Re: [PATCH v1 08/10] arm64: dts: qcom: qrb4210-rb2: enable wsa881x amplifier

[Krzysztof Kozlowski <krzk@xxxxxxxxxx>]

On Fri, Nov 01, 2024 at 05:31:52AM +0000, Alexey Klimov wrote:
> One WSA881X amplifier is connected on QRB4210 RB2 board
> hence only mono speaker is supported. This amplifier is set
> to work in analog mode only. Also add required powerdown
> pins/gpios.
> 
> Cc: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
> Signed-off-by: Alexey Klimov <alexey.klimov@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 45 ++++++++++++++++++++++++
>  1 file changed, 45 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
> index fc71f5930688..76b9ae1b0ebc 100644
> --- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
> +++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts
> @@ -63,6 +63,16 @@ hdmi_con: endpoint {
>  		};
>  	};
>  
> +	i2c0_gpio: i2c0 {

Is 0 name on the schematics or datasheet? If yes, then i2c-0. If not,
then i2c-1


> +		compatible = "i2c-gpio";
> +
> +		sda-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
> +		scl-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "disabled";
> +	};
> +
>  	i2c2_gpio: i2c {

i2c-(x+1)


>  		compatible = "i2c-gpio";
>  
> @@ -272,6 +282,25 @@ zap-shader {
>  	};
>  };
>  
> +&i2c0_gpio {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	wsa881x: codec@f {
> +		compatible = "qcom,qrb4210-wsa881x-i2c-codec";
> +		reg = <0x0f>;
> +		pinctrl-0 = <&wsa_en_active>;
> +		pinctrl-1 = <&wsa_en_sleep>;
> +		pinctrl-names = "default", "sleep";
> +		clocks = <&q6afecc LPASS_CLK_ID_MCLK_2 LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> +		clock-names = "wsa_mclk";
> +		powerdown-gpios = <&lpass_tlmm 16 GPIO_ACTIVE_LOW>;
> +		mclk-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_HIGH>;
> +		sound-name-prefix = "SpkrMono";
> +		#sound-dai-cells = <0>;
> +	};
> +};
> +
>  &i2c2_gpio {
>  	clock-frequency = <400000>;
>  	status = "okay";
> @@ -746,6 +775,22 @@ wcd_reset_n_sleep: wcd-reset-n-sleep-state {
>  		bias-disable;
>  		output-low;
>  	};
> +
> +	wsa_en_active: wsa-en-active-state {
> +		pins = "gpio106";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		bias-disable;
> +		output-high;
> +	};
> +
> +	wsa_en_sleep: wsa-en-sleep-state {
> +		pins = "gpio106";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +		input-enable;

Are you sure this passes dtbs_check? I think this was not allowed since
1.5 years.

Best regards,
Krzysztof