Hello,
After a fresh install of libvirt in a box with one physical interface
(eth0), I tried to set up a bridged network in br0:
[ifcfg-eth0:]
DEVICE=eth0
HWADDR=48:5b:39:ba:f9:2a
NM_CONTROLLED=no
BRIDGE="br0"
ONBOOT=yes
NETMASK=255.255.255.0
IPADDR=192.168.0.10
GATEWAY=192.168.0.2
DNS2=192.168.0.6
TYPE=Ethernet
BOOTPROTO=none
DNS1=192.168.0.5
IPV6INIT=no
USERCTL=no
[ifcfg-br0]
DEVICE=br0
TYPE=Bridge
BOOTPROT="dhcp"
ONBOOT=yes
DELAY=0
NM_CONTROLLED=no
BOOTPROTO=dhcp
IPV6INIT=no
USERCTL=no
After that I get this:
br0 Link encap:Ethernet HWaddr 48:5B:39:BA:F9:2A
inet addr:192.168.0.122 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::4a5b:39ff:feba:f92a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:398 errors:0 dropped:0 overruns:0 frame:0
TX packets:156 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:36074 (35.2 KiB) TX bytes:23902 (23.3 KiB)
eth0 Link encap:Ethernet HWaddr 48:5B:39:BA:F9:2A
inet6 addr: fe80::4a5b:39ff:feba:f92a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:417 errors:0 dropped:0 overruns:0 frame:0
TX packets:167 errors:0 dropped:0 overruns:0 carrier:2
collisions:0 txqueuelen:1000
RX bytes:43047 (42.0 KiB) TX bytes:24860 (24.2 KiB)
Interrupt:28
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
virbr0 Link encap:Ethernet HWaddr 8E:37:DB:3B:46:3F
inet addr:192.168.122.1 Bcast:192.168.122.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
And now I don't have an IP address in eth0, but I have one br0.
Is something wrong here? I see that eth0 have "Interrupt:28", what this
mean?
Thanks in advance.
Best regards,
Lázaro.
Este mensaje de correo electrónico ha sido procesado por el servidor de Frioclima
--
users mailing list
users@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe or change subscription options:
https://admin.fedoraproject.org/mailman/listinfo/users
Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
