> There are some hoops to jump through to get access to the
> necessary compilers etc. for the DSP, although again Joao who I
> CCed on your other email would be a good place to start the
> process of getting access to that.
Thank you, this part may come later this year.
> Yeah please avoid doing this, the driver should support all the
> features you require from the sound of things. There should be no
> need to hard code register writes.
>
> What sort of things are you setting up with these register
> writes? Lets see if I can point you in the direction of the
> correct place to put some of those.
Thanks!
The clocking:
regmap_write(arizona->regmap, ARIZONA_CLOCK_32K_1, 0x00042); // Use Sysclk, Default = 0x0041
regmap_write(arizona->regmap, ARIZONA_SYSTEM_CLOCK_1, 0x0200); // Use MCLK1, and 24.576MHz from BBB McASP, Default = 0x0304
These would seem to be the relevant device tree entries from Documentation/devicetree/bindings/mfd/arizona.txt:
- clocks: Should reference the clocks supplied on MCLK1 and MCLK2
- clock-names: Should contains two strings:
"mclk1" for the clock supplied on MCLK1, recommended to be a high
quality audio reference clock
"mclk2" for the clock supplied on MCLK2, recommended to be an always on
32k clock
Still trying to figure out how to specify these. I have pasted our device tree to the end of this email. (Oh, gpio for BBB McASP clock is deliberately routed away from gpio1_27, because somehow we are not convincing the driver to enable it, and so we have a gpio_set_value(MY_CLOCK_GPIO_ENABLE,1); in arizona-core probe until we figure out how.
>> We had to simply disinvite extcon-arizona from the party
>> though. On both the WM5102-6271-CS137-M-SCH-REV2.03 and our
>> protoboard, JACKDET is an IRQ gone wild. On the Wolfson board,
>> inserting my headphones into the jack shut it up. But on our
>> protoboard, where we left that pin unconnected, we found that
>> the probe of extcon-arizona hard enables JACKDET.
>>
> I am surprised you are seeing issues on one of our boards, they
> are all fairly well tested here. I would quite like to see a
> kernel log on that one if I can?
Okay, I’ll hook up the dev board, likely Thurs-Fri after we complete
board bring up.
> Apart from that, this all seems reasonable, the extcon driver
> exists to control the jack detection. If that is not wired up on
> your system then not building in this part of the system seems
> the correct response.
>
> Thanks,
> Charles
Thank you, Clark.
Device Tree _______________________________________
/*
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
#include "am33xx.dtsi"
#include "am335x-bone-common.dtsi"
#include "dt-bindings/mfd/arizona.h"
/ {
model = "TI AM335x BeagleBone Black";
compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
leds {
pinctrl-names = "default";
pinctrl-0 = <&led_pins_default>;
compatible = "gpio-leds";
led@1 {
label= "led_ir";
gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led@2 {
label= "led_red";
gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
ldo18: ldo18 {
compatible = "regulator-fixed";
regulator-name = "DC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
enable-active-high;
regulator-always-on;
};
ldo50: ldo50 { /* BBB VCC_5V */
compatible = "regulator-fixed";
regulator-name = "DC_5V0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
};
clk_audio_fixed: clk_audio_fixed {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24576000>;
};
clk_audio: clk_audio {
#clock-cells = <0>;
compatible = "gpio-gate-clock";
clocks = <&clk_audio_fixed>;
enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; /* BeagleBone Black Clk enable on GPIO1_27 */
};
sound: sound@0 {
status = "okay";
compatible = "simple-audio-card";
simple-audio-card,name = "WM5102";
simple-audio-card,widgets =
"Line", "Line In";
simple-audio-card,routing =
"IN1L", "Line In",
"IN1R", "Line In",
"IN2L", "Line In",
"IN2R", "Line In",
"IN3L", "Line In",
"IN3R", "Line In";
/* simple-audio-card,hp-det-gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; /*TP38*/
/*simple-audio-card,dai-link {*/
simple-audio-card,format = "dsp_b";
simple-audio-card,bitclock-master = <&sound_master>;
simple-audio-card,frame-master = <&sound_master>;
simple-audio-card,cpu {
sound-dai = <&mcasp0>;
clocks = <&clk_audio>;
/*
dai-tdm-slot-num = <6>;
dai-tdm-slot-width = <32>;
*/
};
sound_master: simple-audio-card,codec {
sound-dai = <&wm5102>;
clocks = <&clk_audio>;
system-clock-id = <1>; /* ARIZONA_CLK_SYSCLK */
/*
dai-tdm-slot-num = <6>;
dai-tdm-slot-width = <32>;
*/
