From: Paul Handrigan <Paul.Handrigan@xxxxxxxxxx>
Add device tree bindings file for the cs35l33 8V boosted
class D amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@xxxxxxxxxx>
---
.../devicetree/bindings/sound/cs35l33.txt | 73 ++++++++++++++++++++++
1 file changed, 73 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/cs35l33.txt
diff --git a/Documentation/devicetree/bindings/sound/cs35l33.txt b/Documentation/devicetree/bindings/sound/cs35l33.txt
new file mode 100644
index 0000000..273d73a
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs35l33.txt
@@ -0,0 +1,73 @@
+CS35L33 Speaker Amplifier
+
+Required properties:
+
+ - compatible : "cirrus,cs35l33"
+
+ - reg : the I2C address of the device for I2C
+
+ - VA-supply, VP-supply : power supplies for the device,
+ as covered in
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+ - reset-gpios : gpio used to reset the amplifier
+
+ - interrupt-parent : Specifies the phandle of the interrupt controller to
+ which the IRQs from CS35L33 are delivered to.
+ - interrupts : IRQ line info CS35L33.
+ (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+ for further information relating to interrupt properties)
+
+ - boost-ctl : Booster voltage use to supply the amp. If the value is
+ 0, then VBST = VP. If greater than 0, the boost voltage will be 3.3V with
+ a value of 1 and will increase at a step size of 0.1V until a maximum of
+ 8.0V.
+
+ - ramp-rate : On power up, it affects the time from when the power
+ up sequence begins to the time the audio reaches a full-scale output.
+ On power down, it affects the time from when the power-down sequence
+ begins to when the amplifier disables the PWM outputs. If this property
+ is not set then soft ramping will be disabled and ramp time would be
+ 20ms. If this property is set to 0,1,2,3 then ramp times would be 40ms,
+ 60ms,100ms,175ms respectively for 48KHz sample rate.
+
+ - boost-ipk : The maximum current allowed for the boost converter.
+ The range starts at 1.85A (0xF0) and goes to a maximum of 3.60A (0xE0)
+ with a step size of 0.015625A. The default is 2.50A (0x90).
+
+ - hg-algo : Parameters for internal Class H/G algorithm that
+ controls the amplifier supplies.
+
+Example:
+
+cs35l33: cs35l33@40 {
+ compatible = "cirrus,cs35l33";
+ reg = <0x40>;
+
+ VA-supply = <&ldo5_reg>;
+ VP-supply = <&ldo5_reg>;
+
+ interrupt-parent = <&gpio8>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&cs47l91 34 0>;
+
+ ramp-rate = <0x0>;
+ boost-ctl = <0x30>; /* VBST = 8.0V */
+ boost-ipk = <0xE0>; /* 3.60A */
+
+ hg-algo {
+ mem-depth = <0x3>;
+ release-rate = <0x3>;
+ hd-rm = <0xA>;
+ ldo-thld = <0x1>;
+ ldo-path-disable = <0x0>;
+ ldo-entry-delay=<0x4>;
+ vp-hg-auto;
+ vp-hg=<0xF>;
+ vp-hg-rate=<0x2>;
+ vp-hg-va=<0x0>;
+ };
+};
--
1.9.1
_______________________________________________
Alsa-devel mailing list
Alsa-devel@xxxxxxxxxxxxxxxx
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
