On 09/17/2013 09:23 PM, Dave Anderson wrote:
----- Original Message -----
On 09/17/2013 03:33 PM, HATAYAMA Daisuke wrote:
(2013/09/17 16:12), Jingbai Ma wrote:
On 09/17/2013 02:55 PM, HATAYAMA Daisuke wrote:
int32_t, int64_t, uint64_t, etc ... are parts of C99 standard:
http://en.wikipedia.org/wiki/C_data_types
All there types have been supported by GCC, so them should work on all
the architectures.
Although change these persistent data structure will affect both
makedumpfile and crash utility, but we will benefit from the
consistent data structures independent from architectures. We can
analyze a dumpfile on a OS with different architecture than the
crashed OS.
I know stdint.h things and usefulness if we can use crash and makedumpfile
for a multiple architectures on single arch. In fact, crash already supports
cross platform build among some architectures thanks to Dave.
But only if the host and target architectures have the same endian-ness and
whose data type sizes match.
If we have a standard for the dump file format, we can handle all the
endian-ness issues.
I know it may affect the dumping speed on the platform that has to
convert the byte order. But at least we can specify the byte order for
dump file header. It won't cost too much.
The only problem that has ever been seen with the current header declarations
is if an x86 crash binary is built to support the 32-bit ARM architecture.
For x86, the 64-bit off_t variables can start on a 4-byte boundary, but on ARM,
they have to start on an 8-byte boundary. That being the case, the off_t
offset_vmcoreinfo is at offset 20 when built on an x86, and at offset 24
when built on ARM:
This could be addressed through compiler attributes:
off_t offset_vmcoreinfo __atttribute__ ((aligned(8));
offset_vmcoreinfo will be the same 8-byte boundary on x86 as same as ARM
struct kdump_sub_header {
unsigned long phys_base;
int dump_level; /* header_version 1 and later */
int split; /* header_version 2 and later */
unsigned long start_pfn; /* header_version 2 and later */
unsigned long end_pfn; /* header_version 2 and later */
off_t offset_vmcoreinfo; /* header_version 3 and later */
unsigned long size_vmcoreinfo; /* header_version 3 and later */
off_t offset_note; /* header_version 4 and later */
unsigned long size_note; /* header_version 4 and later */
off_t offset_eraseinfo; /* header_version 5 and later */
unsigned long size_eraseinfo; /* header_version 5 and later */
};
Do you like this change?
struct kdump_sub_header {
unsigned long phys_base;
int dump_level;
int split;
unsigned long start_pfn;
unsigned long end_pfn;
off_t offset_vmcoreinfo __atttribute__ ((aligned(8));
unsigned long size_vmcoreinfo;
off_t offset_note __atttribute__ ((aligned(8));
unsigned long size_note;
off_t offset_eraseinfo __atttribute__ ((aligned(8));
unsigned long size_eraseinfo;
};
Then you can get rid of the padded struct kdump_sub_header_ARM_target in
crash utility.
Or we can go further, redefine whole structure and set all fields with
specific bit width.
struct kdump_sub_header {
uint64_t phys_base;
int32_t dump_level;
int32_t split;
uint64_t start_pfn;
uint64_t end_pfn;
uint64_t offset_vmcoreinfo;
uint64_t size_vmcoreinfo;
uint64_t offset_note;
uint64_t size_note;
uint64_t offset_eraseinfo;
uint64_t size_eraseinfo;
};
I have checked the code of crash utility, it shouldn't affect too much,
only in diskdump.c and diskdump.h.
So for that anomoly, crash has to support a kdump_sub_header_ARM_target
structure that has a pad integer after the end_pfn variable.
My question came from the fact that it looks like you introduced a single
modified kdump_sub_header structure for all the architectures. They might
have different combination of length between int and long and maybe
also have other each architecture specific incompatibility. It wouldn't
work well.
But from your reply, I think you mean a fully new header for
kdump-compressed
format, right? If so, it must work well. But of course you need to modify
both of makedumpfile and crash utility to support it.
Yes, I would like to have a new header for kdump-compressed format. But
I'm not sure how much code will be affected in makedumpfile and crash utility.
I'm still under investigating, any ideas would be appreciated.
The challenging part will be the requirement to maintain backwards-compatibility,
at least in the crash utility. And backwards-compatibility would also be required
in makedumpfile, right? For example, if you want to re-filter an older compressed
kdump.
It's not a big deal, we can check the header_version to decide treat it
as traditional format or new format.
We can preserve the current structures as kdump_sub_header_v5 ,
kdump_sub_header_v5, etc... in both makedumpfile and crash utility.
But if -- as has been done so far -- an increment of the header_version in the
disk_dump_header to signal an additional field in the kdump_sub_header would be
trivial to implement.
Yes, this approach is more simpler, but the drawback is we have to add a
new 64bit max_mapnr_64 to disk_dump_header, then we will have two
max_mapnr* fields, not very nice. And when we add more platforms, we
still have to take care of the bit width and alignment.
Should we fix it in this version or just leave it as it used to be?
Dave
--
Thanks,
Jingbai Ma
--
Crash-utility mailing list
Crash-utility@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/crash-utility