On 09/25/2016 02:27 PM, jd1008 wrote:
On 09/25/2016 02:17 PM, Lawrence E Graves wrote:
On 09/25/2016 01:54 PM, jd1008 wrote:
On 09/25/2016 01:41 PM, Lawrence E Graves wrote:
On 09/25/2016 01:38 PM, jd1008 wrote:
On 09/25/2016 01:14 PM, Lawrence E Graves wrote:
On 09/25/2016 01:01 PM, jd1008 wrote:
On 09/25/2016 12:50 PM, Lawrence E Graves wrote:
On 09/25/2016 12:45 PM, Ahmad Samir wrote:
On 25 September 2016 at 18:06, Lawrence E Graves
<lgraves95@xxxxxxxxx> wrote:
This the results of what you just told me. Hope it makes
sense to you.
[root@Jehovah ~]# /usr/bin/liveusb-creator
file:///usr/lib64/qt5/qml/QtQuick/Controls/ComboBox.qml:560:5:
QML Menu:
Binding loop detected for property "__selectedIndex"
QOpenGLShaderProgram: could not create shader program
QOpenGLShader: could not create shader
QOpenGLShader: could not create shader
shader compilation failed:
QOpenGLShaderProgram::uniformLocation( matrix ): shader
program is not
linked
QOpenGLShaderProgram::uniformLocation( opacity ): shader
program is not
linked
QOpenGLShaderProgram: could not create shader program
QOpenGLShader: could not create shader
QOpenGLShader: could not create shader
shader compilation failed:""
A shot in the dark, try running it as user, not root:
liveusb-creator_polkit
this should show a polkit dialogue where you have to type your
root
password to authenticate.
_______________________________________________
users mailing list -- users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to
users-leave@xxxxxxxxxxxxxxxxxxxxxxx
This is what happen when I did what you asked.
file:///usr/lib64/qt5/qml/QtQuick/Controls/ComboBox.qml:560:5:
QML Menu: Binding loop detected for property "__selectedIndex"
QOpenGLShaderProgram: could not create shader program
QOpenGLShader: could not create shader
QOpenGLShader: could not create shader
shader compilation failed:
...
When I run liveusb-creator as root:
# liveusb-creator
Qt: Session management error: None of the authentication
protocols specified are supported
/org/freedesktop/UDisks2/block_devices/sdb
and the GUI interface pops up
and it works.
_______________________________________________
users mailing list -- users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to users-leave@xxxxxxxxxxxxxxxxxxxxxxx
I get the same results. It doesn't make sense to me. I have never
had any trouble with it before.
I think the problem might be that liveusb-creator
is trying to communicate with /bin/dbus-daemon
and fails.
_______________________________________________
users mailing list -- users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to users-leave@xxxxxxxxxxxxxxxxxxxxxxx
Is there a way to fix that or will I have to wait until they fix it
with an update?
I should have also asked: are you at liberty to say in more detail
what you want to put on the USB?
For example, is it an iso file? a directory of software including
the boot sector, ...etc
_______________________________________________
users mailing list -- users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to users-leave@xxxxxxxxxxxxxxxxxxxxxxx
Yes, I was trying to load a usb drive with Fedora 25 Alpha to try it
out.
In that case, assuming your USB has enough room, all you need to do is
sudo dd if=<full-path-name-fedora25-iso> of=/dev/sd?? bs=16M
where /dev/sd?? is the pathname to the usb device.
Notice that '<' and '>' are not part of the iso file pathname.
If some time later you want to make use of the USB as an ordinary
disk (for read and write), all you need do is
sudo dd if=/dev/zero of=/dev/sd?? bs=16M
where /dev/sd?? is the pathname to the usb device.
Reason why you neeed to dd /dev/zero into the usb device
if you want to read/write it as a regular disk, is that after you
dd the iso image into it, fedora will only recognize it as a read only
optical device.
Good luck
_______________________________________________
users mailing list -- users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to users-leave@xxxxxxxxxxxxxxxxxxxxxxx
Unless I did something wrong, that didn't work either. This the results:
[root@Jehovah ~]# dd if=<full-path-name-fedora25-iso> of=/dev/sd?? bs=16M
-bash: full-path-name-fedora25-iso: No such file or directory
[root@Jehovah ~]# dd if= full-path-name-fedora25-iso of=/dev/sd?? bs=16M
dd: unrecognized operand ‘full-path-name-fedora25-iso’
Try 'dd --help' for more information.
[root@Jehovah ~]# dd if=<full-path-name-fedora25-iso>
of=/home/lawrence69/Downloads bs=16M
-bash: full-path-name-fedora25-iso: No such file or directory
[root@Jehovah ~]#
[root@Jehovah ~]# dd if=<full-path-name-fedora25-iso>
of=/home/lawrence69/Downloads bs=16M
-bash: full-path-name-fedora25-iso: No such file or directory
[root@Jehovah ~]# dd if= full-path-name-fedora25-iso
of=/home/lawrence69/Downloads bs=16M
dd: unrecognized operand ‘full-path-name-fedora25-iso’
Try 'dd --help' for more information.
[root@Jehovah ~]# dd if=/dev/zero of=/dev/sd?? bs=16M
dd: error writing '/dev/sd??': No space left on device
751+0 records in
750+0 records out
12598886400 bytes (13 GB, 12 GiB) copied, 3.37454 s, 3.7 GB/s
[
--
All things are workable but don't all things work.
Prov. 3:5 & 6
_______________________________________________
users mailing list -- users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to users-leave@xxxxxxxxxxxxxxxxxxxxxxx
