------------------------------ Message: 14 Date: Sun, 07 May 2006 20:51:27 +0100 From: Andy Burns <fedora@xxxxxxxxxxxxxx> Subject: Re: PC Card To: For users of Fedora Core releases <fedora-list@xxxxxxxxxx> Message-ID: <445E4FBF.5040403@xxxxxxxxxxxxxx> Content-Type: text/plain; charset=ISO-8859-1; format=flowed Annette T Robart wrote: > 05:00.0 Ethernet controller: Abocom Systems Inc: Unknown device ab03 (rev > 11) Is this device (which seems to be detected as eth0) *another* ethernet device apart from your PC(MCIA) card? Any reason not to use it? ---------- I only have the "one" card. ------------------------------ Message: 15 Date: Sun, 07 May 2006 14:52:49 -0500 From: "Mikkel L. Ellertson" <mikkel@xxxxxxxxxxxxxxxx> Subject: Re: PC Card To: For users of Fedora Core releases <fedora-list@xxxxxxxxxx> Message-ID: <445E5011.7000604@xxxxxxxxxxxxxxxx> Content-Type: text/plain; charset=ISO-8859-1 Annette T Robart wrote: > ------------------------------ > > Message: 15 > Date: Sun, 07 May 2006 19:28:49 +0100 > From: Andy Burns <fedora@xxxxxxxxxxxxxx> > Subject: Re: PC Card > To: For users of Fedora Core releases <fedora-list@xxxxxxxxxx> > Message-ID: <445E3C61.2070902@xxxxxxxxxxxxxx> > Content-Type: text/plain; charset=ISO-8859-1; format=flowed > > Annette T Robart wrote: > >> I need help with finding, and installing drivers for my linksys >> etherfast PC card. > > Can you get start a terminal window and then include the output of the > following commands? > > su - > > lspci > > ifconfig -a > <------------------------[ SNIP ] -------------------------> > 05:00.0 Ethernet controller: Abocom Systems Inc: Unknown device ab03 (rev > 11) > ifconfig -a > eth0 Link encap:Ethernet HWaddr 00:E0:98:8E:C8:EA > BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:11 Base address:0x1000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:149 errors:0 dropped:0 overruns:0 frame:0 > TX packets:149 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:9879 (9.6 Kb) TX bytes:9879 (9.6 Kb) > > Thanks > > It looks like Linux has already installed the driver for you. All you need to do is configure the card. At least the device number matched the one for the Linksys card. It is listed as an Abocom System but it not unusual for the PCI ID to be from a different manufacturer. And ifconfig know you have an Ether net interface that is not up and/or not configured. Mikkel -- Do not meddle in the affairs of dragons, for thou art crunchy and taste good with Ketchup! ------------------------------ I went into network device control, (if that is where I need to go) and set it to active and dhcp, etc and activate device when computer starts. When I reboot computer I get a red failed and it shows "interface eth0 not found", And it is too fast to read but something about tulip does not seem to be present?? -- fedora-list mailing list fedora-list@xxxxxxxxxx To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
