Re: [PATCH v5 3/3] riscv: dts: starfive: add the node and pins configuration for tdm

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2023/5/31 14:23, Hal Feng wrote:
> On Fri, 26 May 2023 22:54:02 +0800, Walker Chen wrote:
>> Add the tdm controller node and pins configuration of tdm for the
>> StarFive JH7110 SoC.
>> 
>> Signed-off-by: Walker Chen <walker.chen@xxxxxxxxxxxxxxxx>
>> ---
>>  .../jh7110-starfive-visionfive-2.dtsi         | 40 +++++++++++++++++++
>>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 21 ++++++++++
>>  2 files changed, 61 insertions(+)
>> 
>> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> index 1155b97b593d..19b5954ee72d 100644
>> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> @@ -214,6 +214,40 @@
>>  			slew-rate = <0>;
>>  		};
>>  	};
>> +
>> +	tdm0_pins: tdm0-pins {
>> +		tdm0-pins-tx {
> 
> Use consistent naming, so
> 
> 	tdm_pins: tdm-0 {
> 		tx-pins {
> 
>> +			pinmux = <GPIOMUX(44, GPOUT_SYS_TDM_TXD,
>> +					      GPOEN_ENABLE,
>> +					      GPI_NONE)>;
>> +			bias-pull-up;
>> +			drive-strength = <2>;
>> +			input-disable;
>> +			input-schmitt-disable;
>> +			slew-rate = <0>;
>> +		};
>> +
>> +		tdm0-pins-rx {
> 
> 		rx-pins {
> 
>> +			pinmux = <GPIOMUX(61, GPOUT_HIGH,
>> +					      GPOEN_DISABLE,
>> +					      GPI_SYS_TDM_RXD)>;
>> +			input-enable;
>> +		};
>> +
>> +		tdm0-pins-sync {
> 
> 		sync-pins {
> 
>> +			pinmux = <GPIOMUX(63, GPOUT_HIGH,
>> +					      GPOEN_DISABLE,
>> +					      GPI_SYS_TDM_SYNC)>;
>> +			input-enable;
>> +		};
>> +
>> +		tdm0-pins-pcmclk {
> 
> 		pcmclk-pins {
> 
>> +			pinmux = <GPIOMUX(38, GPOUT_HIGH,
>> +					      GPOEN_DISABLE,
>> +					      GPI_SYS_TDM_CLK)>;
>> +			input-enable;
>> +		};
>> +	};
>>  };
>>  
>>  &uart0 {
>> @@ -221,3 +255,9 @@
>>  	pinctrl-0 = <&uart0_pins>;
>>  	status = "okay";
>>  };
>> +
>> +&tdm {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&tdm0_pins>;
> 
> 	pinctrl-0 = <&tdm_pins>;
> 
> Best regards,
> Hal

OK, I'll update these node's name in the next submit.
Thanks.

Best regards,
Walker



[Index of Archives]     [ALSA User]     [Linux Audio Users]     [Pulse Audio]     [Kernel Archive]     [Asterisk PBX]     [Photo Sharing]     [Linux Sound]     [Video 4 Linux]     [Gimp]     [Yosemite News]

  Powered by Linux