2017-12-18 17:31 GMT+08:00 Charles Keepax <ckeepax@xxxxxxxxxxxxxxxxxxxxx>:
> On Fri, Dec 15, 2017 at 09:07:15PM +0800, chen liu wrote:
> > 2017-12-15 0:19 GMT+08:00 Charles Keepax <ckeepax@xxxxxxxxxxxxxxxxxxxxx
> >:
> > > On Wed, Dec 13, 2017 at 08:37:30PM +0800, Chen.Liu wrote:
> > When the MCLK clock frequency cannot meet the SYSCLK clock
> > frequency of the wm8960 codec,we must use the PLL divider to
> > generate the clock frequency.
> >
> > For what you are talking about setting the SYSCLK clock frequency
> > automatically and manually,the difference is that one uses the PLL
> > divider to generate the SYSCLK clock frequency and the other one
> > provides the SYSCLK clock frequency directly through the MCLK.
> >
> > Although the driver already supports setting the SYSCLK_DIV register,
> > it can only be set to 1,thus causing the codec to not support multiple
> > MCLK clock frequency.(For more information, please see the wm8960
> > codec manual)
> >
> > The important purpose of this patch is to support multiple MCLK
> > clock frequency.
>
> Sorry I think I am not following something here, could you be a
> bit more specific, especially about why the automatic approach
> doesn't meet your needs.
>
> As far as I can see this will let you set the SYSCLKDIV using the
> manual method and it can be easily set to either 1 or 2:
>
> static int wm8960_set_dai_clkdiv(struct snd_soc_dai *codec_dai,
> ...
> switch (div_id) {
> case WM8960_SYSCLKDIV:
> reg = snd_soc_read(codec, WM8960_CLOCK1) & 0x1f9;
> snd_soc_write(codec, WM8960_CLOCK1, reg | div);
> break;
> ...
>
> And as for the automatic method:
>
> static int wm8960_configure_pll(struct snd_soc_codec *codec, int freq_in,
> ...
> for (i = 0; i < ARRAY_SIZE(sysclk_divs); ++i) {
> if (sysclk_divs[i] == -1) continue;
> ...
>
> This will iterate through all the sysclk_dividers and pick one
> that is appropriate either 1 or 2. So in what way does the
> automatic method not support a SYSCLK_DIV of 2?
>
Hi Charles,
Thanks for your quickly reply.
According to your detailed description above, I understand what you mean.
For the 'wm8960_configure_pll' function,it deduces a reasonable PLL output
clock frequency based on the 'freq_in' frequency,the sample rate,and the bit
clock.
static int wm8960_configure_clocking(struct snd_soc_codec*codec)
...
freq_out = wm8960_configure_pll(codec, freq_in, &i, &j, &k);
if (freq_out < 0) {
dev_err(codec->dev, "failed to configure clock via PLL\n");
return freq_out;
}
wm8960_set_pll(codec, freq_in, freq_out);
...
In the 'wm8960_configure_clocking' function, it sets the PLL divider by
calling
the 'wm8960_set_pll' function after calling the 'wm8960_configure_pll'.
However,there is no support for SYSCLK_DIV = 2 in the 'wm8960_set_pll'
function.
Looking forward to your reply.
Thanks,
Chen.
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
