Re: Slow memory access when using OpenCL without X11

["Deucher, Alexander" <Alexander.Deucher@xxxxxxx>]

Forcing the sclk and mclk high may impact the CPU frequency since they share TDP.

Alex

---

From: amd-gfx <amd-gfx-bounces@xxxxxxxxxxxxxxxxxxxxx> on behalf of Lauri Ehrenpreis <laurioma@xxxxxxxxx>
Sent: Tuesday, March 12, 2019 5:31 PM
To: Kuehling, Felix
Cc: Tom St Denis; amd-gfx@xxxxxxxxxxxxxxxxxxxxx
Subject: Re: Slow memory access when using OpenCL without X11

 

However it's not only related to mclk and sclk. I tried this:

rocm-smi  --setsclk 2

rocm-smi  --setmclk 3

rocm-smi

========================        ROCm System Management Interface        ========================

================================================================================================

GPU   Temp   AvgPwr   SCLK    MCLK    PCLK           Fan     Perf    PwrCap   SCLK OD   MCLK OD  GPU%

GPU[0] : WARNING: Empty SysFS value: pclk

GPU[0] : WARNING: Unable to read /sys/class/drm/card0/device/gpu_busy_percent

0     34.0c  N/A      1240Mhz 1333Mhz N/A            0%      manual  N/A      0%        0%       N/A      

================================================================================================

========================               End of ROCm SMI Log              ========================

./cl_slow_test 1

got 1 platforms 1 devices

speed 3919.777100 avg 3919.777100 mbytes/s

speed 3809.373291 avg 3864.575195 mbytes/s

speed 585.796814 avg 2771.649170 mbytes/s

speed 188.721848 avg 2125.917236 mbytes/s

speed 188.916367 avg 1738.517090 mbytes/s

So despite forcing max sclk and mclk the memory speed is still slow..

--

Lauri

On Tue, Mar 12, 2019 at 11:21 PM Lauri Ehrenpreis <laurioma@xxxxxxxxx> wrote:

IN the case when memory is slow, the rocm-smi outputs this:

========================        ROCm System Management Interface        ========================

================================================================================================

GPU   Temp   AvgPwr   SCLK    MCLK    PCLK           Fan     Perf    PwrCap   SCLK OD   MCLK OD  GPU%

GPU[0] : WARNING: Empty SysFS value: pclk

GPU[0] : WARNING: Unable to read /sys/class/drm/card0/device/gpu_busy_percent

0     30.0c  N/A      400Mhz  933Mhz  N/A            0%      auto    N/A      0%        0%       N/A      

================================================================================================

========================               End of ROCm SMI Log              ========================

normal memory speed case gives following:

========================        ROCm System Management Interface        ========================

================================================================================================

GPU   Temp   AvgPwr   SCLK    MCLK    PCLK           Fan     Perf    PwrCap   SCLK OD   MCLK OD  GPU%

GPU[0] : WARNING: Empty SysFS value: pclk

GPU[0] : WARNING: Unable to read /sys/class/drm/card0/device/gpu_busy_percent

0     35.0c  N/A      400Mhz  1200Mhz N/A            0%      auto    N/A      0%        0%       N/A      

================================================================================================

========================               End of ROCm SMI Log              ========================

So there is a difference in MCLK - can this cause such a huge slowdown?

--

Lauri  

On Tue, Mar 12, 2019 at 6:39 PM Kuehling, Felix <Felix.Kuehling@xxxxxxx> wrote:

[adding the list back]

I'd suspect a problem related to memory clock. This is an APU where
system memory is shared with the CPU, so if the SMU changes memory
clocks that would affect CPU memory access performance. If the problem
only occurs when OpenCL is running, then the compute power profile could
have an effect here.

Laurie, can you monitor the clocks during your tests using rocm-smi?

Regards,
   Felix

On 2019-03-11 1:15 p.m., Tom St Denis wrote:
> Hi Lauri,
>
> I don't have ROCm installed locally (not on that team at AMD) but I
> can rope in some of the KFD folk and see what they say :-).
>
> (in the mean time I should look into installing the ROCm stack on my
> Ubuntu disk for experimentation...).
>
> Only other thing that comes to mind is some sort of stutter due to
> power/clock gating (or gfx off/etc).  But that typically affects the
> display/gpu side not the CPU side.
>
> Felix:  Any known issues with Raven and ROCm interacting over memory
> bus performance?
>
> Tom
>
> On Mon, Mar 11, 2019 at 12:56 PM Lauri Ehrenpreis <laurioma@xxxxxxxxx
> <mailto:laurioma@xxxxxxxxx>> wrote:
>
>     Hi!
>
>     The 100x memory slowdown is hard to belive indeed. I attached the
>     test program with my first e-mail which depends only on
>     rocm-opencl-dev package. Would you mind compiling it and checking
>     if it slows down memory for you as well?
>
>     steps:
>     1) g++ cl_slow_test.cpp -o cl_slow_test -I
>     /opt/rocm/opencl/include/ -L /opt/rocm/opencl/lib/x86_64/  -lOpenCL
>     2) logout from desktop env and disconnect hdmi/diplayport etc
>     3) log in over ssh
>     4) run the program ./cl_slow_test 1
>
>     For me it reproduced even without step 2 as well but less
>     reliably. moving mouse for example could make the memory speed
>     fast again.
>
>     --
>     Lauri
>
>
>
>     On Mon, Mar 11, 2019 at 6:33 PM Tom St Denis <tstdenis82@xxxxxxxxx
>     <mailto:tstdenis82@xxxxxxxxx>> wrote:
>
>         Hi Lauri,
>
>         There's really no connection between the two other than they
>         run in the same package.  I too run a 2400G (as my
>         workstation) and I got the same ~6.6GB/sec transfer rate but
>         without a CL app running ...  The only logical reason is your
>         CL app is bottlenecking the APUs memory bus but you claim
>         "simply opening a context is enough" so something else is
>         going on.
>
>         Your last reply though says "with it running in the
>         background" so it's entirely possible the CPU isn't busy but
>         the package memory controller (shared between both the CPU and
>         GPU) is busy.  For instance running xonotic in a 1080p window
>         on my 4K display reduced the memory test to 5.8GB/sec and
>         that's hardly a heavy memory bound GPU app.
>
>         The only other possible connection is the GPU is generating so
>         much heat that it's throttling the package which is also
>         unlikely if you have a proper HSF attached (I use the ones
>         that came in the retail boxes).
>
>         Cheers,
>         Tom
>

_______________________________________________
amd-gfx mailing list
amd-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/amd-gfx