Add device tree documentation for Cirrus Logic CS35L36
speaker amplifier
Signed-off-by: James Schulman <james.schulman@xxxxxxxxxx>
Reviewed-by: Charles Keepax <ckeepax@xxxxxxxxxxxxxxxxxxxxx>
Acked-by: Brian Austin <brian.austin@xxxxxxxxxx>
---
.../devicetree/bindings/sound/cs35l36.txt | 168 +++++++++++++++++++++
1 file changed, 168 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/cs35l36.txt
diff --git a/Documentation/devicetree/bindings/sound/cs35l36.txt b/Documentation/devicetree/bindings/sound/cs35l36.txt
new file mode 100644
index 0000000..912bd16
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs35l36.txt
@@ -0,0 +1,168 @@
+CS35L36 Speaker Amplifier
+
+Required properties:
+
+ - compatible : "cirrus,cs35l36"
+
+ - reg : the I2C address of the device for I2C
+
+ - VA-supply, VP-supply : power supplies for the device,
+ as covered in
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+ - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
+ converter's output voltage in mV. The range is from 2550mV to 12000mV with
+ increments of 50mV.
+ (Default) VP
+
+ - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
+ Configures the peak current by monitoring the current through the boost FET.
+ Range starts at 1600mA and goes to a maximum of 4500mA with increments of
+ 50mA.
+ (Default) 4.50 Amps
+
+ - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
+ Seeds the digital boost converter's inductor estimation block with the initial
+ inductance value to reference.
+
+ 1000 = 1uH (Default)
+ 1200 = 1.2uH
+
+Optional properties:
+ - cirrus,multi-amp-mode : Boolean to determine if there are more than
+ one amplifier in the system. If more than one it is best to Hi-Z the ASP
+ port to prevent bus contention on the output signal
+
+ - cirrus,boost-ctl-select : Boost conerter control source selection.
+ Selects the source of the BST_CTL target VBST voltage for the boost
+ converter to generate.
+ 0x00 - Control Port Value
+ 0x01 - Class H Tracking (Default)
+ 0x10 - MultiDevice Sync Value
+
+ - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming
+ PCM data
+
+ - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the
+ polarity of outbound IMON feedback data
+
+ - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the
+ polarity of outbound VMON feedback data
+
+ - cirrus,dcm-mode-enable : Boost converter automatic DCM Mode enable.
+ This enables the digital boost converter to operate in a low power
+ (Discontinuous Conduction) mode during low loading conditions.
+
+ - cirrus,weak-fet-disable : Boolean : The strength of the output drivers is
+ reduced when operating in a Weak-FET Drive Mode and must not be used to drive
+ a large load.
+
+ - cirrus,classh-wk-fet-delay : Weak-FET entry delay. Controls the delay
+ (in ms) before the Class H algorithm switches to the weak-FET voltage
+ (after the audio falls and remains below the value specified in WKFET_AMP_THLD).
+
+ 0 = 0ms
+ 1 = 5ms
+ 2 = 10ms
+ 3 = 50ms
+ 4 = 100ms (Default)
+ 5 = 200ms
+ 6 = 500ms
+ 7 = 1000ms
+
+ - cirrus,classh-weak-fet-thld-millivolt : Weak-FET amplifier drive threshold.
+ Configures the signal threshold at which the PWM output stage enters
+ weak-FET operation. The range is 50mV to 700mV in 50mV increments.
+
+ - cirrus,temp-warn-threshold : Amplifier overtemperature warning threshold.
+ Configures the threshold at which the overtemperature warning condition occurs.
+ When the threshold is met, the overtemperature warning attenuation is applied
+ and the TEMP_WARN_EINT interrupt status bit is set.
+ If TEMP_WARN_MASK = 0, INTb is asserted.
+
+ 0 = 105C
+ 1 = 115C
+ 2 = 125C (Default)
+ 3 = 135C
+
+ - cirrus,irq-drive-select : Selects the driver type of the selected interrupt
+ output.
+
+ 0 = Open-drain
+ 1 = Push-pull (Default)
+
+ - cirrus,irq-gpio-select : Selects the pin to serve as the programmable
+ interrupt output.
+
+ 0 = PDM_DATA / SWIRE_SD / INT (Default)
+ 1 = GPIO
+
+Optional properties for the "cirrus,vpbr-config" Sub-node
+
+ - cirrus,vpbr-en : VBST brownout prevention enable. Configures whether the
+ VBST brownout prevention algorithm is enabled or disabled.
+
+ 0 = VBST brownout prevention disabled (default)
+ 1 = VBST brownout prevention enabled
+
+ See Section 7.31.1 VPBR Config for configuration options & further details
+
+ - cirrus,vpbr-thld : Initial VPBR threshold. Configures the VP brownout
+ threshold voltage
+
+ - cirrus,cirrus,vpbr-atk-rate : Attenuation attack step rate. Configures the
+ amount delay between consecutive volume attenuation steps when a brownout
+ condition is present and the VP brownout condition is in an attacking state.
+
+ - cirrus,vpbr-atk-vol : VP brownout prevention step size. Configures the VP
+ brownout prevention attacking attenuation step size when operating in either
+ digital volume or analog gain modes.
+
+ - cirrus,vpbr-max-attn : Maximum attenuation that the VP brownout prevention
+ can apply to the audio signal.
+
+ - cirrus,vpbr-wait : Configures the delay time between a brownout condition
+ no longer being present and the VP brownout prevention entering an attenuation
+ release state.
+
+ - cirrus,vpbr-rel-rate : Attenuation release step rate. Configures the delay
+ between consecutive volume attenuation release steps when a brownout condition
+ is not longer present and the VP brownout is in an attenuation release state.
+
+ - cirrus,vpbr-mute-en : During the attack state, if the vpbr-max-attn value
+ is reached, the error condition still remains, and this bit is set, the audio
+ is muted.
+
+Example:
+
+cs35l36: cs35l36@40 {
+ compatible = "cirrus,cs35l36";
+ reg = <0x40>;
+ VA-supply = <&dummy_vreg>;
+ VP-supply = <&dummy_vreg>;
+ reset-gpios = <&gpio0 54 0>;
+ interrupt-parent = <&gpio8>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ cirrus,boost-ind-nanohenry = <1000>;
+ cirrus,boost-ctl-millivolt = <10000>;
+ cirrus,boost-peak-milliamp = <4500>;
+ cirrus,boost-ctl-select = <0x00>;
+ cirrus,weak-fet-delay = <0x04>;
+ cirrus,weak-fet-thld = <0x01>;
+ cirrus,temp-warn-threshold = <0x01>;
+ cirrus,multi-amp-mode;
+ cirrus,irq-drive-select = <0x01>;
+ cirrus,irq-gpio-select = <0x01>;
+
+ cirrus,vpbr-config {
+ cirrus,vpbr-en = <0x00>;
+ cirrus,vpbr-thld = <0x05>;
+ cirrus,vpbr-atk-rate = <0x02>;
+ cirrus,vpbr-atk-vol = <0x01>;
+ cirrus,vpbr-max-attn = <0x09>;
+ cirrus,vpbr-wait = <0x01>;
+ cirrus,vpbr-rel-rate = <0x05>;
+ cirrus,vpbr-mute-en = <0x00>;
+ };
+};
--
1.9.1
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
