Nevermind, fixed it with cursor entries below. Section "Device" Identifier "Card0" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "Radeon RV100 QY [Radeon 7000/VE]" Option "HWCursor" "off" Option "SWCursor" "on" -----Original Message----- From: Cicone, Anthony Sent: Wednesday, February 02, 2011 5:44 PM To: Cicone, Anthony; 'sparc@xxxxxxxxxxxxxxxxxxxxxxx' Subject: RE: boot hangs at Attached SCSI disk Hi List, I was abled to finally get FC-12 to install and boot on my Sunblade 2500 with XVR-100 by using the kernel-2.6.31.12-174.2.25.fc12.sparc64 version. I was able to configure Xorg, but now my cursor is a big square, with lines through it? Here is my xorg.conf: Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "catalogue:/etc/X11/fontpath.d" FontPath "built-ins" EndSection Section "Module" Load "radeon" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" Identifier "Card0" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "Radeon RV100 QY [Radeon 7000/VE]" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 16 EndSubSection EndSection Thanks again. -----Original Message----- From: Cicone, Anthony Sent: Tuesday, January 11, 2011 10:49 AM To: 'sparc@xxxxxxxxxxxxxxxxxxxxxxx' Subject: RE: boot hangs at Attached SCSI disk Thanks for your help, but I've gotten closer with the 2.6.32.19-163 kernel. It gets past the "Attached SCSI disk" but hangs here: scsi target0:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31) scsi target0:0:1: Ending Domain Validation sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:1:0: Attached scsi generic sg1 type 0 sd 0:0:0:0: [sda] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 0:0:1:0: [sdb] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 0:0:1:0: [sdb] Write Protect is off sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and F UA sdb: sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and F UA sdb3 sd 0:0:1:0: [sdb] Attached SCSI disk sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. dracut: Mounted root filesystem /dev/sda2 dracut: Loading SELinux policy dracut: + [ -x /sysroot/sbin/load_policy ] dracut: + chroot /sysroot /sbin/load_policy -i SELinux: Disabled at runtime. type=1404 audit(1294759926.279:2): selinux=0 auid=4294967295 ses=4294967295 dracut: /sbin/load_policy: Can't load policy: No such file or directory dracut: + ret=2 dracut: Switching root type=1305 audit(1294759927.929:5): auid=4294967295 ses=4294967295 op="remove rul e" key=(null) list=4 res=0 type=1305 audit(1294759927.929:6): audit_enabled=0 old=1 auid=4294967295 ses=429 4967295 res=1 -----Original Message----- From: sparc-bounces@xxxxxxxxxxxxxxxxxxxxxxx [mailto:sparc-bounces@xxxxxxxxxxxxxxxxxxxxxxx] On Behalf Of Rich Mahn Sent: Tuesday, January 11, 2011 9:14 AM To: sparc@xxxxxxxxxxxxxxxxxxxxxxx Subject: Re: boot hangs at Attached SCSI disk first i apologize for the non-threading of this post. since there are so few posts on this list it hopefully it won't be too much a problem. > Hello All, > > I was able succesfully install Fedora Sparc 9 on a Sunblade 2500 with > XVR-100 card, and everything worked great. I could never get FC-14 to > work, but I have recently been trying to insall FC-14 on the same > hardware again, and have not been successful. The installation works > fine, but when I boot, it always hangs at the "Attached SCSI disk"? > I'm able to then boot off the rescue CD, and mount everthing in the > chroot environment, and everything looks good? I had devil of a time getting anything working on a Bullfrog which had a XVR-100. It took me weeks to get a kernel that would work (boot to a prompt). According to not-so-clear notes I took at the time, some of the items that had a lot of effect (good or bad) were the I2C settings (had to be off), and SERIO_18042 (had to be off). I'm attaching my config file for the kernel. Don't know if this will help or not, but it's what I am now able to use for both the Bullfrogs and other sparcs as well. This is for 2.6.33, so I don't know how relevent it is to FC-14. I can provide the kernel for you as well, if that will help. T. Rowe Price (including T. Rowe Price Group, Inc. and its affiliates) and its associates do not provide legal or tax advice. Any tax-related discussion contained in this e-mail, including any attachments, is not intended or written to be used, and cannot be used, for the purpose of (i) avoiding any tax penalties or (ii) promoting, marketing, or recommending to any other party any transaction or matter addressed herein. Please consult your independent legal counsel and/or professional tax advisor regarding any legal or tax issues raised in this e-mail. The contents of this e-mail and any attachments are intended solely for the use of the named addressee(s) and may contain confidential and/or privileged information. Any unauthorized use, copying, disclosure, or distribution of the contents of this e-mail is strictly prohibited by the sender and may be unlawful. If you are not the intended recipient, please notify the sender immediately and delete this e-mail. _______________________________________________ sparc mailing list sparc@xxxxxxxxxxxxxxxxxxxxxxx https://admin.fedoraproject.org/mailman/listinfo/sparc