};
/* };*/
};
};
&ldo3_reg {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
&mmc1 {
vmmc-supply = <&vmmcsd_fixed>;
};
&mmc2 {
vmmc-supply = <&vmmcsd_fixed>;
pinctrl-names = "default";
pinctrl-0 = <&emmc_pins>;
bus-width = <8>;
status = "okay";
};
&am33xx_pinmux {
nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
pinctrl-single,pins = <
0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
0x18c ( PIN_INPUT_PULLUP | MUX_MODE0 ) /* (C16) I2C0_SCL.I2C0_SCL */
0x188 ( PIN_INPUT_PULLUP | MUX_MODE0 ) /* (C17) I2C0_SDA.I2C0_SDA */
>;
};
nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
pinctrl-single,pins = <
0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */
0x18c ( PIN_INPUT | MUX_MODE0 ) /* (C16) I2C0_SCL.I2C0_SCL */
0x188 ( PIN_INPUT | MUX_MODE0 ) /* (C17) I2C0_SDA.I2C0_SDA */
>;
};
led_pins_default: led_pins_default {
pinctrl-single,pins = <
0x178 ( PIN_OUTPUT | MUX_MODE7 ) /* (D18) uart1_ctsn.gpio0[12] TP38 */
0x17c ( PIN_OUTPUT | MUX_MODE7 ) /* (D17) uart1_rtsn.gpio0[13] TP39 */
0x28 ( PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (T11) gpmc_ad10.gpio0[26] IR LED */
0x38 ( PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (V13) gpmc_ad14.gpio1[14] RED LED */
>;
};
accel_pins_default: accel_pins_default {
pinctrl-single,pins = <
0xe8 ( PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (V5) lcd_pclk.gpio2[24] ACCEL_ST */
0xec ( PIN_OUTPUT_PULLUP | MUX_MODE7 ) /* (R6) lcd_ac_bias_en.gpio2[25] ACCEL_FS */
>;
};
mcasp0_slave_pins_default: mcasp0_slave_pins_default {
pinctrl-single,pins = <
0x1a0 ( PIN_INPUT | MUX_MODE0 ) /* (B12) mcasp0_aclkr.mcasp0_aclkr */
0x1a4 ( PIN_INPUT | MUX_MODE0 ) /* (C13) mcasp0_fsr.mcasp0_fsr */
0x198 ( PIN_INPUT | MUX_MODE0 ) /* (D12) mcasp0_axr0.mcasp0_axr0 */
0x19c ( PIN_OUTPUT | MUX_MODE2 ) /* (C12) mcasp0_ahclkr.mcasp0_axr2 */
>;
};
wm5102_pins_default: wm5102_pins_default {
pinctrl-single,pins = <
0x6c ( PIN_OUTPUT_PULLUP | MUX_MODE7 ) /* (V17) gpmc_a11.gpio1[27] 24.576 MHZ CE */
0x78 ( PIN_OUTPUT_PULLDOWN | MUX_MODE7 ) /* (U18) gpmc_be1n.gpio1[28] /RESET */
0x7c ( PIN_OUTPUT_PULLUP | MUX_MODE7 ) /* (V6) gpmc_csn0.gpio1[29] LDOENA */
0xe4 ( PIN_INPUT | MUX_MODE7 ) /* (R5) lcd_hsync.gpio2[23] /IRQ */
0x1ac ( PIN_INPUT_PULLUP | MUX_MODE0 ) /* (A14) mcasp0_ahclkx.gpio3[21] AUDIO_MCLK */
0x15c ( PIN_INPUT_PULLUP | MUX_MODE2 ) /* (A16) spi0_cs0.I2C1_SCL */
0x158 ( PIN_INPUT_PULLUP | MUX_MODE2 ) /* (B16) spi0_d1.I2C1_SDA */
0x164 ( PIN_INPUT | MUX_MODE7 ) /* (C18) eCAP0_in_PWM0_out.gpio0[7] (AUDIO BCLK) HIGHZ*/
>;
};
};
&lcdc {
status = "disabled";
port {
lcdc_0: endpoint@0 {
remote-endpoint = <&hdmi_0>;
};
};
};
&i2c0 {
tda19988 {
compatible = "nxp,tda998x";
reg = <0x70>;
pinctrl-names = "default", "off";
pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
port {
hdmi_0: endpoint@0 {
remote-endpoint = <&lcdc_0>;
};
};
};
};
&i2c1 {
pinctrl-names = "default";
pintctrl-0 = <&wm5102_pins_default>;
status = "okay";
clock-frequency = <400000>;
wm5102: wm5102@1b {
compatible = "wlf,wm5102";
reg = <0x1b>;
status = "okay";
/* /IRQ is connected to GPIO2_23. Mask from HiassofT DT for cirrus audio board was 8 */
interrupts = <23 8>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&gpio2>;
/*clock-names = "mclk1", "mclk2";*/
gpio-controller;
#gpio-cells = <2>;
wlf,gpio-defaults = <
ARIZONA_GP_FN_TXLRCLK
ARIZONA_GP_DEFAULT
ARIZONA_GP_DEFAULT
ARIZONA_GP_DEFAULT
ARIZONA_GP_DEFAULT
>;
wlf,reset = <&gpio1 28 GPIO_ACTIVE_HIGH>; /* allow /RESET wm5102 by driver (via inverter)*/
wlf,ldoena = <&gpio1 29 GPIO_ACTIVE_HIGH>; /* allow LDOENA wm5102 by driver */
LDOVDD-supply = <&ldo18>; /* fixed 1V8 regulator */
AVDD-supply = <&ldo18>;
DBVDD1-supply = <&ldo18>;
DBVDD2-supply = <&ldo18>;
DBVDD3-supply = <&ldo18>;
CPVDD-supply = <&ldo18>;
/*DCVDD-supply = <&ldo18>; /* supplied by LDO1 */
MICVDD-supply = <&ldo50>;
SPKVDDL-supply = <&ldo50>; /* fixed VDD_5V from BBB */
SPKVDDR-supply = <&ldo50>;
#sound-dai-cells = <0>;
/* we haven't figured out how reference the internal LDO, pin is pulled up */
#if 0
ldo1: ldo1 {
wlf,ldoena = <&gpio1 29 GPIO_ACTIVE_HIGH>; /* allow LDOENA wm5102 by driver */
};
#endif
};
};
&mcasp0 {
pinctrl-names = "default";
pinctrl-0 = <&mcasp0_slave_pins_default>;
status = "okay";
op-mode = <0>; /* MCASP_IIS_MODE */
tdm-slots = <6>;
/* 4 serializers */
serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX - 0 2 0 0 */
2 0 0 0
>;
tx-num-evt = <32>;
rx-num-evt = <32>;
#sound-dai-cells = <0>;
};
&rtc {
system-power-controller;
};
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
