered channel type 'SS7' > -- SS7 channel unloaded. > > *CLI> load chan_ss7.so > > The 'load' command is deprecated and will be removed in a > future release. Please use 'module load' instead. > == Parsing '/etc/asterisk/ss7.conf': Found > [Apr 23 20:35:30] NOTICE[21479]: config.c:549 > load_config_link: Configured link 'l1' on linkset 'siuc', > firstcic=1 > [Apr 23 20:35:30] WARNING[21479]: config.c:795 > load_config_host: Missing interface entries for host > 'A-Host'. > [Apr 23 20:35:30] NOTICE[21479]: config.c:959 > load_config: Configuring DPC 14768 for linkset 'siuc'. > -- Starting cluster thread, pid=21438. > -- Starting continuity check thread, pid=21438. > == Registered channel type 'SS7' (SS7 Protocol Driver) > [Apr 23 20:35:30] NOTICE[21479]: mtp.c:2190 mtp_init: > Initialising 1 signalling links > -- Starting MTP thread, pid=21438. > -- SS7 channel loaded successfully. > Loaded chan_ss7.so => (SS7 Protocol Support) > -- Starting monitor thread, pid=21438. > [Apr 23 20:35:30] NOTICE[21487]: mtp.c:1792 > mtp_thread_main: Empty Zaptel output buffer detected, > outgoing packets may have been lost on link 'l1'. > > (and after some time:) > > [Apr 23 20:36:45] WARNING[21487]: mtp.c:457 t2_timeout: > MTP2 timer T2 timeout (failed to receive 'O', 'N', or 'E' > after sending 'O'), initial alignment failed on link > 'l1'. > > > > *CLI> ss7 linestat > Linkset: siuc> > CIC 1 Idle Reset pending > CIC 2 Idle Reset pending > CIC 3 Idle Reset pending > CIC 4 Idle Reset pending > CIC 5 Idle Reset pending > CIC 6 Idle Reset pending > CIC 7 Idle Reset pending > CIC 8 Idle Reset pending > CIC 9 Idle Reset pending > CIC 10 Idle Reset pending > CIC 11 Idle Reset pending > CIC 12 Idle Reset pending > CIC 13 Idle Reset pending > CIC 14 Idle Reset pending > CIC 15 Idle Reset pending > CIC 17 Idle Reset pending > CIC 18 Idle Reset pending > CIC 19 Idle Reset pending > CIC 20 Idle Reset pending > CIC 21 Idle Reset pending > CIC 22 Idle Reset pending > CIC 23 Idle Reset pending > CIC 24 Idle Reset pending > CIC 25 Idle Reset pending > CIC 26 Idle Reset pending > CIC 27 Idle Reset pending > CIC 28 Idle Reset pending > CIC 29 Idle Reset pending > CIC 30 Idle Reset pending > CIC 31 Idle Reset pending > > > *CLI> ss7 link status > linkset siuc, link l1, schannel 16, sls 0, NOT_ALIGNED, > rx: 0, tx: 4/4, sentseq/lastack: 127/127, total > 933920, 934016 > > > *CLI> ss7 show channels > Linkset: siuc> > CIC 1 Idle Reset pending > CIC 2 Idle Reset pending > CIC 3 Idle Reset pending > CIC 4 Idle Reset pending > CIC 5 Idle Reset pending > CIC 6 Idle Reset pending > CIC 7 Idle Reset pending > CIC 8 Idle Reset pending > CIC 9 Idle Reset pending > CIC 10 Idle Reset pending > CIC 11 Idle Reset pending > CIC 12 Idle Reset pending > CIC 13 Idle Reset pending > CIC 14 Idle Reset pending > CIC 15 Idle Reset pending > CIC 17 Idle Reset pending > CIC 18 Idle Reset pending > CIC 19 Idle Reset pending > CIC 20 Idle Reset pending > CIC 21 Idle Reset pending > CIC 22 Idle Reset pending > CIC 23 Idle Reset pending > CIC 24 Idle Reset pending > CIC 25 Idle Reset pending > CIC 26 Idle Reset pending > CIC 27 Idle Reset pending > CIC 28 Idle Reset pending > CIC 29 Idle Reset pending > CIC 30 Idle Reset pending > CIC 31 Idle Reset pending > > > *CLI> ss7 status > linkset idle busy initiating resetting total > incoming total outgoing siuc 0 0 > 0 30 0 0 *** Idle list > lenth is: 30 > > > > *CLI> ss7 version > chan_ss7 version 1.0.0 > > > > _______________________________________________ > --Bandwidth and Colocation Provided by > http://www.api-digital.com-- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7
|